Recherche « zephyrproject zephyr »

zephyrproject zephyr

The Nuvoton NPCX eSPI driver parses Target-Attached-Flash (TAF) requests in espi_taf_parse() (drivers/espi/espi_npcx.c), taking the 12-bit length field directly out of the request header in the FLASHRXBUF FIFO. For write and RPMC OP1 requests it copied DIV_ROUND_UP(len, 4) words into struct espi_taf_pckt.src, a fixed 16-word (64-byte) member of a static structure, without ever comparing the length against that buffer or against the negotiated eSPI receive payload size (rx-plsize, 64 bytes on all in-tree NPCX/NPCK SoCs). Both the loop counter and the word count were uint8_t, so the copy ran up to 255 iterations. An eSPI controller that emits a flash request whose header claims a payload larger than the negotiated maximum therefore drives up to 239 32-bit stores past the end of the structure — roughly 956 bytes of out-of-bounds write into .bss — from the eSPI flash receive interrupt handler, while the source reads walk past the end of the 18-word FLASHRXBUF register array into neighbouring eSPI registers. The same unvalidated length was then passed on to flash_write() in espi_taf_npcx_flash_write() with the 64-byte src buffer as source, reading up to 4 KB of adjacent controller SRAM into SPI flash at a host-chosen address, where the host can read it back. A related fixed-size stack buffer in taf_npcx_completion_handler() was overflowed by four bytes on the maximum-size completion path on SoCs whose tx-plsize is 64. The defect is reachable only from the eSPI host side, and only by a request that violates the negotiated payload size, so it requires host firmware or bus-level control rather than ordinary host software; a compliant maximum-length write fits the buffer exactly and is handled correctly. Because TAF exists specifically so that the embedded controller arbitrates host access to shared flash (espi_taf_check_read_protect() / espi_taf_check_write_protect()), corrupting controller memory from a host-supplied field crosses the trust boundary the feature asserts; consequences range from controller crash or hang to corruption of driver state that gates the flash protection regions. The fix widens the counters, rejects any request whose word count exceeds both ARRAY_SIZE(FLASHRXBUF) - NPCX_ESPI_FLASH_HEADER_ADDRESS_LEN and NPCX_TAF_RX_PAYLOAD_WORDS (derived from the devicetree rx-plsize), marks such packets with a new invalid_flag so espi_taf_work() answers them with an unsuccessful completion instead of processing them, bounds the transmit payload against FLASHTXBUF, and adds a default case for unsupported cycle types. Only configurations with CONFIG_ESPI_TAF enabled on an NPCX/NPCK target are affected; no in-tree board enables it by default.

zephyrproject zephyr

The Infineon PSOC 6 BLESS HCI driver in drivers/bluetooth/hci/hci_infineon_psoc6_bless.c stored the outgoing HCI packet descriptor in a file-scope variable, static cy_stc_ble_hci_tx_packet_info_t hci_tx_pkt. psoc6_bless_send() cleared and populated that descriptor's packetType, dataLength and data fields before acquiring psoc6_bless_operation_sem, so the driver's serialising semaphore protected only the call into Cy_BLE_SoftHciSendAppPkt() and not the shared state that call reads. The Bluetooth host does not guarantee a single HCI sender. Most transmissions are funnelled through the cooperative TX-processor work queue, but bt_hci_cmd_send() deliberately bypasses bt_dev.cmd_tx_queue for BT_HCI_OP_HOST_NUM_COMPLETED_PACKETS and calls bt_send() directly from the caller's thread; that caller is bt_hci_host_num_completed_packets(), the acl_in_pool destroy callback, which runs on whichever thread drops the last reference to a received ACL buffer. CONFIG_BT_HCI_ACL_FLOW_CONTROL defaults to y on this driver's boards, and an application that returns -EINPROGRESS from its L2CAP recv callback and later calls bt_l2cap_chan_recv_complete() performs that unref from its own preemptible thread. A remote peer that generates Bluetooth traffic concurrently with the device's own transmissions raises the collision rate. When two senders interleave, the semaphore holder can hand the controller a descriptor whose dataLength comes from one net_buf and whose data pointer comes from another — or one whose buffer has already been returned to its pool. The controller then copies and transmits up to a full HCI/ACL payload starting at a shorter or recycled buffer, disclosing adjacent RAM contents to the connected peer; other interleavings duplicate one HCI packet and silently drop another, disrupting the link. The driver only reads through the shared descriptor, so no memory corruption or write primitive results, and the disclosed bytes are not attacker-chosen. The fix makes the descriptor a local variable in psoc6_bless_send(), removing the shared state; Cy_BLE_SoftHciSendAppPkt() copies the packet before returning, so it need not outlive the call.

zephyrproject zephyr

The Broadcom AFBR-S50 time-of-flight sensor driver double-completes an RTIO submission when sensor data evaluation fails. In data_ready_work_handler() (drivers/sensor/broadcom/afbr_s50/afbr_s50.c), a non-STATUS_OK return from Argus_EvaluateData() calls handle_error_on_result(), which finalises the request with rtio_iodev_sqe_err(), but execution then fell through to the tail of the function and finalised the very same struct rtio_iodev_sqe a second time with rtio_iodev_sqe_ok(). Unlike the other error branches in the same function, this one did not return. Both completion helpers reach rtio_executor_done() in subsys/rtio/rtio_executor.c, which returns the submission to the pool via rtio_sqe_pool_free() and, for streaming (multishot) submissions, also releases the RX buffer with rtio_release_buffer(). The second completion therefore reads a freed rtio_iodev_sqe, pushes the same mpsc node onto the submission queue while it is already on the pool free list — splicing the two lists together — and re-submits the freed request so the next measurement is written through an already-released buffer. For one-shot submissions it emits a spurious success completion carrying stale userdata and frees the same pool entry twice. The failure branch is driven by sensor conditions rather than by host software. The vendor API documents statuses such as ERROR_ARGUS_BIAS_VOLTAGE_REINIT and ERROR_ARGUS_LASER_MONITOR_INACTIVE as transient results of harsh ambient light, so a party in front of the optical sensor can provoke the invalid-data condition without any physical contact with the board or any software access; SPI transfer errors reach the same branch. In releases before the payload.Status check was dropped, ordinary sharp distance transitions in the sensor's field of view were sufficient. Impact is corruption of the RTIO submission pool and mempool bookkeeping: aliased submissions, writes through released buffers, and duplicate completions delivered to the application. The attacker does not control the corrupted content, so the practical consequence is memory corruption and loss of availability on devices that instantiate brcm,afbr-s50, rather than directed code execution. Only builds that enable this driver are affected.

zephyrproject zephyr

The device multiplexer pseudo-driver in drivers/misc/devmux/devmux.c exposes two system calls, devmux_select_get() and devmux_select_set(). When CONFIG_USERSPACE is enabled, their user-mode verifiers z_vrfy_devmux_select_get() and z_vrfy_devmux_select_set() forwarded directly to the kernel implementations without performing any kernel-object validation — no k_object_access_check() and no driver object check. Compounding this, DEVICE_DT_INST_DEFINE() registered devmux instances with a NULL driver API pointer, which causes scripts/build/gen_kobject_list.py to skip them entirely, so a devmux device had no struct k_object and no permission on it could be granted or withheld in the first place. Any thread running in user mode can reach the defect: device pointers such as DEVICE_DT_GET(DT_NODELABEL(devmux0)) are compile-time constants available to application code, and the syscall accepted them from a thread that had never been granted access to the device. The kernel implementations do validate the pointer against the static devmux instance table and bounds-check the selection index, so this is not a memory-safety issue; the failure is purely one of authorization. Exposure requires CONFIG_USERSPACE=y together with the experimental CONFIG_DEVMUX=y (which depends on CONFIG_DEVICE_MUTABLE) and a zephyr,devmux devicetree node. An unprivileged user-mode thread can read and change which downstream device a multiplexer forwards to, bypassing the userspace object-permission model. Because a devmux forwards the data, configuration and API of the selected device — its documented use being zephyr,console and zephyr,shell-uart switching — an attacker can suppress console, log and shell output, redirect that output to a downstream device it is able to observe, or flip the selection underneath another thread that is legitimately using the multiplexer. The impact is bounded to the devicetree-fixed set of downstream devices; no out-of-bounds access or arbitrary pointer dereference is reachable. The fix declares __subsystem struct devmux_driver_api and attaches a DEVICE_API(devmux, devmux_api) instance to each devmux device so that it becomes a tracked K_OBJ_DRIVER_DEVMUX kernel object, and adds K_OOPS(devmux_inst_get(dev) == SIZE_MAX) plus K_OOPS(k_object_access_check(dev) != 0) to both verifiers.

zephyrproject zephyr

The Bluetooth Classic Hands-Free Profile HF role in subsys/bluetooth/host/classic/hfp_hf.c does not release the AT command buffers that are still queued on hf->tx_pending when the RFCOMM DLC goes down. hfp_hf_disconnected() only cancelled the work items and cleared hf->acl, and no other code path ever dequeues those buffers, so each one is permanently lost from the fixed hf_pool (CONFIG_BT_MAX_CONN + 1 buffers, i.e. two in the default configuration). The same function also left BT_HFP_HF_FLAG_CONNECTED set, and hfp_hf_create() wiped the object with memset() as soon as hf->acl was NULL, without checking whether hf->work, hf->slc_work or hf->deferred_work was still pending or running. The remote Audio Gateway peer controls the trigger end to end and needs no application involvement: an unsolicited +BCS: 1 response makes bcs_handle() call bt_hfp_hf_select_codec() and queue an AT+BCS buffer, which cannot be transmitted while BT_HFP_HF_FLAG_RX_ONGOING is set, and an immediately following RFCOMM DISC strands that buffer. Repeating the connect / +BCS / disconnect cycle a couple of times empties hf_pool for good. With the pool exhausted, HFP command sending fails permanently, and because hfp_hf_send_cmd() allocates with K_FOREVER (bt_rfcomm_create_pdu() → bt_conn_create_pdu()) from the Bluetooth RX context — where that timeout is not downgraded to K_NO_WAIT — one further +BCS from the peer parks the Bluetooth RX thread inside net_buf_alloc() with no possible waker, halting all HCI event processing until the device is rebooted. Separately, reusing the HF slot while a work handler was still queued or running allowed memset() to wipe live k_work items out from under the system workqueue, corrupting shared kernel workqueue state. Exploitation requires an established HFP session (for SSP devices L2CAP enforces authentication before the RFCOMM channel is reachable) and a build with CONFIG_BT_HFP_HF enabled.

zephyrproject zephyr

The user-mode syscall verifier z_vrfy_rtio_cqe_get_mempool_buffer() in subsys/rtio/rtio_syscalls.c validated its two output parameters, buff and buff_len, with K_SYSCALL_MEMORY_READ() rather than K_SYSCALL_MEMORY_WRITE(). Both are pure out-parameters: z_impl_rtio_cqe_get_mempool_buffer() stores the mempool buffer address and its length through them. The distinction is enforced by every architecture validator — arch_buffer_validate() on RISC-V PMP explicitly accepts the global __rom_region/__rodata_region for reads only, and the ARM MPU validators accept P_RO_U_RO and P_RW_U_RO regions for reads only — so a read-validated pointer is not necessarily writable by the calling thread. An unprivileged user-mode thread that has been granted access to an RTIO context (rtio_access_grant()) can invoke the rtio_cqe_get_mempool_buffer() syscall with buff/buff_len pointing at memory it may read but not write, and with a completion-queue entry whose flags field it fully controls (only RTIO_CQE_FLAG_MEMPOOL_BUFFER in flags[7:0] is required; flags[19:8] and flags[31:20] supply the block index and count). The kernel then performs a pointer-sized and a 4-byte store through those addresses while running in supervisor mode. Reaching the store requires CONFIG_USERSPACE together with CONFIG_RTIO_SYS_MEM_BLOCKS, the configuration behind RTIO_DEFINE_WITH_MEMPOOL; without the latter the implementation returns -ENOTSUP and writes nothing. Two outcomes follow. If the target lies in a memory-domain partition declared K_MEM_PARTITION_P_RW_U_RO (privileged read-write, user read-only), the kernel-mode store succeeds and deposits partly attacker-chosen values into memory the memory domain had marked read-only for that thread, bypassing the partition's write protection. If the target lies in globally readable but unwritable memory such as .text/.rodata in flash, the store faults in kernel mode; the fault is delivered to z_fatal_error() and the default k_sys_fatal_error_handler() halts or reboots the device, giving an unprivileged thread a reliable full denial of service. The read-permission check does bound the damage: the address must still be readable by the calling thread, so kernel-private memory cannot be targeted and no confidential data is disclosed. The fix replaces both checks with K_SYSCALL_MEMORY_WRITE(), so a thread lacking write permission is terminated by K_OOPS before the implementation runs; the cqe argument correctly remains read-validated.

zephyrproject zephyr

The UpdateHub firmware-over-the-air client parses the CoAP probe response with Zephyr's JSON library in z_impl_updatehub_probe() (subsys/mgmt/updatehub/updatehub.c). The decoder treats every descriptor field as optional — json_obj_parse() returns a bitmask of the fields it actually decoded and never fails on a missing one — so a response that omits the "sha256sum" string leaves the corresponding const char * in the zero-initialised struct resp_probe_any_boards / struct resp_probe_some_boards at NULL. Both metadata branches then computed sha256size = strlen(...objects.sha256sum) + 1 before any validation, dereferencing that NULL pointer; the SHA256_HEX_DIGEST_SIZE test that follows operates on a value the bad read has already produced and cannot prevent it. The metadata is supplied entirely by the network peer: probe_cb() accepts the datagram, runs coap_packet_parse() and copies the payload with no token matching and no cryptographic check. With CONFIG_UPDATEHUB_DTLS unset — the default — start_coap_client() uses plain CoAP over UDP on port 5683 with no peer authentication and resolves the server via unauthenticated DNS, so an on-path attacker, a DNS spoofer, or an off-path attacker who wins the race with a forged source address can deliver the malformed metadata. A probe response as simple as "objects":[[{}],[{}]] suffices, and no user interaction is required because updatehub_autohandler() polls on CONFIG_UPDATEHUB_POLL_INTERVAL. When CONFIG_UPDATEHUB_DTLS=y the trigger narrows to a malicious or compromised update server. The primitive is a read at address zero, not a write, so the impact is availability only. On targets where the low address range is unmapped or protected — MMU-based architectures, builds with CONFIG_NULL_POINTER_EXCEPTION_DETECTION_DWT/_MPU/_PMP, TrustZone non-secure images, and SoCs such as nRF54L whose 0x0–0x400 window is unmapped — the load faults and Zephyr's default fatal handler halts the system, giving a remotely re-triggerable denial of service on every poll. On classic Cortex-M targets where the vector table is readable at address zero the walk usually terminates immediately and the request is rejected by the length check, so the outcome is configuration- and SoC-dependent. There is no memory write, and the copied bytes are only compared against the locally computed image hash, so there is no information-disclosure channel. The fix adds an explicit sha256sum == NULL test that returns UPDATEHUB_METADATA_ERROR ahead of the strlen() in both metadata branches. Debug builds (CONFIG_UPDATEHUB_LOG_LEVEL=4) still format the same pointers with %s in a LOG_DBG() loop that runs before the new checks, so that variant remains in debug configurations only.

zephyrproject zephyr

The Link Layer Control Procedure (LLCP) implementation of the Zephyr software Bluetooth LE Controller retains the receive node that carried an accepted LL_PHY_UPDATE_IND so that it can later be reused for the host notification when the update instant is reached (llcp_rx_node_retain() in subsys/bluetooth/controller/ll_sw/ull_llcp.c, and the node is deliberately not recycled while marked NODE_RX_TYPE_RETAIN). The invalid-PDU arms of llcp_lp_pu_rx() and llcp_rp_pu_rx() in subsys/bluetooth/controller/ll_sw/ull_llcp_phy.c completed the procedure via llcp_lr_complete() / llcp_rr_complete() without first releasing that retained node, so the procedure context — the only remaining reference to the node — was freed while the node was still held out of the receive pool. A peer device on an established LE connection can drive this deterministically and without pairing or encryption. Against a peripheral it sends LL_PHY_REQ, receives LL_PHY_RSP, sends a valid LL_PHY_UPDATE_IND with an instant a few connection events in the future (so the node becomes retained), and then, before the instant is reached, sends any other LL Control PDU such as LL_LENGTH_REQ; ull_cp_rx() routes it to the active remote PHY Update procedure, which takes the invalid-PDU path. The mirror case applies to a locally initiated PHY Update followed by an LL_REJECT_IND. In the default configuration (CONFIG_BT_ASSERT and CONFIG_BT_CTLR_ASSERT_DEBUG both default y) the violated invariant in llcp_lr_check_done() / llcp_rr_check_done() triggers a controller assertion, ending in k_oops() (or k_panic()) — a single crafted PDU sequence from radio range faults the device. With those assertions compiled out, each attempt silently leaks one receive PDU node and its memq link; because the controller receive pool is small (PDU_RX_CNT, driven by CONFIG_BT_CTLR_RX_BUFFERS, which defaults to 1) and each attempt costs the attacker only a reconnect, a few repetitions exhaust the pool and leave Bluetooth inoperable until reboot. On releases v3.4.0 through v3.7.x the assertion is never reached, whatever the configuration, so every attempt leaks silently. The impact is limited to availability: the orphaned node leaves no dangling pointer that is later dereferenced and is never delivered to the host, so there is no memory corruption or information disclosure. The same pull request applies the identical release to the Connection Update and CIS-create procedures, whose invalid-PDU arms had the same omission.

zephyrproject zephyr

The Bluetooth Link Layer control procedure code in subsys/bluetooth/controller/ll_sw/ull_llcp_conn_upd.c retains the received RX node while a Connection Update / Connection Parameter procedure waits for its instant, so the node can later carry the host notification (llcp_rx_node_retain(), which marks it NODE_RX_TYPE_RETAIN and thereby suppresses the normal recycling in ull.c). The default: arm of llcp_rp_cu_rx() and llcp_lp_cu_rx() — the "invalid PDU, terminate the connection" path — completed the procedure without releasing that retained node. llcp_rr_check_done() then dequeued and freed the procedure context with ctx->node_ref.rx still pointing at the retained node, dropping the last reference to it. A peer device in radio range can reach this without pairing, bonding, or encryption. Against a peripheral, the peer sends a well-formed LL_CONNECTION_UPDATE_IND with an instant a few connection events in the future (the node is retained and the procedure enters RP_CU_STATE_WAIT_INSTANT), then, before the instant is reached, sends any other LL Control PDU such as LL_LENGTH_REQ. ull_cp_rx() routes that PDU into the active remote Connection Update procedure, which takes the invalid-PDU path. The central role is reachable symmetrically after accepting an LL_CONNECTION_PARAM_REQ, and the local-procedure variant is reachable with LL_REJECT_IND. With CONFIG_BT_CTLR_ASSERT_DEBUG enabled (its default), the resulting state violates the invariant asserted in llcp_rr_check_done(), so the two-PDU sequence produces an immediate fatal error in the controller. With those asserts disabled, each occurrence permanently loses one node from the controller's small fixed RX pool (sized from CONFIG_BT_CTLR_RX_BUFFERS, which defaults to 1); repeating the sequence across reconnections exhausts the pool, after which the link-layer receive path operates on a NULL node. The impact is an unauthenticated, remotely triggerable denial of service persisting until reboot; there is no memory-disclosure or memory-corruption consequence, since the leaked node simply becomes unreachable.

zephyrproject zephyr

The Bluetooth Link Layer Control Procedure (LLCP) implementation for Connected Isochronous Stream (CIS) creation retains an RX node (ctx->node_ref.rx, marked NODE_RX_TYPE_RETAIN) so it can later be reused as the host notification — on the peripheral while awaiting the Host's reply to an LL_CIS_REQ, and on the central for the whole duration of a locally initiated CIS Create. In subsys/bluetooth/controller/ll_sw/ull_llcp_cc.c, the "invalid PDU received" paths of llcp_rp_cc_rx() and llcp_lp_cc_rx() terminated the connection and completed the procedure without releasing that retained node, breaking the invariant checked in llcp_lr_check_done() and llcp_rr_check_done() and orphaning the node's memory. A peer device within radio range can reach this with a single extra LL Control PDU on an unauthenticated, unencrypted ACL link. Against a peripheral, the attacker sends a valid LL_CIS_REQ and then, before the Host replies, any unrelated LL Control PDU (for example LL_VERSION_IND), which ull_cp_rx() routes into the active remote procedure. Against a central performing a CIS Create, a malicious peripheral answers with LL_UNKNOWN_RSP for CIS_REQ, which is dispatched into the active local procedure. No pairing, encryption or user interaction is required; the code is compiled in when CONFIG_BT_CTLR_PERIPHERAL_ISO or CONFIG_BT_CTLR_CENTRAL_ISO is enabled. In default builds (CONFIG_BT_CTLR_ASSERT_DEBUG is default y) the retained-node assertion fires immediately, producing a controller fatal error and, typically, a system reset from one injected PDU. With the development assertions disabled, each attempt permanently loses one node from the controller's small LL notification pool (LL_PDU_RX_CNT, 2 * CONFIG_BT_CTLR_LLCP_CONN) together with its memq_link_t; repeating the connect-attack-reconnect cycle exhausts the pool, after which notification allocation always fails, RX flow control stalls, and the non-disableable LL_ASSERT_ERR() in llcp_lp_cc_flush() faults. The impact is limited to availability — the leaked node is orphaned, never reused or double-freed — and recovery requires a reboot.

zephyrproject zephyr

i2s_esp32_trigger_check() in drivers/i2s/i2s_esp32.c validates the requested direction only for I2S_DIR_BOTH. The I2S_DIR_RX and I2S_DIR_TX branches read dev_cfg->rx.data->configured / dev_cfg->tx.data->configured without first checking the stream pointers. The device instantiation macro I2S_ESP32_STREAM_INIT() sets both .conf and .data to NULL for a direction the devicetree does not describe, so on an instance that wires only one direction — the normal shape for audio output or a worldsemi,ws2812-i2s LED strip — the other direction dereferences a NULL pointer instead of returning an error. i2s_trigger() is a Zephyr syscall, and z_vrfy_i2s_trigger() in drivers/i2s/i2s_handlers.c validates only the device object and the presence of the trigger API pointer; the dir argument is passed to the driver unvalidated. On a build with CONFIG_USERSPACE enabled, a user-mode thread that has been granted the I2S device can issue a single i2s_trigger() call naming the unwired direction and cause a load from address 0 in kernel mode. Among the Espressif parts that carry this driver, userspace is available in-tree only on RISC-V SoCs with CONFIG_RISCV_PMP, and v4.4.0 is the first release where that is buildable: the ESP32-C6 HPCORE selects RISCV_PMP when it is not built for MCUboot. ESP32-C5 in v4.4.x carries the same PMP-region and userspace linker support but does not select RISCV_PMP by default. Espressif Xtensa targets do not support Zephyr userspace, and in a non-userspace build the bad direction can only come from in-kernel application code. The impact is limited to availability: the access is a read at offset 0 of the missing stream structure, so there is no attacker-controlled offset, no write primitive and no information disclosure. With the default fatal-error handler the resulting exception halts the system, giving an unprivileged user-mode thread a system-wide denial of service. The fix adds the same pointer check the I2S_DIR_BOTH branch already performed and returns -ENOSYS for a direction the instance does not implement; the driver's other entry points (i2s_esp32_config_check(), i2s_esp32_config_get(), i2s_esp32_read(), i2s_esp32_write()) already guarded the pointers, and a static audit found no equivalent unguarded path. The driver defect is older than the affected range. The unguarded dereference is present from v4.2.0 (reached through i2s_esp32_trigger_stream(), whose if (stream) guard tests the address of a struct member and is never false) and takes its present i2s_esp32_trigger_check() form in v4.3.0. No in-tree Espressif configuration before v4.4.0 can run a user-mode thread, so in v4.2.x and v4.3.x the direction argument can only come from trusted kernel code. Those releases carry the bug but are not listed as affected; the fix has also been merged to v4.3-branch as hardening.

zephyrproject zephyr

The RFC 6528 initial-sequence-number implementation in subsys/net/ip/tcp.c derived every TCP ISN from SHA-256(unique_key || four-tuple) plus a uptime-derived offset, where unique_key is a 128-bit secret filled once by sys_csrand_get(). The return value of that call was discarded and the once guard was latched to true even when the call failed. Because sys_csrand_get() leaves the destination buffer untouched on failure (it deliberately propagates the entropy-driver error rather than filling the buffer), a single failed call left unique_key as its all-zero BSS content for the remainder of the boot, with no retry, no log message and no fallback. A failure of the cryptographic random source is required to reach the weak state — for example -ENODEV/-EIO from the entropy driver in subsys/random/random_entropy_device.c (the in-tree comment notes that the hardware RNG "might still be gathering entropy during early boot situations"), or psa_generate_random() failing in subsys/random/random_psa.c when PSA crypto is not initialised or is backed by a Bluetooth-HCI entropy device that is not yet up. The first TCP connection is what triggers key generation, so a remote peer that reaches a listening port immediately after boot, or that can provoke a reboot, has indirect influence over whether generation coincides with that window. tcp_init_isn() is called for every passive open in tcp_conn_new() and every active open in net_tcp_connect(), so the poisoned key governs all TCP connections for that boot. With an all-zero key the ISN becomes a public function of the connection four-tuple plus a device-wide time offset. An off-path attacker can compute the hash term offline for any four-tuple and recover the shared time offset from a single observed ISN, after which the ISN the device will pick for other four-tuples is predictable. That defeats exactly the protection RFC 6528 provides: blind TCP connection spoofing against peers that trust the source address, and blind data injection into or reset of connections whose four-tuple can be guessed. Devices whose entropy source never errors were never in the weak state. The fix moves key generation into a single guarded helper that latches only on success, logs the error otherwise, and makes tcp_init_isn() fall back to sys_rand32_get() — the behaviour already used when CONFIG_NET_TCP_ISN_RFC6528 is disabled — instead of hashing with a known-constant key.

zephyrproject zephyr

The Goodix GT9xx input driver in drivers/input/input_gt911.c reads the touch point count from the controller's status register and masks it with GT911_TOUCH_POINTS_MSK (0x0F), yielding a value of 0..15. In gt911_process() that value is used directly as the loop bound for filling point_reg[], a stack array sized to CONFIG_INPUT_GT911_MAX_TOUCH_POINTS, whose Kconfig range is 1..5 with a default of 1. No other check constrains the count; the driver relied only on a comment asserting that the controller had been programmed at init to report no more points than configured. Each loop iteration issues an I2C read of eight bytes straight into point_reg[i], so a controller that reports more points than the array holds causes up to 112 bytes of peer-supplied data to be written past the end of the array, over the stack frame of gt911_process() in the system workqueue thread. Two further loops then read out of bounds from the same array. Triggering it requires control of, or the ability to substitute, the I2C touch controller — plausible on the many supported boards where the GT9xx panel is a pluggable display module or shield rather than an on-PCB part; a spoofed device need only answer the init probes with a supported product ID and a checksum-valid config blob. The same overflow can also occur non-adversarially, with a GT9271-class panel that ignores the driver's touch-count programming and reports up to ten points, or with bus corruption of the single status byte. The impact is an out-of-bounds stack write with fully attacker-chosen content executing at kernel privilege, i.e. potential control-flow hijack on the host MCU, in addition to out-of-bounds reads and crashes. The attack vector is physical/local hardware access only; there is no network, USB, or syscall path to the defect. The fix clamps the reported count with min() against CONFIG_INPUT_GT911_MAX_TOUCH_POINTS before any array indexing.

zephyrproject zephyr

The ITE IT8xxx2 SHI host-command backend (subsys/mgmt/ec_host_cmd/backends/ec_host_cmd_backend_shi_ite.c) copied the 8-byte host-command request header from the SPI Rx FIFO directly into the shared receive buffer data->in_msg and only afterwards checked the protocol version and the derived packet length. The interrupt handler also accepted a chip-select assertion and an Rx-valid-length (RVLI) interrupt in any driver state other than SHI_STATE_DISABLED, so a new header could be parsed while the host-command thread was still processing the previous request out of the very same buffer. The host processor is the SPI controller and drives both chip select and the clock. After sending a well-formed request it can immediately de-assert chip select — which returns the driver to the ready state and re-enables the FIFO — and start a second transaction carrying a header with data_len = 0xFFFF. Those eight bytes are written into in_msg before the oversized length is rejected, so they land in a buffer whose contents verify_rx() in subsys/mgmt/ec_host_cmd/ec_host_cmd_handler.c has already validated. If this lands in the window before the host-command thread executes args.input_buf_size = rx_header->data_len, the framework hands the registered command handler a 65535-byte input length over a 256-byte buffer. The result is an out-of-bounds read of up to roughly 64 KiB beyond the request buffer: command handlers that copy or echo input_buf_size bytes disclose adjacent embedded-controller memory back to the host or overflow the response buffer, and a read past the end of SRAM faults the controller. The same race also allows cmd_id and cmd_ver to be swapped after checksum verification and after handler lookup. Exploitation requires the ability to drive the inter-processor SHI bus (a compromised host OS or physical access to the SPI lines) and winning a timing race, which the SPI controller can retry indefinitely. The fix parses the header into a local struct ec_host_cmd_request_header and copies it into in_msg only after the length has been bounded by sizeof(data->in_msg), and ignores chip-select and RVLI interrupts outside SHI_STATE_READY_TO_RECV/SHI_STATE_RECEIVING. A residual, bounded race remains: an end-of-transaction interrupt still resets the state to ready while the host-command thread owns the buffer, so a valid second request can still overwrite the in-flight request's contents, unlike the NPCX backend which parks in SHI_STATE_CNL_RESP_NOT_RDY while the buffer is in use.