Recherche « Gnu sed »

Kusalkasilva Learning-Management-System

A vulnerability was determined in Kusalkasilva Learning-Management-System up to ffeb873f8803f1e9664384ff75000c7da45466d2. The impacted element is an unknown function of the file student_signup.php of the component Student Registration Endpoint. This manipulation causes sql injection. The attack may be initiated remotely. The exploit has been publicly disclosed and may be utilized. This product uses a rolling release model to deliver continuous updates. As a result, specific version information for affected or updated releases is not available. The project was informed of the problem early through an issue report but has not responded yet.

Linux

In the Linux kernel, the following vulnerability has been resolved: mips: select CONFIG_WEAK_REORDERING_BEYOND_LLSC from CONFIG_EYEQ On I6500 CPU cores, lld and scd give no ordering guarantees (same as all other instructions). To respect the assumption that arch_cmpxchg() is fully ordered, we must inject sync instructions above and below our lld/scd loops using the already in place WEAK_REORDERING_BEYOND_LLSC infrastructure. Otherwise, bad things can happen: [ 34.054496] CPU 3 Unable to handle kernel paging request at virtual address 0000000000000000, epc == a80000080838e01c, ra == a80000080838dfc4 [ 34.054559] Oops[#1]: [ 34.069561] CPU: 3 UID: 0 PID: 170 Comm: pipe_race Not tainted 7.2.0-rc6-01553-gb73c35220968-dirty #103 VOLUNTARY [ 34.079932] Hardware name: Mobile EyeQ5 MP5 Evaluation board [ 34.085592] $ 0 : 0000000000000000 0000000000000001 0000000000000000 0000000000000000 [ 34.093616] $ 4 : a800000808ee2618 000000000b7a879d 0000000000001000 0000000000000000 [ 34.101638] $ 8 : 0000000000e3f2c9 0000000000000000 a800000808a2a9f8 0000000000000000 [ 34.109660] $12 : a8000008139ffcd8 ffffffff84080018 a80000080837fae0 7878787878787878 [ 34.117682] $16 : a800000807e82940 0000000000001000 0000000000000000 0000000000000000 [ 34.125704] $20 : a800000802920e00 a8000008139ffdf8 a800000802649400 0000000000e3f2c9 [ 34.133726] $24 : 0000000000000006 00000001200406e0 [ 34.141783] $28 : a8000008139fc000 a8000008139ffd10 0000000000e3f2c8 a80000080838dfc4 [ 34.149837] epc : a80000080838e01c anon_pipe_read+0xd4/0x428 [ 34.155697] ra : a80000080838dfc4 anon_pipe_read+0x7c/0x428 [ 34.161549] Status: 140000e3 KX SX UX KERNEL EXL IE [ 34.166551] Cause : 40800408 (ExcCode 02) [ 34.170574] BadVA : 0000000000000000 [ 34.174161] PrId : 0001b028 (MIPS I6500) [ 34.178183] Process pipe_race (pid: 170, threadinfo=000000005ca35720, task=00000000e1013890, tls=000000014ebbb780) [ 34.188568] Stack : a800000802649400 0000000000000000 0000000000000000 a8000008139ffdd0 [ 34.196623] 0000000000000fba a800000808ee0000 0000000000000001 a8000008130c3e80 [ 34.204676] a8000008080d1280 a8000008139ffd58 a8000008139ffd58 1dbd2b22ea1dd500 [ 34.212729] a800000802649400 a800000808ee0000 ffffffffffffffea 0000000000000001 [ 34.220783] 0000000000001000 0000000000000000 00000001200ae518 ffffffffffffffff [ 34.228836] 000000fffbe0e530 a80000080837edf4 000000fffbe0e530 0000000000000000 [ 34.236890] 0000000000000000 0000000000000000 000000014ebb55a0 0000000000001000 [ 34.244943] 0000000000000001 a800000802649400 0000000000000000 0000000000000000 [ 34.252996] 0000000000000000 0000400400000000 0000000000000000 1dbd2b22ea1dd500 [ 34.261049] 00000000140000e3 a800000802649400 a800000802649400 a800000808ee0000 [ 34.269103] ... [ 34.271568] Call Trace: [ 34.274026] [<a80000080838e01c>] anon_pipe_read+0xd4/0x428 [ 34.279533] [<a80000080837edf4>] vfs_read+0x25c/0x318 [ 34.284607] [<a80000080837faac>] ksys_read+0x104/0x138 [ 34.289763] [<a80000080802b9cc>] syscall_common+0x44/0x68 [ 34.295187] [ 34.296689] Code: f84000cf 02209825 de020010 <dc420000> d8400004 02002825 0040f809 02802025 f84000c3 [ 34.306504] [ 34.308099] ---[ end trace 0000000000000000 ]--- My initial reproducer was the xdp-tools test suite. A standalone reproducer would be an lld/scd loop that, when the read is reordered by the CPU, triggers a fault. We can achieve this from userspace by stressing an anonymous pipe, which uses a mutex. Program used: // SPDX-License-Identifier: GPL-2.0 // pipe_race.c - reproducer for MIPS LL/SC reordering vs fs/pipe.c // // Two userspace processes on an anonymous pipe: // parent = writer: tight write() loop // child = reader: tight read() loop #define _GNU_SOURCE #include <assert.h> #include <errno.h> #include <sched.h> #include <signal.h> #include <stdio.h> #include <stdlib.h> #include <string.h> #include <sys/types.h> #include ---truncated---

girishsaraf Online-Appointment-Booking-System

A security flaw has been discovered in girishsaraf Online-Appointment-Booking-System up to f427b4757128ca253d33d0cc4e87bbb9c999a4d5. Impacted is an unknown function of the file signup.php of the component Registration Handler. The manipulation of the argument fname results in sql injection. The attack can be executed remotely. The exploit has been released to the public and may be used for attacks. This product implements a rolling release for ongoing delivery, which means version information for affected or updated releases is unavailable. The project was informed of the problem early through an issue report but has not responded yet.

kishor-23 food-waste-management-system

A flaw has been found in kishor-23 food-waste-management-system 411989e3ecb82895e53dca7865f72145f03d7d93/b3a70b2c492dc9904de5be1ad9389bd79b87f82c. The impacted element is an unknown function of the file delivery/deliverysignup.php of the component Registration Page. This manipulation of the argument username/email/location causes sql injection. The attack can be initiated remotely. The exploit has been published and may be used. Continious delivery with rolling releases is used by this product. Therefore, no version details of affected nor updated releases are available. The project was informed of the problem early through an issue report but has not responded yet.

kishor-23 food-waste-management-system

A vulnerability was detected in kishor-23 food-waste-management-system 411989e3ecb82895e53dca7865f72145f03d7d93/b3a70b2c492dc9904de5be1ad9389bd79b87f82c. The affected element is an unknown function of the file admin/signup.php of the component Admin Registration. The manipulation of the argument email/username/location results in sql injection. It is possible to launch the attack remotely. The exploit is now public and may be used. This product takes the approach of rolling releases to provide continious delivery. Therefore, version details for affected and updated releases are not available. The project was informed of the problem early through an issue report but has not responded yet.

kishor-23 food-waste-management-system

A weakness has been identified in kishor-23 food-waste-management-system 411989e3ecb82895e53dca7865f72145f03d7d93/b3a70b2c492dc9904de5be1ad9389bd79b87f82c. This issue affects some unknown processing of the file signup.php of the component User Registration Endpoint. Executing a manipulation of the argument email/name/gender can lead to sql injection. The attack may be performed from remote. The exploit has been made available to the public and could be used for attacks. This product utilizes a rolling release system for continuous delivery, and as such, version information for affected or updated releases is not disclosed. The project was informed of the problem early through an issue report but has not responded yet.

kishor-23 food-waste-management-system

A weakness has been identified in kishor-23 food-waste-management-system 411989e3ecb82895e53dca7865f72145f03d7d93/b3a70b2c492dc9904de5be1ad9389bd79b87f82c. Affected is an unknown function of the file admin/signup.php of the component Admin Signup. This manipulation of the argument sign causes missing authentication. The attack can be initiated remotely. The exploit has been made available to the public and could be used for attacks. Continious delivery with rolling releases is used by this product. Therefore, no version details of affected nor updated releases are available. The project was informed of the problem early through an issue report but has not responded yet.

clavaque s2Member – Excellent for All Kinds of Memberships, Content Restriction Paywalls & Member Access Subscriptions

The s2Member – Excellent for All Kinds of Memberships, Content Restriction Paywalls & Member Access Subscriptions plugin for WordPress is vulnerable to Remote Code Execution in all versions up to, and including, 260814 via the 'first_name' parameter parameter. This is due to insufficient sanitization of the first_name parameter via esc_refs(), which strips only regex backreferences and not PHP tags, before substitution into the eval'd Signup Tracking Codes template, combined with disclosure of the site-global proxy verification key that allows PayPal postback verification to be bypassed. This makes it possible for unauthenticated attackers to execute code on the server. Successful exploitation requires that the site administrator has configured a Signup Tracking Codes template containing the %%first_name%% placeholder (a documented, GUI-supported feature) and that the attacker has obtained the site-global proxy verification key, which is exposed in plaintext in the JSON response of any PayPal Checkout AJAX request on the target site.

appwrite

Appwrite before 2.0.0 contains an argument injection vulnerability that allows authenticated users with functions.write or sites.write permissions to execute arbitrary commands by injecting TAB characters into the providerRootDirectory parameter used to construct GNU tar commands. The application uses escapeshellcmd instead of escapeshellarg and fails to quote the parameter, allowing TAB characters to survive sanitization and be interpreted as argument separators, enabling injection of arbitrary GNU tar arguments such as --checkpoint-action=exec to achieve remote code execution as the builds worker process user.

SourceCodester College Notes Gallery Management System

A security vulnerability has been detected in SourceCodester College Notes Gallery Management System 1.0. This impacts an unknown function of the file signup.php of the component Registration Flow. Such manipulation of the argument role leads to improper privilege management. The attack can be launched remotely. The exploit has been disclosed publicly and may be used.

GNU libextractor

GNU libextractor before 1.15 contains a stack-based buffer overflow vulnerability in the process_star_office function that sizes a variable-length stack array from attacker-controlled OLE2 stream data. Attackers can craft malicious StarOffice documents that allocate up to 4 MB on the stack, causing stack overflow and crashing any application extracting metadata from the document.

QWED-AI qwed-verification

QWED is open-source AI verification infrastructure for deterministic verification of LLM outputs, tool calls, code, schemas, and agent state before production execution. Prior to 5.1.2, the qwed package passes caller-controlled math expressions directly to SymPy parse_expr() without restricted global_dict and local_dict namespaces, allowing Python eval() to resolve builtins and execute arbitrary Python code in the API server process. In src/qwed_new/api/main.py, POST /verify/math is protected by get_current_tenant but accepts any valid tenant API key, reads the expression field, applies only a cosmetic re.sub(r'(\d)(()', r'\1*\2', expression) normalization, and passes the result to parse_expr(). In src/qwed_new/core/batch.py, POST /verify/batch sends math items through batch_service.create_job(), stores item.query verbatim, and _verify_item() passes VerificationType.MATH input to parse_expr() without sanitization. The default-enabled POST /auth/signup endpoint allows anyone to create a standard tenant account, POST /auth/api-keys issues an x-api-key, and either vulnerable path can then be used to read or write files, modify data, execute operating system commands, terminate the service, and compromise other tenants in a shared deployment. This issue is fixed in version 5.1.2.

Canonical accountsservice

The Ubuntu-specific language helper scripts (save-to-pam-env, update-langlist) shipped with accountsservice before 23.13.9-8ubuntu7 treat the user-controlled LANGUAGE entry in ~/.pam_environment as trusted input. The value is interpolated unescaped into a GNU sed replacement expression, allowing an attacker to inject a sed 'e' flag and arbitrary shell commands that execute with the privileges of the AccountsService helper process (real UID 0) via the SetLanguage D-Bus method.

Termix-SSH Termix

Termix is a web-based server management platform with SSH terminal, tunneling, and file editing capabilities. Prior to 2.3.2, the archive creation endpoint in src/backend/ssh/file-manager.ts passes selected file basenames to tar without an end-of-options marker and without making the operands unambiguously relative. A user with access to an SSH file-manager session can select basenames beginning with GNU tar options such as --checkpoint=1 and --checkpoint-action=exec, causing tar, tar.gz, tar.bz2, or tar.xz creation to interpret those names as options. The resulting checkpoint action executes commands on the managed SSH host with the privileges of the connected SSH account, allowing file disclosure, modification, and service disruption. This issue is fixed in version 2.3.2.

SourceCodester Photo Share Website

A vulnerability was found in SourceCodester Photo Share Website 1.0. This affects an unknown function of the file /social/ajax.php?action=signup. Performing a manipulation of the argument email results in sql injection. Remote exploitation of the attack is possible. The exploit has been made public and could be used.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem

In the Linux kernel, the following vulnerability has been resolved: posix-cpu-timers: Prevent UAF caused by non-leader exec() race Wongi and Jungwoo decoded and reported a non-leader exec() related race which can result in an UAF: sys_timer_delete() exec() posix_cpu_timer_del() // Observes old leader p = pid_task(pid, pid_type); de_thread() switch_leader(); release_task(old_leader) __exit_signal(old_leader) sighand = lock(old_leader, sighand); posix_cpu_timers*_exit(); sighand = lock_task_sighand(p) unhash_task(old_leader); sh = lock(p, sighand) old_leader->sighand = NULL; unlock(sighand); (p->sighand == NULL) unlock(sh) return NULL; // Returns without action if(!sighand) return 0; free_posix_timer(); This is "harmless" unless the deleted timer was armed and enqueued in p->signal because on exec() a TGID targeted timer is inherited. As sys_timer_delete() freed the underlying posix timer object run_posix_cpu_timers() or any timerqueue related add/delete operations on other timers will access the freed object's timerqueue node, which results in an UAF. There is a similar problem vs. posix_cpu_timer_set(). For regular posix timers it just transiently returns -ESRCH to user space, but for the use case in do_cpu_nanosleep() it's the same UAF just that the k_itimer is allocated on the stack. Also posix_cpu_timer_rearm() fails to rearm the timer, which means it stops to expire. While debating solutions Frederic pointed out another problem: posix_cpu_timer_del(tmr) __exit_signal(p) posix_cpu_timers*_exit(p); unhash_task(p); p->sighand = NULL; sh = lock_task_sighand(p) sighand = p->sighand; if (!sighand) return NULL; lock(sighand); if (!sh) WARN_ON_ONCE(timer_queued(tmr)); On weakly ordered architectures it is not guaranteed that posix_cpu_timer_del() will observe the stores in posix_cpu_timers*_exit() when p->sighand is observed as NULL, which means the WARN() can be a false positive. Solve these issues by: 1) Changing the store in __exit_signal() to smp_store_release(). 2) Adding a smp_acquire__after_ctrl_dep() into the !sighand path of lock_task_sighand(). 3) Creating a helper function for looking up the task and locking sighand which does not return when sighand == NULL. Instead it retries the task lookup and only if that fails it gives up. 4) Using that helper in the three affected functions. #1/#2 ensures that the reader side which observes sighand == NULL also observes all preceeding stores, i.e. the stores in posix_cpu_timers*_exit() and the ones in unhash_task(). #3 ensures that the above described non-leader exec() situation is handled gracefully. When the task lookup returns the old leader, but sighand == NULL then it retries. In the non-leader exec() case the subsequent task lookup will observe the new leader due to #1/#2. In normal exit() scenarios the subsequent lookup fails. When the task lookup fails, the function also checks whether the timer is still enqueued and issues a warning if that's the case. Unfortunately there is nothing which can be done about it, but as the task is already not longer visible the timer should not be accessed anymore. This check also requires memory ordering, which is not provided when the first lookup fails. To achieve that the check is preceeded by a smp_rmb() which pairs with the smp_wmb() in write_seqlock() in __exit_signal(). That ensures that the stores in posix_cpu_timers*_exit() are visible. The history of the non-leader exec() issue goes back to the early days of posix CPU timers, which stored a pointer to the group leader task in the timer. That obviously fails when a non-leader exec() switches the leader. commit e0a70217107e ("posix-cpu-timers: workaround to suppress the problems with mt exec") added a temporary workaround for that in 2010 which surv ---truncated---

GNU Bison

GNU Bison allows for an execution of an arbitrary program during HTML report generation due to improper handling of grammar-defined configuration variables. A grammar file can override the executable used for the XML‑to‑HTML transformation step via %define tool.xsltproc, which is accepted without restriction and passed directly to execvp(). When running bison --html on a attacker-provided grammar, this behavior allows execution of an arbitrary program with the privileges of the Bison process. Maintainers of this project were notified about this vulnerability, and fixed the issue in commit 3169c1e7a2c6acc4c59dfcf8b089896d6881925b. However, they did not provide vulnerable version range. Version 3.8.2 was tested and confirmed as vulnerable, other versions were not tested but might also be vulnerable.

Red Hat Enterprise Linux 10 · Red Hat Enterprise Linux 6 · Red Hat Enterprise Linux 7 · Red Hat Enterprise Linux 8

An out-of-bounds write vulnerability was found in the BFD library's DLX ELF backend (bfd/elf32-dlx.c) in GNU binutils. The dlx_rtype_to_howto() function maps ELF relocation types to internal howto structures but fails to perform adequate bounds checking on attacker-controlled relocation type values (via ELF32_R_TYPE(r_info)) before indexing into the dlx_elf_howto_table[] array. The DLX relocation type number space is non-contiguous (basic types 0-6, extended types at 0x10000+), but the default case in the switch statement allows arbitrary index values to reach the array access. A specially crafted ELF/DLX object file can trigger this out-of-bounds write when processed by any BFD-consuming tool (objdump, readelf, strip, ld, nm, objcopy). The vulnerability has been demonstrated to achieve arbitrary code execution via a File Stream Oriented Programming (FSOP) attack against glibc FILE structures (stderr), redirecting control flow to system(). Attack scenarios include CI/CD pipelines performing automated binary analysis, developer workstations running objdump/readelf on untrusted binaries, automated security scanning or malware analysis tools invoking binutils, and package build systems processing third-party code. Note: This vulnerability is only exploitable when binutils is built with the DLX backend enabled (typically via --enable-targets=all).

PHPOffice PhpSpreadsheet

PhpSpreadsheet is a pure PHP library for reading and writing spreadsheet files. In versions 4.0.0 through 5.8.0, 3.3.0 through 3.10.6, 2.2.0 through 2.4.6, 2.0.0 through 2.1.17, and all releases up to and including 1.30.5, the Gnumeric reader reads attacker-supplied .gnumeric files into memory and, when the file starts with gzip magic bytes, calls gzdecode() on the full compressed contents without enforcing a decompressed-size limit. A very small compressed .gnumeric file can expand to data larger than the PHP memory limit and crash the process during Gnumeric::canRead() before the file is rejected or fully parsed. This is reachable through normal file-type detection and Gnumeric loading paths, so applications that accept attacker-controlled spreadsheet uploads can suffer denial of service. This issue has been fixed in versions 5.8.1, 3.10.7, 2.4.7, 2.1.18 and 1.30.6.

ninenines cowlib

Allocation of resources without limits vulnerability in ninenines cowlib allows an unauthenticated remote HTTP/2 or HTTP/3 peer to exhaust memory on the vulnerable server (or client) and cause a denial of service. The HPACK and QPACK prefixed-integer decoder cow_hpack_common:dec_big_int/3 in src/cow_hpack_common.hrl (invoked from cow_hpack:decode/2 in src/cow_hpack.erl and from cow_qpack:decode_field_section/3 in src/cow_qpack.erl) reads continuation octets until it sees one whose high bit is clear, evaluating Int + (Value bsl M) at each step with the shift M growing by seven per octet. No limit is enforced on the number of continuation octets, on the resulting bit width, or on the value; the decoder consumes whatever encoded length the peer supplies. Because Erlang integers are immutable, each intermediate Value bsl M and each accumulator update allocates a fresh bignum whose digit width grows linearly with the number of octets processed so far. Summed across the whole decode, the transient bignum digit materialization is on the order of the square of the encoded length. A single maximal HPACK indexed representation carried inside one HTTP/2 HEADERS plus one CONTINUATION frame at Cowboy's default max_frame_size_received can force hundreds of megabytes of transient allocation and garbage-collection churn before the resulting header-table index is rejected as invalid. Repeated or concurrent connections multiply the pressure and can drive the Erlang VM to memory exhaustion. Cowlib is the HTTP parser used by Cowboy, RabbitMQ's management plugin, and other Erlang and Elixir HTTP/2 and HTTP/3 servers and clients, so any exposed endpoint that accepts HPACK or QPACK from an untrusted peer is reachable. This issue affects cowlib: from 2.0.0 before 2.19.0.

gpsd

gpsd through release-3.27.5, fixed at commit 4c06658, contains a code injection vulnerability in the gpsprof utility that allows an attacker who controls GPS input data to execute arbitrary OS commands by injecting malicious content into the SKY.satellites[].used field, which is inserted unsanitized into a gnuplot heredoc data block. Attackers can supply a used value containing the string EOD to terminate the heredoc early and append gnuplot system() calls, achieving OS command execution as the user running gpsprof when the generated plot script is processed by gnuplot in polar mode.

surrealdb · Surrealdb surrealdb

SurrealDB before 1.5.5 (and 2.0.0-beta before 2.0.0-beta.3) accepts an arbitrary object in the signin and signup operations of the RPC API without recursively validating it for non-computed values. When a record access method defines a SIGNIN or SIGNUP query and the RPC API is exposed to untrusted users, an unauthenticated attacker can encode a binary object containing a subquery using the bincode serialization format and supply it in place of credentials. The subquery is then executed within the database owner's SIGNIN/SIGNUP query under a system user session with the editor role, allowing the attacker to select, create, update, and delete non-IAM resources (though not view the query results directly, and not affect IAM resources, which require the owner role).

filebrowser

File Browser is a file managing interface for uploading, deleting, previewing, renaming, and editing files within a specified directory. Prior to 2.63.17, File Browser builds new user scopes from usernames passed through cleanUsername() when Signup=true and CreateUserDir=true, but the many-to-one normalization can collapse usernames such as team/one, team one, and team-one to the same home directory without checking whether the resulting scope is already taken, allowing a second registrant to gain full read and write access to another user's files. This issue is fixed in version 2.63.17.

GNU gawk · Fossies gawk

Buffer overflow vulnerability has been found in "extension/readdir.c" program file of gawk (ftype() routine). This issue could be used to crash the program and potentially to achieve code execution, although the latter has not been confirmed to be feasible. It affects gawk in versions 5.4.0 and below.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel · Siemens simatic s7-1500 tm mfp firmware

In the Linux kernel, the following vulnerability has been resolved: ipv6: account for fraggap on the paged allocation path In __ip6_append_data(), when the paged-allocation branch is taken (MSG_MORE / NETIF_F_SG / large fraglen), alloclen and pagedlen are computed as alloclen = fragheaderlen + transhdrlen; pagedlen = datalen - transhdrlen; datalen already includes fraggap (datalen = length + fraggap). When fraggap is non-zero, this is not the first skb and transhdrlen is zero. The fraggap bytes carried over from the previous skb are copied just past the fragment headers in the new skb's linear area. The linear area is therefore undersized by fraggap bytes while pagedlen is overstated by the same amount, and the copy writes past skb->end into the trailing skb_shared_info. An unprivileged user can trigger this via a UDPv6 socket using MSG_MORE together with MSG_SPLICE_PAGES. The bad accounting was introduced by commit 773ba4fe9104 ("ipv6: avoid partial copy for zc"). Before commit ce650a166335 ("udp6: Fix __ip6_append_data()'s handling of MSG_SPLICE_PAGES"), the negative copy value caused -EINVAL to be returned. That later commit allowed MSG_SPLICE_PAGES to proceed in this case, making the corruption triggerable. The non-paged branch sets alloclen to fraglen, which already accounts for fraggap because datalen does. Bring the paged branch in line by adding fraggap to alloclen and subtracting it from pagedlen. After this adjustment, copy no longer collapses to -fraggap on the paged path, so remove the stale comment describing that old arithmetic. Since a negative copy is no longer expected for a valid MSG_SPLICE_PAGES case, remove the MSG_SPLICE_PAGES exception from the negative copy check.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: use chan timer to close channels in cleanup_listen() l2cap_chan_close() removes the channel from conn->chan_l, which must be done under conn->lock. cleanup_listen() runs under the parent sk_lock, so acquiring conn->lock would invert the established conn->lock -> chan->lock -> sk_lock order. Instead of calling l2cap_chan_close() directly, schedule l2cap_chan_timeout with delay 0 to close the channel asynchronously. The timeout handler already acquires conn->lock and chan->lock in the correct order. The timer is only armed when chan->conn is still set: if it is already NULL, l2cap_conn_del() has already processed this channel (l2cap_chan_del + l2cap_sock_teardown_cb + l2cap_sock_close_cb), so there is nothing left to do. If l2cap_conn_del() races in after the timer is armed, __clear_chan_timer() inside l2cap_chan_del() cancels it; if the timer has already fired, the handler returns harmlessly because chan->conn was cleared.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gem: Fix phys BO pread/pwrite with offset sg_page() returns struct page pointer not (void *) so the scaling of pread/pwrite is wrong for phys BO and wrong parts of BO would be accessed if non-zero offset is used. Last impacted platform with overlay or cursor planes using phys mapping was Gen3/945G/Lakeport. (cherry picked from commit 3e49a2f85070b2fb672c1e0fdba281a4ea3aebe6)

GNU gzip

GNU gzip contains a global buffer overflow vulnerability in the LZH decompression logic caused by improper reuse of shared global state between different decompression formats within a single execution. GNU gzip maintains a global array that is shared across the LZ77, LZW, and LZH decompression routines and is not reinitialized between files processed in the same invocation. By decompressing a specially crafted LZW file followed by a specially crafted LZH file in a single gzip -d command, an attacker can poison the shared global state and subsequently trigger an out‑of‑bounds read in the LZH decoder. The LZH decompression logic follows stale values left in the shared array, causing reads past the end of the allocated global buffer. This issue has been fixed in commits 63dbf6b3b9e6e781df1a6a64e609b10e23969681 and e7378c2d421be6a286922374425680bbe9ad8b7d.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem

In the Linux kernel, the following vulnerability has been resolved: ipv6: mcast: Fix use-after-free when processing MLD queries When processing an MLD query, a pointer to the multicast group address is retrieved when initially parsing the packet. This pointer is later dereferenced without being reloaded despite the fact that the skb header might have been reallocated following the pskb_may_pull() calls, leading to a use-after-free [1]. Fix by copying the multicast group address when the packet is initially parsed. [1] BUG: KASAN: slab-use-after-free in __mld_query_work (net/ipv6/mcast.c:1512) Read of size 8 at addr ffff8881154b8e90 by task kworker/4:1/118 Workqueue: mld mld_query_work Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:94 lib/dump_stack.c:120) print_address_description.constprop.0 (mm/kasan/report.c:378) print_report (mm/kasan/report.c:482) kasan_report (mm/kasan/report.c:595) __mld_query_work (net/ipv6/mcast.c:1512) mld_query_work (net/ipv6/mcast.c:1563) process_one_work (kernel/workqueue.c:3314) worker_thread (kernel/workqueue.c:3397 kernel/workqueue.c:3478) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) </TASK> [...] Freed by task 118: kasan_save_stack (mm/kasan/common.c:57) kasan_save_track (mm/kasan/common.c:78) kasan_save_free_info (mm/kasan/generic.c:584) __kasan_slab_free (mm/kasan/common.c:253 mm/kasan/common.c:285) kfree (./include/linux/kasan.h:235 mm/slub.c:2689 mm/slub.c:6251 mm/slub.c:6566) pskb_expand_head (net/core/skbuff.c:2335) __pskb_pull_tail (net/core/skbuff.c:2878 (discriminator 4)) __mld_query_work (net/ipv6/mcast.c:1495 (discriminator 1)) mld_query_work (net/ipv6/mcast.c:1563) process_one_work (kernel/workqueue.c:3314) worker_thread (kernel/workqueue.c:3397 kernel/workqueue.c:3478) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245)

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: net/sched: act_api: use RCU with deferred freeing for action lifecycle When NEWTFILTER and DELFILTER are run concurrently it is possible to create a race with an associated action. Let's illustrate with CPU0 running NEWTFILTER and CPU1 running DELFILTER: 0: mutex_lock() <-- holds the idr lock 0: rcu_read_lock() 0: p = idr_find(idr, index) <-- action p is valid (RCU protects IDR) 0: mutex_unlock() <-- releases the idr lock 1: refcount_dec_and_mutex_lock() <-- refcnt 1->0, mutex held 1: idr_remove(idr, index) <-- Action removed from IDR 1: mutex_unlock() <-- mutex released allowing us to delete the action 1: tcf_action_cleanup(p); kfree(p) <-- Kfrees p immediately, no deferral 0: refcount_inc_not_zero(&p->tcfa_refcnt) <-- ouch, UAF p points to freed memory This patch fixes the race condition between NEWTFILTER and DELFILTER by adding struct rcu_head to tc_action used in the deferral and introducing a call_rcu() in the delete path to defer the final kfree(). Note: this is a revert of commit d7fb60b9cafb ("net_sched: get rid of tcfa_rcu") but also modernization/simplification to directly use kfree_rcu(). Let's illustrate the new restored code path: 0: rcu_read_lock() 1: refcount_dec_and_mutex_lock() <-- refcnt 1->0, mutex held 1: idr_remove(idr, index) 1: mutex_unlock() 1: call_rcu(&p->tcfa_rcu, tcf_action_rcu_free) <-- defer kfree after grace period 0: p = idr_find(idr, index) 0: refcount_inc_not_zero(&p->tcfa_refcnt) <-- fails, refcnt already 0 1: rcu_read_unlock() <-- release so freeing can run after grace period After CPU1 calls idr_remove(), the object is no longer reachable through the IDR. CPU0's subsequent idr_find() will return NULL, and even if it still held a stale pointer, the immediate kfree() is now deferred until after the RCU grace period, so no UAF can occur.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem

In the Linux kernel, the following vulnerability has been resolved: xfrm: policy: fix use-after-free on inexact bin in xfrm_policy_bysel_ctx() Fix the race by pruning the bin while still holding xfrm_policy_lock, before dropping it. Use __xfrm_policy_inexact_prune_bin() directly since the lock is already held. The wrapper xfrm_policy_inexact_prune_bin() becomes unused and is removed. Race: CPU0 (XFRM_MSG_DELPOLICY) CPU1 (XFRM_MSG_NEWSPDINFO) ========================== ========================== xfrm_policy_bysel_ctx(): spin_lock_bh(xfrm_policy_lock) bin = xfrm_policy_inexact_lookup() __xfrm_policy_unlink(pol) spin_unlock_bh(xfrm_policy_lock) xfrm_policy_kill(ret) // wide window, lock not held xfrm_hash_rebuild(): spin_lock_bh(xfrm_policy_lock) __xfrm_policy_inexact_flush(): kfree_rcu(bin) // bin freed spin_unlock_bh(xfrm_policy_lock) xfrm_policy_inexact_prune_bin(bin) // UAF: bin is freed

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ALSA: timer: Fix UAF at snd_timer_user_params() At releasing a timer object, e.g. when a userspace timer (CONFIG_SND_UTIMER) gets closed and snd_timer_free() is called, it tries to detach the timer instances and release the resources. However, it's still possible that other in-flight tasks are holding the timer instance where the to-be-deleted timer object is associated, and this may lead to racy accesses. Fortunately, most of ioctls dealing with the timer instance list already have the protection with register_mutex, and this also avoids such races. But, SNDRV_TIMER_IOCTL_PARAMS isn't protected, hence the concurrent ioctl may lead to use-after-free. This patch just adds the guard with register_mutex to protect snd_timer_user_params() for covering the code path as a quick workaround. It's no hot-path but rather a rarely issued ioctl, so the performance penalty doesn't matter.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: udp: clear skb->dev before running a sockmap verdict On the UDP receive path skb->dev is repurposed as dev_scratch (the truesize/state cache set by udp_set_dev_scratch()), through the union { struct net_device *dev; unsigned long dev_scratch; } in sk_buff. When a UDP socket is in a sockmap, sk_data_ready is sk_psock_verdict_data_ready(), which calls udp_read_skb() -> recv_actor() (sk_psock_verdict_recv) to run the attached SK_SKB verdict program in softirq. If that program calls a socket-lookup helper (bpf_sk_lookup_tcp/udp, bpf_skc_lookup_tcp), bpf_skc_lookup() does: if (skb->dev) caller_net = dev_net(skb->dev); skb->dev still holds the dev_scratch value (a non-NULL integer), so dev_net() dereferences it as a struct net_device * and the kernel takes a general protection fault on a non-canonical address in softirq: Oops: general protection fault, probably for non-canonical address 0x1010000800004a0 CPU: 1 UID: 0 PID: 1406 Comm: syz.2.19 Not tainted 7.1.0-rc6 #1 PREEMPT(full) RIP: 0010:bpf_skc_lookup net/core/filter.c:7033 [inline] RIP: 0010:bpf_sk_lookup+0x45/0x160 net/core/filter.c:7047 Call Trace: <IRQ> bpf_prog_4675cb904b7071f8+0x12e/0x14e bpf_prog_run_pin_on_cpu+0xc6/0x1f0 sk_psock_verdict_recv+0x1ba/0x350 udp_read_skb+0x31a/0x370 sk_psock_verdict_data_ready+0x2e3/0x600 __udp_enqueue_schedule_skb+0x4c8/0x650 udpv6_queue_rcv_one_skb+0x3ec/0x740 udp6_unicast_rcv_skb+0x11d/0x140 ip6_protocol_deliver_rcu+0x61e/0x950 ip6_input_finish+0xa9/0x150 NF_HOOK+0x286/0x2f0 ip6_input+0x117/0x220 NF_HOOK+0x286/0x2f0 __netif_receive_skb+0x85/0x200 process_backlog+0x374/0x9a0 __napi_poll+0x4f/0x1c0 net_rx_action+0x3b0/0x770 handle_softirqs+0x15a/0x460 do_softirq+0x57/0x80 </IRQ> The rmem charge that dev_scratch accounted for is released by skb_recv_udp() on dequeue, just above, so the scratch is dead by the time recv_actor() runs. Clear skb->dev so bpf_skc_lookup() falls back to sock_net(skb->sk), which skb_set_owner_sk_safe() set just above.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Validate XDomain request packet size before type cast tb_xdp_handle_request() casts the received packet buffer to protocol-specific structs without verifying that the allocation is large enough for the target type. A peer can send a minimal XDomain packet that passes the generic header length check but is shorter than the struct accessed after the cast, causing out-of- bounds reads from the kmemdup allocation. Plumb the packet length through xdomain_request_work and validate it against the expected struct size before each cast.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Clamp VBIOS HDMI retimer register count to array size [Why & How] The VBIOS integrated info tables (v1_11 and v2_1) contain HdmiRegNum and Hdmi6GRegNum fields that are used as loop bounds when copying retimer I2C register settings into fixed-size arrays (dp*_ext_hdmi_reg_settings[9] and dp*_ext_hdmi_6g_reg_settings[3]). These u8 fields are not validated before use, so a malformed VBIOS can specify values up to 255, causing an out-of-bounds heap write during driver probe. Clamp each register count to the destination array size using min_t() before the copy loops, in both get_integrated_info_v11() and get_integrated_info_v2_1(). (cherry picked from commit 5a7f0ef90195940c54b0f5bb85b87da55f038c69)

Rapid7 InsightConnect Sed Plugin · Gnu sed

OS Command Injection vulnerability in Rapid7 InsightConnect Sed Plugin on Linux allows authenticated attackers to execute arbitrary OS commands via the expression parameter due to insufficient input validation.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem

In the Linux kernel, the following vulnerability has been resolved: fs/fcntl: fix SOFTIRQ-unsafe lock order in fasync signaling A SOFTIRQ-safe to SOFTIRQ-unsafe lock order deadlock can occur in send_sigio() and send_sigurg() when a process group receives a signal. When FASYNC is configured for a process group (PIDTYPE_PGID), both functions use read_lock(&tasklist_lock) to traverse the task list. However, they are frequently called from softirq context: - send_sigio() via input_inject_event -> kill_fasync - send_sigurg() via tcp_check_urg -> sk_send_sigurg (NET_RX_SOFTIRQ) The deadlock is caused by the rwlock writer fairness mechanism: 1. CPU 0 (process context) holds read_lock(&tasklist_lock) in do_wait(). 2. CPU 1 (process context) attempts write_lock(&tasklist_lock) in fork() or exit() and spins, which blocks all new readers. 3. CPU 0 is interrupted by a softirq (e.g., TCP URG packet reception). 4. The softirq calls send_sigurg() and attempts to acquire read_lock(&tasklist_lock), deadlocking because CPU 1 is waiting. Since PID hashing and do_each_pid_task() traversals are already RCU-protected, the read_lock on tasklist_lock is no longer strictly required for safe traversal. Fix this by replacing tasklist_lock with rcu_read_lock(), aligning the process group signaling path with the single-PID path. This also mitigates a potential remote denial of service vector via TCP URG packets. Lockdep splat: ===================================================== WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected [...] Chain exists of: &dev->event_lock --> &f_owner->lock --> tasklist_lock Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(tasklist_lock); local_irq_disable(); lock(&dev->event_lock); lock(&f_owner->lock); <Interrupt> lock(&dev->event_lock); *** DEADLOCK ***

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_log: validate MAC header was set before dumping it The fallback path of dump_mac_header() guards the MAC header access only with "skb->mac_header != skb->network_header", without checking skb_mac_header_was_set(). When the MAC header is unset, mac_header is 0xffff, so the test passes and skb_mac_header(skb) returns skb->head + 0xffff, ~64 KiB past the buffer; the loop then reads dev->hard_header_len bytes out of bounds into the kernel log. This is reachable via the netdev logger: nf_log_unknown_packet() calls dump_mac_header() unconditionally, and an skb sent through AF_PACKET with PACKET_QDISC_BYPASS reaches the egress hook with mac_header still unset (__dev_queue_xmit(), which would reset it, is bypassed). Add the skb_mac_header_was_set() check the ARPHRD_ETHER path already uses, and replace the open-coded MAC header length test with skb_mac_header_len(). Only skbs with an unset MAC header are affected; valid ones are dumped as before. BUG: KASAN: slab-out-of-bounds in dump_mac_header (net/netfilter/nf_log_syslog.c:831) Read of size 1 at addr ffff88800ea49d3f by task exploit/148 Call Trace: kasan_report (mm/kasan/report.c:595) dump_mac_header (net/netfilter/nf_log_syslog.c:831) nf_log_netdev_packet (net/netfilter/nf_log_syslog.c:938 net/netfilter/nf_log_syslog.c:963) nf_log_packet (net/netfilter/nf_log.c:260) nft_log_eval (net/netfilter/nft_log.c:60) nft_do_chain (net/netfilter/nf_tables_core.c:285) nft_do_chain_netdev (net/netfilter/nft_chain_filter.c:307) nf_hook_slow (net/netfilter/core.c:619) nf_hook_direct_egress (net/packet/af_packet.c:257) packet_xmit (net/packet/af_packet.c:280) packet_sendmsg (net/packet/af_packet.c:3114) __sys_sendto (net/socket.c:2265)

Linux · Red Hat Enterprise Linux 10 · Red Hat Enterprise Linux 10.0 Extended Update Support · Red Hat Enterprise Linux 7 Extended Lifecycle Support

In the Linux kernel, the following vulnerability has been resolved: ipc: limit next_id allocation to the valid ID range The checkpoint/restore sysctl path can request the next SysV IPC id through ids->next_id. ipc_idr_alloc() currently forwards that request to idr_alloc() with an open-ended upper bound. If the valid tail of the SysV IPC id space is full, the allocation can spill beyond ipc_mni. The returned SysV IPC id still uses the normal index encoding, so later lookup and removal can target the wrong slot. This leaves the real IDR entry behind and breaks the IDR state for the object. The bug is in ipc_idr_alloc() in the checkpoint/restore path. 1. ids->next_id is passed to: idr_alloc(&ids->ipcs_idr, new, ipcid_to_idx(next_id), 0, ...) 2. The zero upper bound makes the allocation effectively open-ended. Once the valid SysV IPC tail is occupied, idr_alloc() can spill past ipc_mni and allocate an entry beyond the valid IPC id range. 3. The new object id is still encoded with the narrower SysV IPC index width: new->id = (new->seq << ipcmni_seq_shift()) + idx 4. Later removal goes through ipc_rmid(), which uses: ipcid_to_idx(ipcp->id) That truncates the real IDR index. An object actually stored at a high index can then be removed as if it lived at a low in-range index. 5. For shared memory, shm_destroy() frees the current object anyway, but the real high IDR slot is left behind as a dangling pointer. 6. A subsequent walk of /proc/sysvipc/shm reaches the stale IDR entry and dereferences freed memory. Prevent this by bounding the requested allocation to ipc_mni so the checkpoint/restore path fails once the valid range is exhausted.

Significant-Gravitas AutoGPT

AutoGPT is a workflow automation platform for creating, deploying, and managing continuous artificial intelligence agents. Versions prior to 0.6.62 have a DOM-based Cross-Site Scripting (XSS) vulnerability in AutoGPT's signup page. The application improperly trusts a URL parameter (`next`), which is passed to `router.push`. An attacker can craft a malicious link that, when opened by an authenticated user, performs a client-side redirect and executes arbitrary JavaScript in the context of their browser. This could lead to credential theft, internal network pivoting, and unauthorized actions performed on behalf of the victim. Version 0.6.62 patches the issue.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem

In the Linux kernel, the following vulnerability has been resolved: flow_dissector: do not dissect PPPoE PFC frames RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT RECOMMENDED for PPPoE. In practice, pppd does not support negotiating PFC for PPPoE sessions, and the flow dissector driver has assumed an uncompressed frame until the blamed commit. During the review process of that commit [1], support for PFC is suggested. However, having a compressed (1-byte) protocol field means the subsequent PPP payload is shifted by one byte, causing 4-byte misalignment for the network header and an unaligned access exception on some architectures. The exception can be reproduced by sending a PPPoE PFC frame to an ethernet interface of a MIPS board, with RPS enabled, even if no PPPoE session is active on that interface: $ 0 : 00000000 80c40000 00000000 85144817 $ 4 : 00000008 00000100 80a75758 81dc9bb8 $ 8 : 00000010 8087ae2c 0000003d 00000000 $12 : 000000e0 00000039 00000000 00000000 $16 : 85043240 80a75758 81dc9bb8 00006488 $20 : 0000002f 00000007 85144810 80a70000 $24 : 81d1bda0 00000000 $28 : 81dc8000 81dc9aa8 00000000 805ead08 Hi : 00009d51 Lo : 2163358a epc : 805e91f0 __skb_flow_dissect+0x1b0/0x1b50 ra : 805ead08 __skb_get_hash_net+0x74/0x12c Status: 11000403 KERNEL EXL IE Cause : 40800010 (ExcCode 04) BadVA : 85144817 PrId : 0001992f (MIPS 1004Kc) Call Trace: [<805e91f0>] __skb_flow_dissect+0x1b0/0x1b50 [<805ead08>] __skb_get_hash_net+0x74/0x12c [<805ef330>] get_rps_cpu+0x1b8/0x3fc [<805fca70>] netif_receive_skb_list_internal+0x324/0x364 [<805fd120>] napi_complete_done+0x68/0x2a4 [<8058de5c>] mtk_napi_rx+0x228/0xfec [<805fd398>] __napi_poll+0x3c/0x1c4 [<805fd754>] napi_threaded_poll_loop+0x234/0x29c [<805fd848>] napi_threaded_poll+0x8c/0xb0 [<80053544>] kthread+0x104/0x12c [<80002bd8>] ret_from_kernel_thread+0x14/0x1c Code: 02d51821 1060045b 00000000 <8c640000> 3084000f 2c820005 144001a2 00042080 8e220000 To reduce the attack surface and maintain performance, do not process PPPoE PFC frames. [1] https://lore.kernel.org/r/20220630231016.GA392@debian.home

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem

In the Linux kernel, the following vulnerability has been resolved: isofs: validate Rock Ridge CE continuation extent against volume size rock_continue() reads rs->cont_extent verbatim from the Rock Ridge CE record and passes it to sb_bread() without checking that the block number is within the mounted ISO 9660 volume. commit e595447e177b ("[PATCH] rock.c: handle corrupted directories") added cont_offset and cont_size rejection for the CE continuation but did not validate the extent block number itself. commit f54e18f1b831 ("isofs: Fix infinite looping over CE entries") later capped the CE chain length at RR_MAX_CE_ENTRIES = 32 but again left the block number unchecked. With a crafted ISO mounted via udisks2 (desktop optical auto-mount) or via CAP_SYS_ADMIN mount, rs->cont_extent can therefore point at an out-of-range block or at blocks belonging to an adjacent filesystem on the same block device. sb_bread() on an out-of-range block returns NULL cleanly via the block layer EIO path, so there is no memory-safety violation. For in-range reads of adjacent- filesystem data, the CE buffer is parsed as Rock Ridge records and only the text of SL sub-records reaches userspace through readlink(), which makes the info-leak channel narrow and difficult to exploit; still, rejecting the malformed CE outright matches the rejection shape already present in the same function for cont_offset and cont_size. Add an ISOFS_SB(sb)->s_nzones bounds check to rock_continue() next to the existing offset/size rejection, printing the same corrupted-directory-entry notice.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: dm: fix a buffer overflow in ioctl processing Tony Asleson (using Claude) found a buffer overflow in dm-ioctl in the function retrieve_status: 1. The code in retrieve_status checks that the output string fits into the output buffer and writes the output string there 2. Then, the code aligns the "outptr" variable to the next 8-byte boundary: outptr = align_ptr(outptr); 3. The alignment doesn't check overflow, so outptr could point past the buffer end 4. The "for" loop is iterated again, it executes: remaining = len - (outptr - outbuf); 5. If "outptr" points past "outbuf + len", the arithmetics wraps around and the variable "remaining" contains unusually high number 6. With "remaining" being high, the code writes more data past the end of the buffer Luckily, this bug has no security implications because: 1. Only root can issue device mapper ioctls 2. The commonly used libraries that communicate with device mapper (libdevmapper and devicemapper-rs) use buffer size that is aligned to 8 bytes - thus, "outptr = align_ptr(outptr)" can't overshoot the input buffer and the bug can't happen accidentally

ARMember Premium – Membership Plugin, Content Restriction, Member Levels, User Profile & User signup

The ARMember Premium plugin for WordPress is vulnerable to SQL Injection via the 'order' parameter of the 'arm_directory_paging_action' AJAX action in all versions up to, and including, 7.3.1. This is due to insufficient escaping on the user-supplied 'order' and 'orderby' parameters and the lack of sufficient preparation on the existing SQL query in the `arm_get_directory_members()` function. This makes it possible for unauthenticated attackers to append additional SQL queries into already existing queries that can be used to extract sensitive information from the database.

Linux · Red Hat Enterprise Linux 10 · Red Hat Enterprise Linux 10.0 Extended Update Support · Red Hat Enterprise Linux 8

In the Linux kernel, the following vulnerability has been resolved: sctp: revalidate list cursor after sctp_sendmsg_to_asoc() in SCTP_SENDALL The SCTP_SENDALL path in sctp_sendmsg() iterates ep->asocs with list_for_each_entry_safe(), which caches the next entry in @tmp before the loop body runs. The body calls sctp_sendmsg_to_asoc(), which may drop the socket lock inside sctp_wait_for_sndbuf(). While the lock is dropped, another thread can SCTP_SOCKOPT_PEELOFF the association cached in @tmp, migrating it to a new endpoint via sctp_sock_migrate() (list_del_init() + list_add_tail() to newep->asocs), and optionally close the new socket which frees the association via kfree_rcu(). The cached @tmp can also be freed by a network ABORT for that association, processed in softirq while the lock is dropped. sctp_wait_for_sndbuf() revalidates @asoc (the current entry) on re-lock via the "sk != asoc->base.sk" and "asoc->base.dead" checks, but nothing revalidates @tmp. After a successful return, the iterator advances to the stale @tmp, yielding either a use-after-free (if the peeled socket was closed) or a list-walk onto the new endpoint's list head (type confusion of &newep->asocs as a struct sctp_association *). Both are reachable from CapEff=0; the type-confusion path gives controlled indirect call via the outqueue.sched->init_sid pointer. Fix by re-deriving @tmp from @asoc after sctp_sendmsg_to_asoc() returns. @asoc is known to still be on ep->asocs at that point: the only callers that list_del an association from ep->asocs are sctp_association_free() (which sets asoc->base.dead) and sctp_assoc_migrate() (which changes asoc->base.sk), and sctp_wait_for_sndbuf() checks both under the lock before any successful return; a tripped check propagates as err < 0 and the loop bails before the re-derive. The SCTP_ABORT path in sctp_sendmsg_check_sflags() returns 0 and the loop hits 'continue' before sctp_sendmsg_to_asoc() is ever called, so the @tmp cached by list_for_each_entry_safe() still covers the lock-held free that ba59fb027307 ("sctp: walk the list of asoc safely") was added for.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: drm/gem: Fix inconsistent plane dimension calculation in drm_gem_fb_init_with_funcs() drm_gem_fb_init_with_funcs() computes sub-sampled plane dimensions using plain integer division: unsigned int width = mode_cmd->width / (i ? info->hsub : 1); unsigned int height = mode_cmd->height / (i ? info->vsub : 1); However, the ioctl-level framebuffer_check() in drm_framebuffer.c uses drm_format_info_plane_width/height() which round up dimensions via DIV_ROUND_UP(). This inconsistency corrupts the subsequent GEM object size check for certain pixel format and dimension combinations. For example, with NV12 (vsub=2) and a 1-pixel-tall framebuffer the GEM size validation path sees height=0 instead of height=1. The expression (height - 1) then wraps to UINT_MAX as an unsigned int, causing min_size to overflow and wrap back to a small value. A tiny GEM object therefore passes the size guard, yet when the GPU accesses the chroma plane it will read or write memory beyond the object's bounds. Fix by replacing the open-coded divisions with drm_format_info_plane_width() and drm_format_info_plane_height(), which use DIV_ROUND_UP() and match the calculation already used in framebuffer_check().

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: mtd: spi-nor: debugfs: fix out-of-bounds read in spi_nor_params_show() Sashiko noticed an out-of-bounds read [1]. In spi_nor_params_show(), the snor_f_names array is passed to spi_nor_print_flags() using sizeof(snor_f_names). Since snor_f_names is an array of pointers, sizeof() returns the total number of bytes occupied by the pointers (element_count * sizeof(void *)) rather than the element count itself. On 64-bit systems, this makes the passed length 8x larger than intended. Inside spi_nor_print_flags(), the 'names_len' argument is used to bounds-check the 'names' array access. An out-of-bounds read occurs if a flag bit is set that exceeds the array's actual element count but is within the inflated byte-size count. Correct this by using ARRAY_SIZE() to pass the actual number of string pointers in the array.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ipmi: Add limits to event and receive message requests The driver would just fetch events and receive messages until the BMC said it was done. To avoid issues with BMCs that never say they are done, add a limit of 10 fetches at a time. In addition, an si interface has an attn state it can return from the hardware which is supposed to cause a flag fetch to see if the driver needs to fetch events or message or a few other things. If the attn bit gets stuck, it's a similar problem. So allow messages in between flag fetches so the driver itself doesn't get stuck. This is a more general fix than the previous fix for the specific bad BMC, but should fix the more general issue of a BMC that won't stop saying it has data. This has been there from the beginning of the driver. It's not a bug per-se, but it is accounting for bugs in BMCs.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: scsi: target: configfs: Bound snprintf() return in tg_pt_gp_members_show() target_tg_pt_gp_members_show() formats LUN paths with snprintf() into a 256-byte stack buffer, then will memcpy() cur_len bytes from that buffer. snprintf() returns the length the output would have had, which can exceed the buffer size when the fabric WWN is long because iSCSI IQN names can be up to 223 bytes. The check at the memcpy() site only guards the destination page write, not the source read, so memcpy() will read past the stack buffer and copy adjacent stack contents to the sysfs reader, which when CONFIG_FORTIFY_SOURCE is enabled, fortify_panic() will be triggered. Commit 27e06650a5ea ("scsi: target: target_core_configfs: Add length check to avoid buffer overflow") added the same bound to the target_lu_gp_members_show() but the tg_pt_gp variant was missed so resolve that here.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921: fix a potential clc buffer length underflow The buf_len is used to limit the iterations for retrieving the country power setting and may underflow under certain conditions due to changes in the power table in CLC. This underflow leads to an almost infinite loop or an invalid power setting resulting in driver initialization failure.

Linux · Red Hat Enterprise Linux 10 · Red Hat Enterprise Linux 10.0 Extended Update Support · Red Hat Enterprise Linux 7 Extended Lifecycle Support

In the Linux kernel, the following vulnerability has been resolved: xfrm: defensively unhash xfrm_state lists in __xfrm_state_delete KASAN reproduces a slab-use-after-free in __xfrm_state_delete()'s hlist_del_rcu calls under syzkaller load on linux-6.12.y stable (reproduced on 6.12.47, also reachable via the same code path on torvalds/master and on the ipsec tree). Nine unique signatures cluster in the xfrm_state lifecycle, the load-bearing one being: BUG: KASAN: slab-use-after-free in __hlist_del include/linux/list.h:990 [inline] BUG: KASAN: slab-use-after-free in hlist_del_rcu include/linux/rculist.h:516 [inline] BUG: KASAN: slab-use-after-free in __xfrm_state_delete net/xfrm/xfrm_state.c Write of size 8 at addr ffff8881198bcb70 by task kworker/u8:9/435 Workqueue: netns cleanup_net Call Trace: __hlist_del / hlist_del_rcu __xfrm_state_delete xfrm_state_delete xfrm_state_flush xfrm_state_fini ops_exit_list cleanup_net The other observed signatures hit the same slab object from __xfrm_state_lookup, xfrm_alloc_spi, __xfrm_state_insert and an OOB write variant of __xfrm_state_delete, all on the byseq/byspi hash chains. __xfrm_state_delete() guards its byseq and byspi unhashes with value-based predicates: if (x->km.seq) hlist_del_rcu(&x->byseq); if (x->id.spi) hlist_del_rcu(&x->byspi); while everywhere else in the file (e.g. state_cache, state_cache_input) the safer hlist_unhashed() check is used. xfrm_alloc_spi() sets x->id.spi = newspi inside xfrm_state_lock and then immediately inserts into byspi, but a path that observes x->id.spi != 0 outside of xfrm_state_lock can still skip-or-hit the byspi unhash inconsistently with whether x is actually on the list. The same holds for x->km.seq versus byseq, and the bydst/bysrc unhashes have no predicate at all, so a second __xfrm_state_delete() on the same object writes through LIST_POISON pprev. The defensive change here: - Use hlist_del_init_rcu() instead of hlist_del_rcu() on bydst, bysrc, byseq and byspi so a second deletion is a no-op rather than a write through LIST_POISON pprev. The byseq/byspi nodes are already initialised in xfrm_state_alloc(). - Test hlist_unhashed() rather than the value predicate for byseq/byspi, so the unhash decision tracks list state rather than mutable scalar fields. Empirical verification: applied this patch on top of v6.12.47, rebuilt, and re-ran the same syzkaller harness for 1h16m on a previously-crashy configuration that produced ~100 hits each of slab-use-after-free Read in xfrm_alloc_spi / Read in __xfrm_state_lookup / Write in __xfrm_state_delete. After the patch, 7.1M execs across 32 VMs at ~1550 exec/sec produced zero xfrm_state UAF/OOB hits. /proc/slabinfo confirms the xfrm_state slab is actively allocated and freed during the run (~143 KiB resident), so the fuzzer is still exercising those code paths -- they just no longer crash. Reproduction: - Linux 6.12.47 x86_64 + KASAN_GENERIC + KASAN_INLINE + KCOV - syzkaller @ 746545b8b1e4c3a128db8652b340d3df90ce61db - 32 QEMU/KVM VMs x 2 vCPU on AWS c5.metal bare metal - 9 unique signatures collected in ~9h, all within xfrm_state lifecycle

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Fix shadow paging use-after-free due to unexpected GFN The shadow MMU computes GFNs for direct shadow pages using sp->gfn plus the SPTE index. This assumption breaks for shadow paging if the guest page tables are modified between VM entries (similar to commit aad885e77496, "KVM: x86/mmu: Drop/zap existing present SPTE even when creating an MMIO SPTE", 2026-03-27). The flow is as follows: - a PDE is installed for a 2MB mapping, and a page in that area is accessed. KVM creates a kvm_mmu_page consisting of 512 4KB pages; the kvm_mmu_page is marked by FNAME(fetch) as direct-mapped because the guest's mapping is a huge page (and thus contiguous). - the PDE mapping is changed from outside the guest. - the guest accesses another page in the same 2MB area. KVM installs a new leaf SPTE and rmap entry; the SPTE uses the "correct" GFN (i.e. based on the new mapping, as changed in the previous step) but that GFN is outside of the [sp->gfn, sp->gfn + 511] range; therefore the rmap entry cannot be found and removed when the kvm_mmu_page is zapped. - the memslot that covers the first 2MB mapping is deleted, and the kvm_mmu_page for the now-invalid GPA is zapped. However, rmap_remove() only looks at the [sp->gfn, sp->gfn + 511] range established in step 1, and fails to find the rmap entry that was recorded by step 3. - any operation that causes an rmap walk for the same page accessed by step 3 then walks a stale rmap and dereferences a freed kvm_mmu_page. This includes dirty logging or MMU notifier invalidations (e.g., from MADV_DONTNEED). The underlying issue is that KVM's walking of shadow PTEs assumes that if a SPTE is present when KVM wants to install a non-leaf SPTE, then the existing kvm_mmu_page must be for the correct gfn. Because the only way for the gfn to be wrong is if KVM messed up and failed to zap a SPTE... which shouldn't happen, but *actually* only happens in response to a guest write. That bug dates back literally forever, as even the first version of KVM assumes that the GFN matches and walks into the "wrong" shadow page. However, that was only an imprecision until 2032a93d66fa ("KVM: MMU: Don't allocate gfns page for direct mmu pages") came along. Fix it by checking for a target gfn mismatch and zapping the existing SPTE. That way the old SP and rmap entries are gone, KVM installs the rmap in the right location, and everyone is happy.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: Prevent NULL deref when RX memory exhausted The CPU receives frames from the MAC through conventional DMA: the CPU allocates buffers for the MAC, then the MAC fills them and returns ownership to the CPU. For each hardware RX queue, the CPU and MAC coordinate through a shared ring array of DMA descriptors: one descriptor per DMA buffer. Each descriptor includes the buffer's physical address and a status flag ("OWN") indicating which side owns the buffer: OWN=0 for CPU, OWN=1 for MAC. The CPU is only allowed to set the flag and the MAC is only allowed to clear it, and both must move through the ring in sequence: thus the ring is used for both "submissions" and "completions." In the stmmac driver, stmmac_rx() bookmarks its position in the ring with the `cur_rx` index. The main receive loop in that function checks for rx_descs[cur_rx].own=0, gives the corresponding buffer to the network stack (NULLing the pointer), and increments `cur_rx` modulo the ring size. After the loop exits, stmmac_rx_refill(), which bookmarks its position with `dirty_rx`, allocates fresh buffers and rearms the descriptors (setting OWN=1). If it fails any allocation, it simply stops early (leaving OWN=0) and will retry where it left off when next called. This means descriptors have a three-stage lifecycle (terms my own): - `empty` (OWN=1, buffer valid) - `full` (OWN=0, buffer valid and populated) - `dirty` (OWN=0, buffer NULL) But because stmmac_rx() only checks OWN, it confuses `full`/`dirty`. In the past (see 'Fixes:'), there was a bug where the loop could cycle `cur_rx` all the way back to the first descriptor it dirtied, resulting in a NULL dereference when mistaken for `full`. The aforementioned commit resolved that *specific* failure by capping the loop's iteration limit at `dma_rx_size - 1`, but this is only a partial fix: if the previous stmmac_rx_refill() didn't complete, then there are leftover `dirty` descriptors that the loop might encounter without needing to cycle fully around. The current code therefore panics (see 'Closes:') when stmmac_rx_refill() is memory-starved long enough for `cur_rx` to catch up to `dirty_rx`. Fix this by explicitly checking, before advancing `cur_rx`, if the next entry is dirty; exit the loop if so. This prevents processing of the final, used descriptor until stmmac_rx_refill() succeeds, but fully prevents the `cur_rx == dirty_rx` ambiguity as the previous bugfix intended: so remove the clamp as well. Since stmmac_rx_zc() is a copy-paste-and-tweak of stmmac_rx() and the code structure is identical, any fix to stmmac_rx() will also need a corresponding fix for stmmac_rx_zc(). Therefore, apply the same check there. In stmmac_rx() (not stmmac_rx_zc()), a related bug remains: after the MAC sets OWN=0 on the final descriptor, it will be unable to send any further DMA-complete IRQs until it's given more `empty` descriptors. Currently, the driver simply *hopes* that the next stmmac_rx_refill() succeeds, risking an indefinite stall of the receive process if not. But this is not a regression, so it can be addressed in a future change.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: dm-thin: fix metadata refcount underflow There's a bug in dm-thin in the function rebalance_children. If the internal btree node has one entry, the code tries to copy all btree entries from the node's child to the node itself and then decrement the child's reference count. If the child node is shared (it has reference count > 1), we won't free it, so there would be two pointers to each of the grandchildren nodes. But the reference counts of the grandchildren is not increased, thus the reference count doesn't match the number of pointers that point to the grandchildren. This results in "device mapper: space map common: unable to decrement block" errors. Fix this bug by incrementing reference counts on the grandchildren if the btree node is shared.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: net: strparser: fix skb_head leak in strp_abort_strp() When the stream parser is aborted, for example after a message assembly timeout, it can still hold a reference to a partially assembled message in strp->skb_head. That skb is not released in strp_abort_strp(), which leaks the partially assembled message and can be triggered repeatedly to exhaust memory. Fix this by freeing strp->skb_head and resetting the parser state in the abort path. Leave strp_stop() unchanged so final cleanup still happens in strp_done() after the work and timer have been synchronized.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: fbdev: defio: Disconnect deferred I/O from the lifetime of struct fb_info Hold state of deferred I/O in struct fb_deferred_io_state. Allocate an instance as part of initializing deferred I/O and remove it only after the final mapping has been closed. If the fb_info and the contained deferred I/O meanwhile goes away, clear struct fb_deferred_io_state.info to invalidate the mapping. Any access will then result in a SIGBUS signal. Fixes a long-standing problem, where a device hot-unplug happens while user space still has an active mapping of the graphics memory. The hot- unplug frees the instance of struct fb_info. Accessing the memory will operate on undefined state.

Linux · Red Hat Enterprise Linux 10 · Red Hat Enterprise Linux 6 · Red Hat Enterprise Linux 7

In the Linux kernel, the following vulnerability has been resolved: crypto: authencesn - reject short ahash digests during instance creation authencesn requires either a zero authsize or an authsize of at least 4 bytes because the ESN encrypt/decrypt paths always move 4 bytes of high-order sequence number data at the end of the authenticated data. While crypto_authenc_esn_setauthsize() already rejects explicit non-zero authsizes in the range 1..3, crypto_authenc_esn_create() still copied auth->digestsize into inst->alg.maxauthsize without validating it. The AEAD core then initialized the tfm's default authsize from that value. As a result, selecting an ahash with digest size 1..3, such as cbcmac(cipher_null), exposed authencesn instances whose default authsize was invalid even though setauthsize() would have rejected the same value. AF_ALG could then trigger the ESN tail handling with a too-short tag and hit an out-of-bounds access. Reject authencesn instances whose ahash digest size is in the invalid non-zero range 1..3 so that no tfm can inherit an unsupported default authsize.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: misc: ibmasm: fix OOB MMIO read in ibmasm_handle_mouse_interrupt() ibmasm_handle_mouse_interrupt() performs an out-of-bounds MMIO read when the queue reader or writer index from hardware exceeds REMOTE_QUEUE_SIZE (60). A compromised service processor can trigger this by writing an out-of-range value to the reader or writer MMIO register before asserting an interrupt. Since writer is re-read from hardware on every loop iteration, it can also be set to an out-of-range value after the loop has already started. The root cause is that get_queue_reader() and get_queue_writer() return raw readl() values that are passed directly into get_queue_entry(), which computes: queue_begin + reader * sizeof(struct remote_input) with no bounds check. This unchecked MMIO address is then passed to memcpy_fromio(), reading 8 bytes from unintended device registers. For sufficiently large values the address falls outside the PCI BAR mapping entirely, triggering a machine check exception. Fix by checking both indices against REMOTE_QUEUE_SIZE at the top of the loop body, before any call to get_queue_entry(). On an out-of-range value, reset the reader register to 0 via set_queue_reader() before breaking, so that normal queue operation can resume if the corrupted hardware state is transient.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: slip: bound decode() reads against the compressed packet length slhc_uncompress() parses a VJ-compressed TCP header by advancing a pointer through the packet via decode() and pull16(). Neither helper bounds-checks against isize, and decode() masks its return with & 0xffff so it can never return the -1 that callers test for -- those error paths are dead code. A short compressed frame whose change byte requests optional fields lets decode() read past the end of the packet. The over-read bytes are folded into the cached cstate and reflected into subsequent reconstructed packets. Make decode() and pull16() take the packet end pointer and return -1 when exhausted. Add a bounds check before the TCP-checksum read. The existing == -1 tests now do what they were always meant to.

GNU libredwg

A flaw has been found in GNU libredwg up to 0.13.4.8160. This issue affects the function bit_read_RC of the file bits.c of the component Dwgbmp Utility. This manipulation causes heap-based buffer overflow. The attack is possible to be carried out remotely. The exploit has been published and may be used. Patch name: 8f03865f37f5d4ffd616fef802acc980be54d300. Applying a patch is the recommended action to fix this issue.