Recherche « Date ical project date ical »

zephyrproject zephyr

The Nuvoton NPCX eSPI driver parses Target-Attached-Flash (TAF) requests in espi_taf_parse() (drivers/espi/espi_npcx.c), taking the 12-bit length field directly out of the request header in the FLASHRXBUF FIFO. For write and RPMC OP1 requests it copied DIV_ROUND_UP(len, 4) words into struct espi_taf_pckt.src, a fixed 16-word (64-byte) member of a static structure, without ever comparing the length against that buffer or against the negotiated eSPI receive payload size (rx-plsize, 64 bytes on all in-tree NPCX/NPCK SoCs). Both the loop counter and the word count were uint8_t, so the copy ran up to 255 iterations. An eSPI controller that emits a flash request whose header claims a payload larger than the negotiated maximum therefore drives up to 239 32-bit stores past the end of the structure — roughly 956 bytes of out-of-bounds write into .bss — from the eSPI flash receive interrupt handler, while the source reads walk past the end of the 18-word FLASHRXBUF register array into neighbouring eSPI registers. The same unvalidated length was then passed on to flash_write() in espi_taf_npcx_flash_write() with the 64-byte src buffer as source, reading up to 4 KB of adjacent controller SRAM into SPI flash at a host-chosen address, where the host can read it back. A related fixed-size stack buffer in taf_npcx_completion_handler() was overflowed by four bytes on the maximum-size completion path on SoCs whose tx-plsize is 64. The defect is reachable only from the eSPI host side, and only by a request that violates the negotiated payload size, so it requires host firmware or bus-level control rather than ordinary host software; a compliant maximum-length write fits the buffer exactly and is handled correctly. Because TAF exists specifically so that the embedded controller arbitrates host access to shared flash (espi_taf_check_read_protect() / espi_taf_check_write_protect()), corrupting controller memory from a host-supplied field crosses the trust boundary the feature asserts; consequences range from controller crash or hang to corruption of driver state that gates the flash protection regions. The fix widens the counters, rejects any request whose word count exceeds both ARRAY_SIZE(FLASHRXBUF) - NPCX_ESPI_FLASH_HEADER_ADDRESS_LEN and NPCX_TAF_RX_PAYLOAD_WORDS (derived from the devicetree rx-plsize), marks such packets with a new invalid_flag so espi_taf_work() answers them with an unsuccessful completion instead of processing them, bounds the transmit payload against FLASHTXBUF, and adds a default case for unsupported cycle types. Only configurations with CONFIG_ESPI_TAF enabled on an NPCX/NPCK target are affected; no in-tree board enables it by default.

Oracle Corporation Primavera P6 Enterprise Project Portfolio Management

Vulnerability in the Primavera P6 Enterprise Project Portfolio Management product of Oracle Construction and Engineering (component: Web Access). Supported versions that are affected are 21.12.0.0-21.12.21.9, 22.12.0.0-22.12.21.4, 23.12.0-23.12.20, 24.12.0-24.12.16 and 25.12.0-25.12.8. Difficult to exploit vulnerability allows low privileged attacker with network access via HTTP to compromise Primavera P6 Enterprise Project Portfolio Management. Successful attacks require human interaction from a person other than the attacker and while the vulnerability is in Primavera P6 Enterprise Project Portfolio Management, attacks may significantly impact additional products (scope change). Successful attacks of this vulnerability can result in unauthorized access to critical data or complete access to all Primavera P6 Enterprise Project Portfolio Management accessible data as well as unauthorized update, insert or delete access to some of Primavera P6 Enterprise Project Portfolio Management accessible data. CVSS 3.1 Base Score 6.5 (Confidentiality and Integrity impacts). CVSS Vector: (CVSS:3.1/AV:N/AC:H/PR:L/UI:R/S:C/C:H/I:L/A:N).

Ultralytics FastSAM

A weakness has been identified in Ultralytics FastSAM up to b4ed20c2fed75eadc5aa7d8b09fedd137b873b52. This affects the function session.get_modelmeta.custom_metadata_map of the file ultralytics/nn/autobackend.py of the component AutoBackend Model Loading. This manipulation of the argument imgsz/names/kpt_shape causes improper neutralization of directives in dynamically evaluated code. The attack requires local access. This product uses a rolling release model to deliver continuous updates. As a result, specific version information for affected or updated releases is not available. The project was informed of the problem early through an issue report but has not responded yet.

zephyrproject zephyr

The CC1200 sub-GHz IEEE 802.15.4 driver takes the PHY packet length from the first byte of the radio's RX FIFO in get_packet_length() and validates it in verify_rxfifo_validity() (drivers/ieee802154/ieee802154_cc1200.c). That validation only enforced a lower bound (pkt_len < 3); its second clause rejects a FIFO that holds more bytes than declared and therefore never bounds large values. Because the driver configures the radio for variable packet length with PKT_LEN = 0xFF, the length byte is an over-the-air value of 0-255 that reached net_pkt_rx_alloc_with_buffer() and the subsequent SPI burst read unclamped. An unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip's 128-byte RX FIFO has not overflowed, so the driver's RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required. With the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment's buf->data and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected.

code-projects Online Reviewer System

A vulnerability has been found in code-projects Online Reviewer System 1.0. This vulnerability affects unknown code of the file /reviewer/system/system/admins/manage/users/btn_functions.php of the component User Profile Update Handler. The manipulation of the argument usertype_id leads to dynamically-determined object attributes. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used.

zephyrproject zephyr

The Link Layer Control Procedure (LLCP) implementation of the Zephyr software Bluetooth LE Controller retains the receive node that carried an accepted LL_PHY_UPDATE_IND so that it can later be reused for the host notification when the update instant is reached (llcp_rx_node_retain() in subsys/bluetooth/controller/ll_sw/ull_llcp.c, and the node is deliberately not recycled while marked NODE_RX_TYPE_RETAIN). The invalid-PDU arms of llcp_lp_pu_rx() and llcp_rp_pu_rx() in subsys/bluetooth/controller/ll_sw/ull_llcp_phy.c completed the procedure via llcp_lr_complete() / llcp_rr_complete() without first releasing that retained node, so the procedure context — the only remaining reference to the node — was freed while the node was still held out of the receive pool. A peer device on an established LE connection can drive this deterministically and without pairing or encryption. Against a peripheral it sends LL_PHY_REQ, receives LL_PHY_RSP, sends a valid LL_PHY_UPDATE_IND with an instant a few connection events in the future (so the node becomes retained), and then, before the instant is reached, sends any other LL Control PDU such as LL_LENGTH_REQ; ull_cp_rx() routes it to the active remote PHY Update procedure, which takes the invalid-PDU path. The mirror case applies to a locally initiated PHY Update followed by an LL_REJECT_IND. In the default configuration (CONFIG_BT_ASSERT and CONFIG_BT_CTLR_ASSERT_DEBUG both default y) the violated invariant in llcp_lr_check_done() / llcp_rr_check_done() triggers a controller assertion, ending in k_oops() (or k_panic()) — a single crafted PDU sequence from radio range faults the device. With those assertions compiled out, each attempt silently leaks one receive PDU node and its memq link; because the controller receive pool is small (PDU_RX_CNT, driven by CONFIG_BT_CTLR_RX_BUFFERS, which defaults to 1) and each attempt costs the attacker only a reconnect, a few repetitions exhaust the pool and leave Bluetooth inoperable until reboot. On releases v3.4.0 through v3.7.x the assertion is never reached, whatever the configuration, so every attempt leaks silently. The impact is limited to availability: the orphaned node leaves no dangling pointer that is later dereferenced and is never delivered to the host, so there is no memory corruption or information disclosure. The same pull request applies the identical release to the Connection Update and CIS-create procedures, whose invalid-PDU arms had the same omission.

zephyrproject zephyr

The Bluetooth Link Layer control procedure code in subsys/bluetooth/controller/ll_sw/ull_llcp_conn_upd.c retains the received RX node while a Connection Update / Connection Parameter procedure waits for its instant, so the node can later carry the host notification (llcp_rx_node_retain(), which marks it NODE_RX_TYPE_RETAIN and thereby suppresses the normal recycling in ull.c). The default: arm of llcp_rp_cu_rx() and llcp_lp_cu_rx() — the "invalid PDU, terminate the connection" path — completed the procedure without releasing that retained node. llcp_rr_check_done() then dequeued and freed the procedure context with ctx->node_ref.rx still pointing at the retained node, dropping the last reference to it. A peer device in radio range can reach this without pairing, bonding, or encryption. Against a peripheral, the peer sends a well-formed LL_CONNECTION_UPDATE_IND with an instant a few connection events in the future (the node is retained and the procedure enters RP_CU_STATE_WAIT_INSTANT), then, before the instant is reached, sends any other LL Control PDU such as LL_LENGTH_REQ. ull_cp_rx() routes that PDU into the active remote Connection Update procedure, which takes the invalid-PDU path. The central role is reachable symmetrically after accepting an LL_CONNECTION_PARAM_REQ, and the local-procedure variant is reachable with LL_REJECT_IND. With CONFIG_BT_CTLR_ASSERT_DEBUG enabled (its default), the resulting state violates the invariant asserted in llcp_rr_check_done(), so the two-PDU sequence produces an immediate fatal error in the controller. With those asserts disabled, each occurrence permanently loses one node from the controller's small fixed RX pool (sized from CONFIG_BT_CTLR_RX_BUFFERS, which defaults to 1); repeating the sequence across reconnections exhausts the pool, after which the link-layer receive path operates on a NULL node. The impact is an unauthenticated, remotely triggerable denial of service persisting until reboot; there is no memory-disclosure or memory-corruption consequence, since the leaked node simply becomes unreachable.

zephyrproject zephyr

The ITE IT8xxx2 SHI host-command backend (subsys/mgmt/ec_host_cmd/backends/ec_host_cmd_backend_shi_ite.c) copied the 8-byte host-command request header from the SPI Rx FIFO directly into the shared receive buffer data->in_msg and only afterwards checked the protocol version and the derived packet length. The interrupt handler also accepted a chip-select assertion and an Rx-valid-length (RVLI) interrupt in any driver state other than SHI_STATE_DISABLED, so a new header could be parsed while the host-command thread was still processing the previous request out of the very same buffer. The host processor is the SPI controller and drives both chip select and the clock. After sending a well-formed request it can immediately de-assert chip select — which returns the driver to the ready state and re-enables the FIFO — and start a second transaction carrying a header with data_len = 0xFFFF. Those eight bytes are written into in_msg before the oversized length is rejected, so they land in a buffer whose contents verify_rx() in subsys/mgmt/ec_host_cmd/ec_host_cmd_handler.c has already validated. If this lands in the window before the host-command thread executes args.input_buf_size = rx_header->data_len, the framework hands the registered command handler a 65535-byte input length over a 256-byte buffer. The result is an out-of-bounds read of up to roughly 64 KiB beyond the request buffer: command handlers that copy or echo input_buf_size bytes disclose adjacent embedded-controller memory back to the host or overflow the response buffer, and a read past the end of SRAM faults the controller. The same race also allows cmd_id and cmd_ver to be swapped after checksum verification and after handler lookup. Exploitation requires the ability to drive the inter-processor SHI bus (a compromised host OS or physical access to the SPI lines) and winning a timing race, which the SPI controller can retry indefinitely. The fix parses the header into a local struct ec_host_cmd_request_header and copies it into in_msg only after the length has been bounded by sizeof(data->in_msg), and ignores chip-select and RVLI interrupts outside SHI_STATE_READY_TO_RECV/SHI_STATE_RECEIVING. A residual, bounded race remains: an end-of-transaction interrupt still resets the state to ready while the host-command thread owns the buffer, so a valid second request can still overwrite the in-flight request's contents, unlike the NPCX backend which parks in SHI_STATE_CNL_RESP_NOT_RDY while the buffer is in use.

Jeebase

A vulnerability was determined in Jeebase 0.0.1. This vulnerability affects the function updateUser of the file /user/update/info of the component UserService. Executing a manipulation of the argument user/tempUser can lead to dynamically-determined object attributes. The attack can be executed remotely. The exploit has been publicly disclosed and may be utilized. The project was informed of the problem early through an issue report but has not responded yet.

zephyrproject zephyr

ieee802154_send() in subsys/net/l2/ieee802154/ieee802154.c copies the outgoing packet into a single fixed 125-byte transmit buffer (tx_frame_buf_pool, sized IEEE802154_MTU). In builds with CONFIG_NET_L2_IEEE802154_FRAGMENT enabled (the default whenever CONFIG_NET_6LO is set), the branch taken when 6LoWPAN fragmentation is not required performed an unchecked net_buf_add_mem(frame_buf, pkt_buf->data, pkt_buf->len). The only guard was __ASSERT_NO_MSG() inside net_buf_simple_add(), which is compiled out without CONFIG_ASSERT, so an oversized packet silently overran the frame buffer. The defect is not reachable from the radio: for NET_AF_INET6 packets ieee802154_6lo_encode_pkt() compares the whole packet length against IEEE802154_MTU and takes the fragmentation path when it does not fit, so every buffer copied on the unfragmented branch is within bounds. It is reachable through NET_AF_PACKET sockets bound to an 802.15.4 interface: for NET_SOCK_RAW the 6LoWPAN block is skipped entirely and for NET_SOCK_DGRAM it returns early on the address-family test, leaving no length validation anywhere on the transmit path (net_context_sendto() and net_if_tx() apply none, and pkt_buffer_length() does not clamp the allocation for this L2). An application — or, in a CONFIG_USERSPACE build, an unprivileged application thread using the zsock_socket()/zsock_sendto() syscalls — can therefore drive a supervisor-mode out-of-bounds write of chosen bytes past the 125-byte pool buffer. With the default CONFIG_NET_BUF_FIXED_DATA_SIZE of 128 bytes the overrun is bounded to roughly ll_hdr_len + 3 bytes; with CONFIG_NET_BUF_VARIABLE_DATA_SIZE a single storage buffer can be as large as CONFIG_NET_PKT_BUF_TX_DATA_POOL_SIZE, making the overrun far larger. The consequence is corruption of memory adjacent to the pool, with a crash or further compromise of kernel state as the practical impact. The fix validates ll_hdr_len + net_pkt_get_len(pkt) + authtag_len against IEEE802154_MTU before any copy and adds a tailroom-checking copy_pkt_to_frame() helper that returns -EMSGSIZE instead of overrunning the buffer. The same change also linearizes the whole net_buf chain into one MAC frame, so packet storage boundaries no longer become frame boundaries on the wire.

ash-project ash

Improperly Controlled Modification of Dynamically-Determined Object Attributes vulnerability in ash-project ash allows a user to set the value of a private action argument on the bulk destroy and bulk update paths. Action arguments declared with public?: false are meant to be set only by trusted server-side code (for example via Ash.Changeset.set_private_argument/3) and must not be settable from end-user input. CVE-2026-55736 fixed the non-bulk changeset path to strip private arguments from user-supplied parameter maps, but the bulk destroy and bulk update paths were not covered. Ash.Actions.Destroy.Bulk.base_changeset/5 and Ash.Actions.Update.Bulk.base_changeset/5 match every key in the caller-supplied parameter map against all of the action's arguments with no public? check, then apply the matches to the base changeset. A caller who can submit parameters to a bulk destroy or bulk update action (for example through AshJsonApi, AshGraphql, or a controller that forwards request parameters to Ash.bulk_destroy/4 or Ash.bulk_update/4) can therefore set any private argument of that action, including one referenced by an arg(...) template in the action's changes or validations. Depending on how the application uses the argument (for example an acting_user_id driving authorization or record ownership, or audit metadata), this can lead to an integrity violation or privilege escalation. The fix requires public? in the argument matching on both bulk paths; private arguments remain settable server-side via the :private_arguments option. This issue affects ash: from 2.17.15 before 3.33.11.

kimai

Kimai is an open-source time tracking application. Prior to 2.58.0, PATCH /api/timesheets/{id}/restart, PATCH /api/timesheets/{id}/duplicate, and the web duplicate workflow can derive a new record from an owned historical timesheet after the user's access to its project or activity has been revoked. TimesheetVoter evaluates the own-timesheet permission before current team access, and its canStart() logic validates object visibility but does not verify the user's current team access to the referenced project and activity. An old entry therefore acts as a persistent capability to create new time records under an unauthorized project and activity, corrupting budgets, statistics, reports, and invoices after an administrative revocation. This issue is fixed in version 2.58.0.

zitadel

ZITADEL is an open source identity management platform. Prior to version 4.16.0, a bug in how ZITADEL updates permissions when multiple project roles are deleted at the same time can cause some user permissions to be missed. This issue specifically affects User Grants on Granted Projects (projects shared between different organizations), potentially allowing users to keep access rights that were supposed to be completely removed. This issue has been fully resolved in version 4.16.0. There are no configuration workarounds. Upgrading to a patched version is the only way to trigger the automatic cleanup migration. Those who cannot upgrade immediately should manually review user permissions specifically for Granted Projects where multiple roles were recently deleted.

cosmicstack-labs mercury-agent

A vulnerability was detected in cosmicstack-labs mercury-agent up to 1.1.13. Affected is the function checkShellCommand of the file src/capabilities/permissions.ts of the component Shell Command Execution. The manipulation results in incorrect behavior order: validate before canonicalize. The attack may be launched remotely. The exploit is now public and may be used. The project was informed of the problem early through an issue report but has not responded yet.

zephyrproject zephyr

The Zephyr SDIO subsystem function sdio_io_rw_extended_helper() in subsys/sd/sdio.c finishes transfers with a byte-I/O loop that uses size = MIN(remaining, func->cis.max_blk_size) as the per-iteration step. The value func->cis.max_blk_size is decoded directly from the SDIO card's CIS FUNCE tuple in sdio_decode_cis() and is not validated. When a card reports a maximum block size of zero, size is always 0, remaining never decreases, and the loop spins forever. The loop is reached from the public SDIO client API used by drivers, including sdio_read_fifo(), sdio_write_fifo(), and the incrementing register read/write helpers, each of which enters the loop while holding the per-card mutex func->card->lock. A card advertising max_blk_size == 0 therefore hangs the calling thread permanently on its first non-block-aligned transfer and never releases the mutex, denying service to the SDIO peripheral (and any subsystem such as Wi-Fi that depends on it) until the device is reset. The malicious value must come from the SDIO card itself, so the defect is exploitable where a removable SDIO/combo card slot lets an attacker insert a crafted or malfunctioning card (a physical attack vector); on boards with a soldered SDIO peripheral it is not attacker-influenceable. There is no memory-safety, confidentiality, or integrity impact — only a permanent availability loss. The fix returns -EIO when func->cis.max_blk_size is zero, before the loop is entered.

Apache Software Foundation Apache Storm Nimbus

Description Nimbus accepted the `uploadedJarLocation` argument of `submitTopology` / `submitTopologyWithOpts` as a server-side path and opened it directly, without checking that it referred to a file the caller had actually uploaded. The intended flow is that a client first calls `beginFileUpload`, which returns a path inside the Nimbus inbox, and uploads the jar in chunks to that location; nothing bound submission to that flow, and the `uploaders` map populated by `beginFileUpload` was never consulted at submit time. An authenticated user with topology submission rights could therefore submit any path readable by the Nimbus daemon user as their topology jar. Nimbus copied the file into the topology's jar blob, and the blob ACL grants the submitting subject read access, so the contents could then be retrieved with the ordinary blob download RPCs. Candidate targets include the Nimbus Kerberos keytab, Thrift and UI TLS private keys, and `storm.yaml` with the ZooKeeper authentication payload. Possession of the Nimbus keytab turns an ordinary tenant into a cluster administrator. In a deployment configured as the documentation recommends, submission is available to every authenticated principal when `nimbus.users` is unset, so no elevated privilege is required. Mitigation Upgrade to 3.1.0, where the submitted location is canonicalised and must resolve inside the Nimbus inbox. Users who cannot upgrade immediately should restrict topology submission to trusted principals via `nimbus.users` or `nimbus.groups`, and should treat any file readable by the Nimbus daemon user as potentially exposed to submitters: rotate the Nimbus keytab and any TLS private keys or ZooKeeper credentials reachable from that account. Local mode is unaffected. Credit Independently reported to the Apache Storm PMC by n0mi1k, with a proof of concept. Also found by the ASF using Claude agents to study the security of open-source projects, validated and reported by Apache Storm.

kimdre doco-cd

Doco-CD is a GitOps continuous delivery tool that automatically deploys and updates Docker Compose projects/services and Swarm stacks. Prior to version 0.90.1, a trust-boundary flaw in OCI artifact verification allowed artifact-provided deployment config to influence the policy used to verify that same artifact. When global OCI signature verification was enabled via `OCI_TRUST_POLICY` (`enabled: true`), an attacker with write access to the configured OCI tag could publish an unsigned or improperly signed artifact containing `.doco-cd.yml` with `oci.verify: false`. This could cause signature verification to be bypassed and untrusted deployment content to be applied. This primarily impacts users deploying from OCI artifacts where deployment config is read from artifact contents (for example, poll/webhook flows without trusted inline deployment overrides). The issue is fixed by enforcing a strict trust boundary and no-downgrade behavior. First, artifact-contained `.doco-cd.yml` is treated as untrusted for OCI trust-policy override decisions. Second, if global `OCI_TRUST_POLICY.enabled` is `true`, per-deployment `oci.verify: false` cannot disable verification. Some workarounds are available. Do not source deployment config from untrusted OCI artifact contents. Use trusted inline `POLL_CONFIG.deployments` and avoid relying on artifact-contained trust-policy overrides. Restrict write/push permissions for OCI repositories/tags used by doco-cd. Prefer immutable digest pinning and protected release/tag workflows. Monitor for unexpected artifact digest changes and failed/suspicious verification events.

misp · Misp-project misp

A persistent unsafe URL injection vulnerability exists in the MISP dashboard ButtonWidget configuration. Dashboard widget URLs were validated only when the widget was rendered and were not validated when the configuration was saved. As a result, an authenticated user able to modify dashboard widget settings could persist arbitrary URL values, including URLs using the javascript: scheme, through either of the dashboard settings persistence paths. A malicious javascript: URL stored in a dashboard button could potentially result in client-side script execution in the MISP security context if the value reached a rendering or navigation path without the existing runtime validation. Such execution could allow an attacker to perform actions with the privileges of the affected user or access information available to their MISP session. The practical exploitability of this issue is reduced by the fact that MISP already applied URL validation at render time, which neutralized known malicious values before they were presented to the user. The vulnerability therefore represents a persistence-layer validation gap and a defense-in-depth weakness rather than evidence of a direct bypass of the existing rendering protection. The patch introduces a canonical url schema type and validates dashboard widget configuration before it is persisted through either settings save mechanism. ButtonWidget URLs must now be strings resolving to an absolute path on the current MISP instance or a full URL with the same origin. Values using javascript:, external origins, malformed URL forms, and non-string values are rejected at save time.

ash-project ash_oban

Improperly Controlled Modification of Dynamically-Determined Object Attributes vulnerability in ash-project ash_oban allows a user whose input reaches the :args option of AshOban.build_trigger/3 to retarget an update or destroy trigger at another record, including across tenants. build_trigger/3 builds the trusted job arguments with atom keys (:primary_key, :tenant, :action_arguments) and merges the caller's :args underneath so the trusted values win on collision. Because Oban job arguments round-trip through JSON, the caller's keys arrive as strings, so Map.merge sees no collision and both keys survive. When the job is persisted the JSON object is de-duplicated keeping the last (string) key, and the worker reads the caller's value. The documentation describes :args as unable to affect the action, so an application that forwards user input into it for uniqueness scoping is exposed to authorization bypass and tenant isolation breaks. This issue affects ash_oban: from 0.2.5 before 0.8.14.

graphql-go project graphql-go

github.com/graphql-go/graphql (GraphQL for Go) through 0.8.1 does not validate that a scalar variable value matches its declared type. The built-in coerceString and coerceBool functions (scalars.go) accept input whose type does not match the declared String, ID, or Boolean scalar instead of raising the request error that the GraphQL specification mandates. In some cases (but not any typical case of JSON sent to a website), a deeply nested value leads to an unrecoverable "fatal error: stack overflow" condition.

zephyrproject zephyr

The OCPP 1.6 client in subsys/net/lib/ocpp/ocpp.c reconstructs a session handle and PDU id from the uid field of a CALLRESULT message. In ocpp_process_server_msg() the code calls atoi(strtok_r(uid, "-", &tmp)) without checking the strtok_r return value. When the server-supplied uid is empty or contains no - delimiter, strtok_r() returns NULL and atoi(NULL) dereferences a NULL pointer, which is undefined behaviour. The uid originates from network data: parse_rpc_msg() in subsys/net/lib/ocpp/ocpp_j.c JSON-parses a frame received from the OCPP central system over TCP/WebSocket and copies the server-controlled string into the local buffer. A malicious or compromised central system, or a man-in-the-middle on a non-TLS ws:// connection, can return a malformed uid to reach the defect. No authentication beyond the existing server connection (or MITM position) is required, and the reconstructed pointer is membership-validated by ocpp_session_is_valid(), so the impact is limited to the NULL dereference rather than arbitrary pointer use. On Zephyr targets that trap access to address 0 (MMU/MPU platforms or CONFIG_NULL_POINTER_EXCEPTION_DETECTION), the dereference faults inside the OCPP reader thread and invokes the fatal handler, producing a remote denial of service of the charge point; on bare targets where address 0 is readable the call returns 0 and is benign, so the impact is availability-only and platform-conditional. The applied fix guards only the first atoi(); the second strtok_r(NULL, "-", &tmp) followed by pdu = atoi(buf) in the same function remains unguarded and the identical NULL dereference is still reachable from the same network input when the uid has a first token but no second --delimited token. A complete fix should validate the second token as well.

zephyrproject zephyr

The virtio PCI driver (drivers/virtio/virtio_pci.c) parses a device's PCI capability list during driver initialization. In virtio_pci_read_cap() the device-supplied capability length byte cap_len (read from PCI config space via pcie_conf_read()) was only checked with assert(tmp.cap_len == cap_struct_size). That assert resolves to __ASSERT_NO_MSG(), gated by CONFIG_ASSERT, which defaults off in production builds, so the value reached the copy logic completely unvalidated. The length then drives a loop that copies extra capability dwords into a fixed-size stack buffer supplied by the caller. A cap_len below the 24-byte base struct virtio_pci_cap underflows the unsigned extra_data_words count to a near-SIZE_MAX value, producing an effectively unbounded stack write; a cap_len above the caller's buffer (up to 255) writes up to roughly 228 bytes of device-controlled data past the buffer. Both are out-of-bounds writes of attacker-controlled content executed in kernel mode during boot-time device probe. The input originates from the virtio device. In the common deployment where Zephyr runs as a guest under a hypervisor, the device backend is the host, which already fully outranks the guest, so the bug yields no privilege escalation. The exploitable case is a virtio device that is untrusted relative to the Zephyr kernel — an untrusted or physical/passthrough virtio PCIe device on a bare-metal system, or a confidential-computing posture where the guest must defend against the host — where a malicious device can corrupt the kernel stack and potentially achieve code execution or a crash. The fix replaces the compiled-out assert with a runtime range check rejecting cap_len outside [sizeof(struct virtio_pci_cap), cap_struct_size] before any arithmetic or copy.

zephyrproject zephyr

The Zephyr kernel validates the k_thread_join() and k_thread_abort() system calls (declared __syscall in include/zephyr/kernel.h) through thread_obj_validate() in kernel/thread.c. Its default switch branch is the access-denied path, taken when k_object_validate() returns -EPERM (the calling user thread was never granted access to the target thread object) or -EBADF (the supplied pointer is not a registered kernel object of the right type). That branch invoked K_OOPS(K_SYSCALL_VERIFY_MSG(ret, "access denied")), but K_SYSCALL_VERIFY_MSG treats a true expression as success; the non-zero error code ret therefore read as "verified OK", the kernel oops was never raised, and control fell through to CODE_UNREACHABLE. Because k_thread_join() and k_thread_abort() are system calls, an unprivileged user-mode thread (under CONFIG_USERSPACE) can reach this denial path directly by calling either syscall on a thread object it does not own. Instead of the offending thread being cleanly terminated, execution reaches __builtin_unreachable() while running in supervisor mode inside the syscall handler. On Clang builds CODE_UNREACHABLE emits an illegal-instruction trap, so a user thread can deterministically crash the kernel — a locally triggerable denial of service that escapes the userspace sandbox. On GCC builds the path is undefined behavior: the compiler may drop the return-value handling for thread_obj_validate(), so it can return an undefined bool; if that is false, the caller proceeds into the real k_thread_join()/k_thread_abort() implementation for a thread the user was never authorized to access, an access-control bypass. The fix changes the verification expression to ret == 0, so a denied (non-zero) result now correctly raises K_OOPS and terminates the offending caller.

nxp-auto-goldvip gvip

A security vulnerability has been detected in nxp-auto-goldvip gvip up to 1.4.0. Affected by this issue is the function SitewiseCustomFunction of the component Lambda Function Handler. Such manipulation leads to improper access controls. The attack can be launched remotely. Upgrading to version 1.15.0 can resolve this issue. Upgrading the affected component is advised. The project explains: "The reported IAM permission configuration is a known historical issue that was already addressed in 2024, beginning with GoldVIP version 1.13.0. The permissions were updated in subsequent releases, including version 1.15.0. In addition, we also sent a request to either update or deprecate the older release in the AWS SAR application repository."

pdm-project pdm

pdm is a Python package and dependency manager supporting the latest PEP standards. In versions prior to 2.27.0, pdm writes several project-local state or configuration files without symlink protection. If a malicious repository places those files as symlinks, local PDM operations can overwrite the symlink targets. This creates an arbitrary file clobber primitive relative to the privileges of the invoking user. Config.__init__() resolves the project-local pdm.toml path and _save_config() writes to the resolved target. If PROJECT_ROOT/pdm.toml is a symlink to another file, pdm config -l ... updates the target file instead of refusing the write. The same general problem exists for other project-local persistence paths that are written directly with no lstat / O_NOFOLLOW protection. For the pdm.toml PoC specifically, the target file must already contain parseable TOML. Otherwise the load step fails before the write path is reached. That parser constraint does not apply to the .pdm-python or .python-version sinks. This issue has been fixed in version 2.27.0.

Oracle Corporation Oracle Project Manufacturing · Oracle project manufacturing

Vulnerability in the Oracle Project Manufacturing product of Oracle E-Business Suite (component: PJM Command Center). The supported version that is affected is V16. Difficult to exploit vulnerability allows high privileged attacker with logon to the infrastructure where Oracle Project Manufacturing executes to compromise Oracle Project Manufacturing. Successful attacks of this vulnerability can result in unauthorized access to critical data or complete access to all Oracle Project Manufacturing accessible data as well as unauthorized update, insert or delete access to some of Oracle Project Manufacturing accessible data. CVSS 3.1 Base Score 4.7 (Confidentiality and Integrity impacts). CVSS Vector: (CVSS:3.1/AV:L/AC:H/PR:H/UI:N/S:U/C:H/I:L/A:N).

zephyrproject zephyr

The NXP LPUART serial driver (drivers/serial/uart_mcux_lpuart.c), when CONFIG_UART_USE_RUNTIME_CONFIGURE is enabled, called LPUART_Deinit() at the start of mcux_lpuart_configure(), which disables the LPUART peripheral clocks. The requested configuration is validated only afterwards (in mcux_lpuart_configure_basic), and unsupported parity/data-bit/stop-bit/flow-control values return -ENOTSUP before the clock is re-enabled. As a result, a uart_configure() request with an unsupported configuration left the LPUART in a clock-disabled state; any subsequent access to LPUART registers (poll_out/poll_in, interrupt handling, or a later reconfigure) faults on the gated peripheral and escalates to a hard fault, crashing the system. uart_configure() is a Zephyr syscall whose verifier (z_vrfy_uart_configure) only checks that cfg is readable user memory and forwards the caller-supplied configuration unchanged, so an unprivileged userspace thread with access to an LPUART device can deterministically trigger the fault, a persistent system-wide denial of service. Introduced in v2.5.0 and present in all subsequent releases until this fix, which removes the LPUART_Deinit() call and instead only disables the transmitter/receiver, leaving the clock running.

ci4-cms-erp ci4ms

CI4MS is a CodeIgniter 4-based content management system skeleton. Prior to version 0.31.9.0, the Fileeditor module enforces an extension allowlist (`['css','js','html','txt','json','sql','md']`) on content-write operations (`saveFile`, `createFile`), but two destructive endpoints — `deleteFileOrFolder` and `renameFile` — never validate the extension of the *source* path. A backend user with file-editor permissions can therefore unlink or rename any file inside the project root that is not explicitly listed in the small `$hiddenItems` blocklist. Critical framework files such as `app/Config/Routes.php`, `app/Config/App.php`, `app/Config/Database.php`, `app/Config/Filters.php`, `public/index.php`, and `public/.htaccess` all live outside that blocklist and can be destroyed, producing a persistent denial of service that requires filesystem-level redeployment to recover. Version 0.31.9.0 patches the issue.

MervinPraison PraisonAI

PraisonAI (pip package praisonaiagents) before 1.6.78 automatically loads defaults from a project-local .praisonai/config.toml when constructing an Agent, and does not validate the defaults.output.output_file path. A repository-controlled config file can set output_file to an absolute or '..' traversal path; when the developer subsequently calls agent.start() without explicitly passing an output parameter, PraisonAI writes the agent response to that path (creating parent directories as needed), allowing an untrusted checked-out project to overwrite files outside the project root with the privileges of the user running PraisonAI.

ash-project ash

Improperly Controlled Modification of Dynamically-Determined Object Attributes vulnerability in ash-project ash allows a user to set the value of a private action argument that is intended to be controlled only by trusted server-side code. Action arguments declared with public?: false are meant to be set internally (for example via Ash.Changeset.set_private_argument/3) and must not be settable from end-user input. When a changeset is built from a parameter map, Ash filters out private arguments, but the filtering is incomplete. In the regular changeset path (for_create, for_update, for_destroy), private arguments are stripped only when the parameter key is an atom. When the key is a binary (string), as is the case for user-supplied parameters, the private argument is kept and the user controls its value. In the atomic path (Ash.Changeset.fully_atomic_changeset/4, also reached through atomic and bulk updates), private arguments are not stripped at all, regardless of whether the key is an atom or a binary. An attacker who can submit parameters to an action that defines a private argument can therefore inject a value for that argument. Depending on how the application uses the argument (for example an acting_user_id driving authorization or record ownership), this can lead to an integrity violation or privilege escalation. This issue affects ash: from 3.0.0 before 3.29.3.

zephyrproject zephyr

bt_sdp_parse_attribute() in subsys/bluetooth/host/classic/sdp.c validated only that the SDP record buffer held the type-marker byte plus the 2-byte attribute ID (a check of buf->len < 3) but then read a fourth byte, the data-element descriptor (type), via net_buf_simple_pull_u8(). Because net_buf_simple_pull_u8() dereferences buf->data[0] before its only bounds guard (an __ASSERT_NO_MSG that compiles out when CONFIG_ASSERT is disabled, the production default), a record of exactly three bytes (0x09 followed by a 2-byte attribute ID) causes a one-byte read past the end of the logical buffer. The parser is reachable from inbound, remote-controlled data: a Bluetooth BR/EDR peer acting as an SDP server returns discovery-response records that are stored verbatim in the client receive buffer and parsed via the public bt_sdp_get_attr()/bt_sdp_has_attr()/bt_sdp_record_parse() helpers. The over-read is bounded to a single byte that is used only as an internal length selector and is never leaked to the attacker; subsequent length checks then reject the malformed record. Realistic impact is therefore limited to an edge-case denial of service (a fault only if the record ends exactly at a mapped-memory boundary, or a deterministic assert panic when CONFIG_ASSERT=y). Affects Zephyr v4.3.0 and v4.4.0; fixed by adding sizeof(type) to the length check.

Red Hat Enterprise Linux 8 · Red Hat Enterprise Linux 8.4 Advanced Mission Critical Update Support · Red Hat Enterprise Linux 8.4 Extended Update Support Long-Life Add-On · Red Hat Enterprise Linux 8.6 Advanced Mission Critical Update Support

A content injection vulnerability was found in the ABRT post-create event handler scripts in libreport. The event script queries the systemd journal for log entries matching the crashed process and writes the results to files in the dump directory without sanitizing embedded control characters. A local user can inject arbitrary content into the journal output by embedding newline characters in syslog messages, controlling the content that root writes to dump directory files.

LearningCircuit local-deep-research

Local Deep Research is an AI-powered research assistant for deep, iterative research. Prior to 1.6.10, the URL checking logic in local-deep-research has a logical flaw that could be bypassed by attackers, leading to SSRF attacks. The current project uses validate_url to validate the input URL. The main logic is to perform security checks on the host portion of the URL extracted by urlparse to prevent SSRF attacks. However, there are indeed differences in parsing between urlparse and the library that actually sends the request. For example, in safe_get, validate_url is first used to perform an SSRF check, and then requests.get is used to send the actual request. This vulnerability is fixed in 1.6.10.

zephyrproject-rtos Zephyr · Zephyrproject zephyr

A bitwise shift vulnerability in Zephyr's PTP subsystem allows a remote attacker to cause undefined behavior and potential system crashes. An attacker sends a crafted PTP_MSG_MANAGEMENT message to set an unvalidated negative log_announce_interval value in the port's data set. When a subsequent PTP_MSG_ANNOUNCE message is processed, port_timer_set_timeout_random computes a timeout as NSEC_PER_SEC >> -log_seconds; if the attacker-supplied value is sufficiently negative (e.g., -127), the shift amount exceeds the 64-bit integer width, triggering undefined behavior in C. This can cause a system crash via a compiler-generated illegal instruction trap on some architectures, or produce an erroneous zero timeout leading to resource starvation loops or other logical errors.