Recherche « IBM Controller »

IBM Guardium Data Protection

IBM Guardium Data Protection 12.2.2 is affected by a denial-of-service vulnerability in the edge-controller. An unauthenticated remote attacker with network access to the edge-controller gRPC service can provide malformed task data that triggers an unchecked type assertion, causing the edge-controller process to terminate unexpectedly.

IBM WebSphere Application Server - Liberty · Ibm websphere application server

IBM WebSphere Application Server - Liberty 17.0.0.3 through 26.0.0.8 is vulnerable to cross-site request forgery which could allow an attacker to perform SSRF attacks with elevated privileges when the collectiveController-1.0 feature is enabled.

IBM WebSphere Application Server - Liberty · Ibm websphere application server

IBM WebSphere Application Server - Liberty 17.0.0.3 through 26.0.0.8 ND Collective Controller is affected by a path-segment injection vulnerability in the collective routing mechanism.

zephyrproject zephyr

The MCTP-over-I2C+GPIO target binding in Zephyr (subsys/pmci/mctp/mctp_i2c_gpio_target.c) processes pseudo-register writes from an I2C bus master byte-by-byte in mctp_i2c_gpio_target_write_received() without validating the order or the receive buffer. In the affected versions the MCTP_I2C_GPIO_RX_MSG_ADDR (data) handler dereferences and writes through b->rx_pkt without checking that the receive buffer was allocated: a controller that selects the data register and writes a byte without first sending the length register (which is what allocates the buffer) causes a write of an attacker-chosen byte through a NULL/unallocated mctp_pktbuf pointer (i.e. into a small attacker-advanceable offset above address 0), producing memory corruption or a hard fault. The same handler also performs a write-then-check bounds test, allowing a one-byte heap overflow at data[255] when more than 255 data bytes are sent. Because the I2C target callback is invoked with raw bytes supplied by whatever device is the bus master and the binding performs no authentication, a malicious or malfunctioning controller on the bus can trigger these without any prior protocol state, leading to memory corruption and/or denial of service on the target device. The vulnerable code was introduced when the I2C+GPIO target binding was added and shipped in Zephyr v4.3.0 and v4.4.0. The fix defers allocation to the first data byte with a NULL check, treats a missing length as a zero-sized packet rejected by libmctp, and moves the bounds check before the store.

IBM Controller

IBM Controller 11.0.1, 11.1.0, 11.1.1, and 11.1.2 contains hard-coded credentials, such as a password or cryptographic key, which it uses for its own inbound authentication, outbound communication to external components, or encryption of internal data.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ibmasm: fix heap over-read in ibmasm_send_i2o_message() The ibmasm_send_i2o_message() function uses get_dot_command_size() to compute the byte count for memcpy_toio(), but this value is derived from user-controlled fields in the dot_command_header (command_size: u8, data_size: u16) and is never validated against the actual allocation size. A root user can write a small buffer with inflated header fields, causing memcpy_toio() to read up to ~65 KB past the end of the allocation into adjacent kernel heap, which is then forwarded to the service processor over MMIO. Silently clamping the copy size is not sufficient: if the header fields claim a larger size than the buffer, the SP receives a dot command whose own header is inconsistent with the I2O message length, which can cause the SP to desynchronize. Reject such commands outright by returning failure. Validate command_size before calling get_mfa_inbound() to avoid leaking an I2O message frame: reading INBOUND_QUEUE_PORT dequeues a hardware frame from the controller's free pool, and returning without a corresponding set_mfa_inbound() call would permanently exhaust it. Additionally, clamp command_size to I2O_COMMAND_SIZE before the memcpy_toio() so the MMIO write stays within the I2O message frame, consistent with the clamping already performed by outgoing_message_size() for the header field.