Samedi 22 août 2026

Linux

In the Linux kernel, the following vulnerability has been resolved: NFS: Pin the 'struct nfs_server' during a FREE_STATEID call Dan Aloni reports that he was able to hit a use-after-free bug if a FREE_STATEID operation gets delayed for whatever reason. Fix this by bumping the refcount of the 'struct nfs_server' object for the duration of the FREE_STATEID so it doesn't get cleaned up from underneath us while operations are still in flight.

Linux

In the Linux kernel, the following vulnerability has been resolved: ovpn: skip rehash for peers already removed from by_id ovpn_nl_peer_set_doit() resolves the target peer via ovpn_peer_get_by_id() before taking ovpn->lock. In the window between the lookup (which only takes a refcount) and the subsequent spin_lock_bh(&ovpn->lock), a concurrent OVPN_CMD_PEER_DEL, keepalive expiry, or socket teardown can take ovpn->lock first, run ovpn_peer_remove() to unhash the peer from all four tables (by_id, by_vpn_addr4/6, by_transp_addr) and release the lock. set_doit then acquires ovpn->lock and calls ovpn_peer_hash_vpn_ip(), which re-inserts the now-removed peer back into the rehashing tables. The same race affects the float path: ovpn_peer_endpoints_update() holds only a refcount and acquires ovpn->lock very late (after async AEAD decrypt and a netlink notification), then rehashes the peer in the by_transp_addr table. The resurrected peer becomes reachable again from the RX lookup (ovpn_peer_get_by_transp_addr) and the TX VPN-IP lookup, even though userspace believes it is gone. Once the data-path refcount drops the peer is freed via call_rcu while the hash entries embedded in it remain linked, opening a UAF window. Bail out of the rehash when hash_entry_id is unhashed, mirroring the sentinel already used by ovpn_peer_remove() to detect the already-removed state. The check is safe under ovpn->lock, which serializes every mutation of hash_entry_id, and is a no-op for the add path because ovpn_peer_add_mp() inserts hash_entry_id before calling ovpn_peer_hash_vpn_ip().

Linux

In the Linux kernel, the following vulnerability has been resolved: btrfs: lzo: reject inline extents without valid headers [BUG] For a crafted btrfs image, the following KASAN can be triggered when reading an inline lzo compressed file extent: BUG: KASAN: slab-out-of-bounds in lzo_decompress+0x57d/0x700 Read of size 4 at addr ffff888006f2e644 by task btrfs_lzo_inlin/77 Call Trace: <TASK> dump_stack_lvl+0x5b/0x70 print_report+0xd1/0x610 kasan_report+0xe0/0x110 __asan_report_load_n_noabort+0x13/0x20 lzo_decompress+0x57d/0x700 btrfs_decompress+0x140/0x1c0 uncompress_inline+0x147/0x1b0 btrfs_get_extent+0xb23/0x10a0 btrfs_do_readpage.constprop.0+0x538/0x1ac0 btrfs_readahead+0x32f/0x5f0 read_pages+0x16f/0x850 page_cache_ra_unbounded+0x296/0x490 do_page_cache_ra+0xd9/0x130 page_cache_sync_ra+0x3ee/0x6f0 filemap_get_pages+0x306/0x15c0 filemap_read+0x329/0xd00 btrfs_file_read_iter+0x1f8/0x2b0 vfs_read+0x4ef/0x720 ksys_read+0xf8/0x1d0 __x64_sys_read+0x71/0xb0 x64_sys_call+0x1ab0/0x1b70 do_syscall_64+0x61/0x470 entry_SYSCALL_64_after_hwframe+0x4b/0x53 </TASK> [CAUSE] For an inline lzo compressed file extent, there should always be one lzo header, recording the total length of the compressed data, followed by one segment header, recording the compressed lzo payload. But if a crafted inline lzo compressed file extent contains only an lzo header, without the segment header or payload, lzo_decompress() will still try to read the segment header, causing a read beyond the item boundary. Furthermore if the inline lzo compressed file extent is the first item of the leaf, it will be at the extent buffer boundary. The above out-of-boundary read will go beyond the extent buffer boundary, triggering the above KASAN report. [FIX] Validate the total length of the inlined lzo compressed file extent, to make sure there is at least one LZO header and one segment header, and a non-zero payload. [ Rework the commit message to remove slop ]

Linux

In the Linux kernel, the following vulnerability has been resolved: vdpa/mlx5: Fix buffer length in create_direct_keys() We have seen in our CI the following KASAN message: BUG: KASAN: slab-out-of-bounds in cmd_exec+0x550/0xca0 [mlx5_core] Read of size 272 at addr 0000000176795020 by task qemu-system-s39/82764 [...] [<000011388ab3a7a0>] cmd_exec+0x550/0xca0 [mlx5_core] [<000011388ab3b61c>] mlx5_cmd_exec_cb+0x25c/0x4f0 [mlx5_core] [<000011388b21e82e>] mlx5_vdpa_exec_async_cmds+0x22e/0x5e0 [mlx5_vdpa] [<000011388b21fd44>] create_direct_keys+0x954/0xef0 [mlx5_vdpa] [...] The buggy address is located 4128 bytes inside of allocated 4384-byte region [0000000176794000, 0000000176795120) So in essence we read 16 bytes beyond 4384-byte allocation. create_direct_keys calculates the pointer and length for in and out buffers. The size calculation for in includes the entire structure size (out + in + mtt[]) but the pointer passed to cmd_exec points only to the 'in' field, skipping the 'out' field. This causes mlx5_copy_to_msg() to read beyond the allocated buffer by sizeof(out) bytes when copying command data. Properly calculate the input size to match the pointer and allocation size.

Linux

In the Linux kernel, the following vulnerability has been resolved: udp: fix potential use-after-free in tunnel segmentation __skb_udp_tunnel_segment() gets the UDP header before ensuring the tunnel header is in the skb head. If the pull reallocates skb->head, the saved UDP header pointer is no longer valid. Get the UDP header after the pull to avoid a potential use-after-free.

Linux

In the Linux kernel, the following vulnerability has been resolved: sctp: clear control chunk transport if it is being removed sctp_make_heartbeat_ack() caches the destination transport in chunk->transport without taking a reference. When src_out_of_asoc_ok is enabled, the HEARTBEAT ACK may remain queued on control_chunk_list instead of being transmitted immediately. If the peer transport is removed while the chunk is still queued, sctp_assoc_rm_peer() drops the transport and schedules it for RCU freeing, but only clears cached transport pointers in out_chunk_list. The queued control chunk therefore retains a dangling transport pointer. Once an ASCONF_ACK clears the suppression and the queued control chunk is transmitted, SCTP dereferences the stale transport pointer, leading to a use-after-free. Fix this by also clearing chunk->transport for queued control chunks in control_chunk_list when removing the transport.

Linux

In the Linux kernel, the following vulnerability has been resolved: ipvs: clear IPv4 options after rebasing tunnel ICMP errors ip_vs_in_icmp() rebases an skb from the outer ICMP packet to the quoted original request before passing it to icmp_send(). However, IPCB(skb)->opt still describes the outer IPv4 header. A timestamp option in the outer header can therefore leave an offset that points into the quoted transport header after the rebase. __ip_options_echo() treats a byte at that stale location as the option length and copies it into the fixed-size option storage on the __icmp_send() stack, causing a stack out-of-bounds write. Clear the stale option metadata after resetting the network header. Keep the remaining control block fields, including the ingress interface used by the ICMP response path.

Linux

In the Linux kernel, the following vulnerability has been resolved: net: fix skb length accounting after generic XDP frag adjustment Generic XDP exposes non-linear skb fragments through an xdp_buff. If an XDP program adjusts the fragment area, bpf_prog_run_generic_xdp() copies xdp_frags_size back to skb->data_len but leaves skb->len containing the old fragment contribution. After a fragment shrink, this makes skb_headlen() larger than the actual linear area. In the reproduced UDP receive path, __skb_datagram_iter() copied 1024 bytes past the actual linear tail to userspace, starting at struct skb_shared_info. The copied bytes included the affected skb's nr_frags, xdp_frags_size and a kernel pointer from skb_shinfo(skb)->frags[0]. Real packet data was displaced by the same amount and truncated at the end. Subtract the old data_len before replacing it and add the new data_len afterwards, keeping skb->len and skb->data_len synchronized. A 60000-byte UDP datagram on a veth pair with MTU 64000 was shortened by 1024 bytes from its fragment area. Before the fix, all 10 runs produced corrupted payloads. After the fix, all 10 runs matched the expected payload exactly.

Linux

In the Linux kernel, the following vulnerability has been resolved: inet: frags: publish queues before arming timer inet_frag_create() arms the fragment queue timer before inserting the queue into the fqdir rhashtable. If the namespace fragment timeout is zero or negative, the timer can run before the queue is published. The timer callback then marks the queue complete, tries to remove a node that is not in the hash table yet, and drops the anticipated hash reference. Creation can subsequently publish the completed queue without restoring that reference, leaving a stale hash node after the caller drops the remaining reference. Publish the queue first and arm the timer while holding the queue lock. This makes timer expiry wait until the queue is visible in the hash table, so inet_frag_kill() can remove the node and balance the hash reference.

Linux

In the Linux kernel, the following vulnerability has been resolved: net/x25: fix use-after-free of the socket by its timers The x25 timers are armed with mod_timer() and cancelled with timer_delete(), so a pending timer holds no reference on the socket and a cancel does not wait for a callback already running on another CPU. x25_heartbeat_expiry() also rearms unconditionally, so it can reinstall sk->sk_timer after __x25_destroy_socket() has passed its cancel point. The following __sock_put() frees the socket while the timer is still queued, and the next expiry uses freed memory. KASAN reports a slab-use-after-free on the kmalloc-2k object freed by close(). timer_delete_sync() cannot be used here: x25_heartbeat_expiry() and x25_timer_expiry() both reach the cancels from inside the timer they would wait on, through __x25_destroy_socket() and x25_disconnect(). Arm the timers with sk_reset_timer() and cancel them with sk_stop_timer() so that an armed timer owns a reference, and release it in both expiry handlers. Rearm the heartbeat only while sk_hashed(sk) is still true, since __x25_destroy_socket() unlinks the socket before dropping it. Arm the deferred destroy timer the same way and drop its reference in x25_destroy_timer(). Reproduced on net with KASAN, with the heartbeat period shortened so the window recurs. With this patch the reproducer no longer triggers a report and /proc/net/x25 drains. Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>

Linux

In the Linux kernel, the following vulnerability has been resolved: dibs: initialise dibs->lock in dibs_dev_alloc() dibs->lock is initialised by dibs_dev_add(), but a dibs device can already take interrupts before that call: ism_probe() runs ism_dev_init(), and hence request_irq(), before it calls dibs_dev_add(). No client can have registered a dmb at that point, so no dmb interrupt can occur, but a GID event interrupt can, and ism_handle_irq() takes dibs->lock unconditionally on entry, before it inspects anything else. Initialise the lock in dibs_dev_alloc() instead, so that it is valid as soon as a driver can publish the device to its interrupt handler.

Linux

In the Linux kernel, the following vulnerability has been resolved: xdp: reject clones that overrun skb_shared_info tailroom xdpf_clone() clones broadcast copies into a single page and sets frame_sz to PAGE_SIZE. __xdp_build_skb_from_frame() later treats that page like a normal XDP frame and expects the usual skb_shared_info tailroom at the end of the buffer. The current check only rejects frames whose linear xdp_frame header, headroom, and packet data exceed PAGE_SIZE. A source frame backed by a larger allocation can still satisfy that check while extending into the clone's required shared-info area. When such a clone is converted back into an skb, build_skb_around() places skb_shared_info over live packet bytes and later writes can corrupt XDP return metadata. Reject clones unless their linear area fits inside SKB_WITH_OVERHEAD(PAGE_SIZE), matching the tailroom requirement already enforced by the XDP-to-skb conversion path.

Linux

In the Linux kernel, the following vulnerability has been resolved: veth: fix skb length accounting after XDP frag adjustment veth exposes non-linear skb fragments through an xdp_buff. If an XDP program adjusts the fragment area, veth_xdp_rcv_skb() copies xdp_frags_size back to skb->data_len but leaves skb->len containing the old fragment contribution. After a fragment shrink, this makes skb_headlen() larger than the actual linear area. In the reproduced UDP receive path, __skb_datagram_iter() copied 1024 bytes past the actual linear tail to userspace, starting at struct skb_shared_info. The copied bytes included the affected skb's nr_frags, xdp_frags_size, and a kernel pointer from skb_shinfo(skb)->frags[0]. Real packet data was displaced by the same amount and truncated at the end. Subtract the old data_len before replacing it and add the new data_len afterwards, keeping skb->len and skb->data_len synchronized. Additionally, bpf_xdp_pull_data() can advance data_end while leaving frags present. The skb is then still non-linear, so the old __skb_put(skb, off) triggers SKB_LINEAR_ASSERT(). Use skb_set_tail_pointer() and update skb->len explicitly instead, following bpf_prog_run_generic_xdp(). Unlike __skb_put(), skb_set_tail_pointer() does not require a linear skb. A 60000-byte UDP datagram on a veth pair with MTU 64000 was shortened by 1024 bytes from its fragment area. Before the fix, all 10 runs produced corrupted payloads. After the fix, all 10 runs matched the expected payload exactly. A forced-tailroom reproducer also exercises bpf_xdp_pull_data() with frags still present; the old code triggers SKB_LINEAR_ASSERT(), while this fix passes 10/10 runs.

Linux

In the Linux kernel, the following vulnerability has been resolved: tls: rx: restore msg_iter before TLS 1.3 optimistic retry tls_decrypt_sg() advances msg->msg_iter when it maps user pages for the optimistic TLS 1.3 zero-copy path. If the decrypted record turns out not to be unpadded application data, tls_decrypt_sw() retries into a kernel skb, but leaves the iterator advanced. The subsequent copy from the skb then writes decrypted bytes again at a later point in the caller iovecs while recvmsg() reports only the post-retry length. A TLS peer can trigger this after the receiver enables TLS_RX_EXPECT_NO_PAD. Revert the iterator by the number of bytes consumed by the optimistic mapping before retrying without zero-copy. Add a selftest which sends a TLS 1.3 control record with TLS_RX_EXPECT_NO_PAD enabled and verifies that recvmsg() does not overwrite later iovecs beyond the returned length.

Linux

In the Linux kernel, the following vulnerability has been resolved: smb: client: Fix use-after-free in cifs_try_adding_channels() cifs_try_adding_channels() takes a temporary reference to an interface before dropping iface_lock. If cifs_ses_add_channel() fails, it drops that reference and then increments iface->weight_fulfilled. A concurrent interface list refresh can remove the list reference while channel creation is in progress. In that case, the failure-path kref_put() releases the last reference and frees iface. Updating weight_fulfilled afterward then accesses freed memory. Increment weight_fulfilled before dropping the temporary reference, keeping iface alive for the final access.

Linux

In the Linux kernel, the following vulnerability has been resolved: ip6_tunnel: clear skb2->cb[] in ip6ip6_err() ip6ip6_err() clones an outer IPv6 ICMP error skb, pulls it to the quoted inner IPv6 packet, and then passes the clone to icmpv6_send(). The clone still carries the outer packet's inet6_skb_parm in skb->cb. If the outer packet had a Home Address Option, IP6CB(skb2)->dsthao remains non-zero after skb_pull(). icmpv6_send() later calls mip6_addr_swap(), which uses that stale dsthao offset against the quoted inner packet. A malformed inner destination-options header can then make the HAO lookup and address swap run past the end of the quoted packet and corrupt skb_shared_info. Clear skb2->cb[] before pulling the quoted inner IPv6 packet so the reply path does not reuse metadata left by the outer IPv6 stack.

Linux

In the Linux kernel, the following vulnerability has been resolved: mm/filemap: __filemap_add_folio() restore index before retrying In __filemap_add_folio()'s split-a-conflict loop, xas_set_order() is applied repeatedly: each application modifies xas.xa_index, rounding it down according to the split_order attempted at that stage: and if all goes as intended, it eventually (or immediately) converges on an xas_try_split() to the required folio_order, with xas.xa_index now the same as index: then xas_store() puts the new folio into the xarray there. But if a new node was needed, and GFP_NOWAIT allocation did not get one, the lock is dropped, xas_nomem() used to allocate, and sequence retried. If (that part of) the xarray is unchanged when the lock is reacquired, no problem. But what if the conflict was meanwhile resolved by another thread (perhaps even doing the same thing, inserting a folio at that same index)? Isn't there a danger of now putting our folio into the xarray at an intermediate rounded-down index? With !folio_contains() bug to follow, when CONFIG_DEBUG_VM=y is checking for that. Fix this with an xas_set_order() to restore the original xas.xa_index at the bottom of the loop, so the retry does a full re-evaluation after reacquiring the lock, and cannot reach xas_store() with the wrong index. Production was suffering from rare SIGILLs and SIGSEGVs, executable text found a page away from where it belonged, !folio_contains() bug hit when debug enabled: symptoms not seen since this patch went in.

Linux

In the Linux kernel, the following vulnerability has been resolved: sctp: keep chunk->transport in step with the list it is queued on __sctp_outq_flush_rtx() moves a gap-acked chunk onto another transport's transmitted list without updating chunk->transport: if (chunk->tsn_gap_acked) { list_move_tail(&chunk->transmitted_list, &transport->transmitted); continue; } The chunk then sits on a live transport's list while chunk->transport still names a different one. If that transport is removed - sctp_assoc_rm_peer() from an ASCONF Delete-IP - sctp_transport_free() RCU-frees it and the chunk is left with a dangling pointer. sctp_assoc_rm_peer() scrubs peer->transmitted and asoc->outqueue.out_chunk_list, but the chunk is on neither. The pointer is not followed while tsn_gap_acked is set. A SACK that reneges on the TSN clears the flag, and the next SACK reaches tchunk->transport->flight_size -= sctp_data_size(tchunk); inside the freed transport. KASAN reports a slab-use-after-free read in sctp_check_transmitted(), freed from sctp_assoc_rm_peer(). Both the removal and the SACKs come from the association peer. Set chunk->transport at the move. The ordinary resend path needs nothing: it reaches its list_move_tail() only after sctp_packet_append_chunk() returned SCTP_XMIT_OK, and __sctp_packet_append_chunk() has rebound the chunk by then. Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>

Linux

In the Linux kernel, the following vulnerability has been resolved: sctp: fix use-after-free of cached ASCONF chunk addip_last_asconf caches the outstanding outbound ASCONF chunk. The normal ASCONF-ACK completion path releases the chunk and clears the pointer. However, sctp_asconf_queue_teardown() releases the cached chunk without clearing addip_last_asconf. During peer restart handling, sctp_sf_do_dupcook_a() queues SCTP_CMD_PURGE_ASCONF_QUEUE, which invokes sctp_asconf_queue_teardown() while the association remains alive and leaves the pointer dangling. A delayed authenticated ASCONF-ACK can then reach sctp_sf_do_asconf_ack(), which accesses the stale chunk and passes it to sctp_process_asconf_ack(), causing a use-after-free and a second release. Clearing the pointer exposes a race with T4 expiry. Peer restart handling queues the timer stop before the purge, but SCTP_CMD_TIMER_STOP uses timer_delete(), which does not wait for a callback already running on another CPU. Such a callback can reach sctp_sf_t4_timer_expire() after the purge and dereference NULL. Clear addip_last_asconf after releasing the cached chunk, and make sctp_sf_t4_timer_expire() consume a stale T4 expiry if no outstanding ASCONF remains.

Linux

In the Linux kernel, the following vulnerability has been resolved: sctp: clear new_transport when removing a peer sctp_process_asconf_param() stores a newly added peer transport in asoc->new_transport. After all parameters in the ASCONF chunk have been processed, sctp_sf_do_asconf() uses this pointer to send a HEARTBEAT to the new transport. An authenticated ASCONF from a remote SCTP peer can add a transport and remove it again with a wildcard DEL-IP parameter in the same chunk. The wildcard deletion preserves the transport on which the ASCONF arrived, but removes the newly added transport through sctp_assoc_del_nonprimary_peers(). The removal does not clear asoc->new_transport, leaving it pointing to the removed transport. sctp_sf_do_asconf() then creates a HEARTBEAT whose chunk->transport points to the removed transport without holding a transport reference. During local address replacement, src_out_of_asoc_ok keeps this HEARTBEAT on control_chunk_list. After the transport is freed by RCU, a successful ASCONF_ACK for the replacement address releases the queued HEARTBEAT and sctp_outq_select_transport() reads the freed transport's state. The issue was found during a static audit of SCTP objects. With an authenticated peer, the reproducer triggered the same KASAN report in 2 of 2 unpatched runs on a KASAN-enabled netdev/main kernel: BUG: KASAN: slab-use-after-free in sctp_outq_select_transport Read of size 4 at addr ffff88800b9bd95c by task python3/197 Call Trace: sctp_outq_select_transport+0x549/0x8b0 [sctp] sctp_outq_flush+0x306/0x2c60 [sctp] sctp_transport_immediate_rtx+0xaf/0x260 [sctp] sctp_process_asconf_ack+0xa48/0xf70 [sctp] Allocated by task 197: sctp_transport_new+0x68/0x650 [sctp] sctp_assoc_add_peer+0x258/0x12a0 [sctp] sctp_process_asconf+0x5e9/0x1090 [sctp] Last potentially related work creation: __call_rcu_common.constprop.0+0x77/0xb70 sctp_assoc_del_nonprimary_peers+0x7c/0xd0 [sctp] sctp_process_asconf+0xd9c/0x1090 [sctp] The first invalid access was a four-byte read of transport->state at net/sctp/outqueue.c:833. The same reproducer completed the full authenticated ASCONF and local-address replacement sequence with this change without a KASAN report or oops. Clear new_transport when its peer is removed, before it can be used to create the HEARTBEAT.

westguard WS Form LITE – Drag & Drop Contact Form Builder

The WS Form LITE – Drag & Drop Contact Form Builder plugin for WordPress is vulnerable to PHP Object Injection in all versions up to, and including, 1.10.80 via deserialization of untrusted input from form submission meta values. This makes it possible for unauthenticated attackers to inject a PHP Object. No known POP chain is present in the vulnerable software, which means this vulnerability has no impact unless another plugin or theme containing a POP chain is installed on the site. If a POP chain is present via an additional plugin or theme installed on the target system, it may allow the attacker to perform actions like delete arbitrary files, retrieve sensitive data, or execute code depending on the POP chain present.

fabrikar.com Fabrik extension for Joomla

Joomla Extension - fabrikar.com - heredoc terminator breakout in the calc element in Fabrik < 4.7.2 - The onUpdateComment endpoint did not perform any access checks.

fabrikar.com Fabrik extension for Joomla

Joomla Extension - fabrikar.com - Missing ACL check in download element in Fabrik < 4.7.2.

fabrikar.com Fabrik extension for Joomla

Joomla Extension - fabrikar.com - Path Traversal via image element in Fabrik < 4.7.2.

fabrikar.com Fabrik extension for Joomla

Joomla Extension - fabrikar.com - Remote code execution via image element in Fabrik < 4.7.2.

fabrikar.com Fabrik extension for Joomla

Joomla Extension - fabrikar.com - Unauthenticated remote code execution via PHP form element in Fabrik < 4.7.2 - The PHP form element is vulnerable to the execution of user provided codes.

fabrikar.com Fabrik extension for Joomla

Joomla Extension - fabrikar.com - Unauthenticated SQL injection in ORDER BY in Fabrik < 4.7.2 - The order parameter in list models is used in queries without validation, allowing read SQLi vectors.

fabrikar.com Fabrik extension for Joomla

Joomla Extension - fabrikar.com - Unauthenticated SQL injection in list filter condition parameter in Fabrik < 4.7.2 - The condition parameter passed to a list filter is concatenated verbatim into the WHERE clause built by getFilterQuery(). An unauthenticated attacker can supply arbitrary SQL through the filter condition, giving full read of the database.

Punk versions before 0.18 for Perl allow session cookie forgery via an empty default HMAC key when a session is declared without a secret. The session keyword freezes its options onto the application as given: it does not require a secret, warn, or refuse to start when one is absent. The cookie read and the write-back both default that key to the empty string, so a declaration with no secret option, or with an undefined or empty one, signs and verifies with a zero-length HMAC-SHA256 key. An attacker who knows the cookie format can then mint one offline carrying any contents the session holds, such as a user identifier or a role. Nothing marks the misconfiguration at runtime: cookies are well formed and sessions round-trip as expected.

Punk::OAuth2::Server versions through 0.03 for Perl issue access tokens outside a client's registered scopes and grant types because no authorization path reads them. Punk::OAuth2::Server::Store registers scopes and grant_types per client and documents both as client registration. token dispatches on the grant_type in the request body, so a client registered for authorization_code alone can ask for client_credentials, and that arm passes the requested scope straight to the minter, which signs it into the at+jwt access token. authorize copies the query scope into the authorization code record without comparing it against the registration, leaving the optional consent hook as the only check between an arbitrary scope and the issued code. redirect_uris on the same client row is read and enforced. A registered client can obtain a correctly signed token carrying any scope it names, and a resource server running Punk::OAuth2::Checker accepts that token and honours the scope. A client registered without a secret authenticates on its client_id alone, so anyone who knows that identifier can request one.

TRENDnet TEW-821DAP

A vulnerability was determined in TRENDnet TEW-821DAP 2.2.01b05. Affected by this vulnerability is the function uci_safe_get of the file /cgi-bin/apply_time.cgi of the component NTP Timezone Configuration Handler. Executing a manipulation of the argument system.ntp.server/system.ntp.enable_server/cameo.time.time_zone/cameo.cameo.syslog_server can lead to stack-based buffer overflow. The attack may be launched remotely. The exploit has been publicly disclosed and may be utilized.

Mailgun for WordPress

The Mailgun for WordPress plugin for WordPress is vulnerable to Server-Side Request Forgery (SSRF) via path traversal in versions up to and including 2.2.0. This is due to insufficient input validation in the add_list() function, which accepts user-controlled array keys from $_POST['addresses'], passes them through sanitize_text_field(). This makes it possible for unauthenticated attackers to make authenticated POST requests to any Mailgun API endpoint using the WordPress site's API key, including creating inbound email-forwarding routes that can intercept password reset emails, leading to administrator account takeover.

Google Cloud Application Integration

A Missing Authorization vulnerability in the QueryEngineTask of Google Cloud Application Integration (versions from 2025-04-28 to 2026-04-04) allows an external attacker to access sensitive internal data. The issue was patched on April 4, 2026; no customer action is required.

Unknown SmilePass Selfie Login

The SmilePass Selfie Login WordPress plugin through 1.0.2 does not perform any server-side verification of the identity it is asked to authenticate, allowing unauthenticated users to log in as any registered account, including administrators.

Unknown Social Login & Sharing buttons with Analytics By SoClever

The Social Login & Sharing buttons with Analytics By SoClever WordPress plugin through 1.2.0 does not perform any authentication, authorisation or nonce checks in one of its publicly accessible login handlers, allowing unauthenticated attackers to obtain a valid session as any existing user, including administrators. In the default case a session as the site's original administrator account is obtained without needing to know any account details at all.

Unknown WP Social Media Login

The WP Social Media Login WordPress plugin through 1.0.6 does not verify that a social login was actually completed with the identity provider before authenticating a visitor, allowing unauthenticated attackers to log in as any existing user, including administrators, by supplying that user's email address.

4xmen xshop

xShop is an open-source shop developed in Laravel. An Unrestricted File Upload vulnerability in xShop version 3.0.3 allows an authenticated administrator to upload executable files (e.g., .php). By uploading a specially crafted php file, an attacker can achieve Remote Code Execution (RCE) on the server, leading to a full system compromise. Version 3.0.4 fixes the issue.