Semaine du 27 avril au 3 mai 2026

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: net: correctly handle tunneled traffic on IPV6_CSUM GSO fallback NETIF_F_IPV6_CSUM only advertises support for checksum offload of packets without IPv6 extension headers. Packets with extension headers must fall back onto software checksumming. Since TSO depends on checksum offload, those must revert to GSO. The below commit introduces that fallback. It always checks network header length. For tunneled packets, the inner header length must be checked instead. Extend the check accordingly. A special case is tunneled packets without inner IP protocol. Such as RFC 6951 SCTP in UDP. Those are not standard IPv6 followed by transport header either, so also must revert to the software GSO path.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: net: mana: fix use-after-free in add_adev() error path If auxiliary_device_add() fails, add_adev() jumps to add_fail and calls auxiliary_device_uninit(adev). The auxiliary device has its release callback set to adev_release(), which frees the containing struct mana_adev. Since adev is embedded in struct mana_adev, the subsequent fall-through to init_fail and access to adev->id may result in a use-after-free. Fix this by saving the allocated auxiliary device id in a local variable before calling auxiliary_device_add(), and use that saved id in the cleanup path after auxiliary_device_uninit().

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: scsi: target: file: Use kzalloc_flex for aio_cmd The target_core_file doesn't initialize the aio_cmd->iocb for the ki_write_stream. When a write command fd_execute_rw_aio() is executed, we may get a bogus ki_write_stream value, causing unintended write failure status when checking iocb->ki_write_stream > max_write_streams in the block device. Let's just use kzalloc_flex when allocating the aio_cmd and let ki_write_stream=0 to fix this issue.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: check tdls flag in ieee80211_tdls_oper When NL80211_TDLS_ENABLE_LINK is called, the code only checks if the station exists but not whether it is actually a TDLS station. This allows the operation to proceed for non-TDLS stations, causing unintended side effects like modifying channel context and HT protection before failing. Add a check for sta->sta.tdls early in the ENABLE_LINK case, before any side effects occur, to ensure the operation is only allowed for actual TDLS peers.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: HID: wacom: fix out-of-bounds read in wacom_intuos_bt_irq The wacom_intuos_bt_irq() function processes Bluetooth HID reports without sufficient bounds checking. A maliciously crafted short report can trigger an out-of-bounds read when copying data into the wacom structure. Specifically, report 0x03 requires at least 22 bytes to safely read the processed data and battery status, while report 0x04 (which falls through to 0x03) requires 32 bytes. Add explicit length checks for these report IDs and log a warning if a short report is received.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: atm: lec: fix use-after-free in sock_def_readable() A race condition exists between lec_atm_close() setting priv->lecd to NULL and concurrent access to priv->lecd in send_to_lecd(), lec_handle_bridge(), and lec_atm_send(). When the socket is freed via RCU while another thread is still using it, a use-after-free occurs in sock_def_readable() when accessing the socket's wait queue. The root cause is that lec_atm_close() clears priv->lecd without any synchronization, while callers dereference priv->lecd without any protection against concurrent teardown. Fix this by converting priv->lecd to an RCU-protected pointer: - Mark priv->lecd as __rcu in lec.h - Use rcu_assign_pointer() in lec_atm_close() and lecd_attach() for safe pointer assignment - Use rcu_access_pointer() for NULL checks that do not dereference the pointer in lec_start_xmit(), lec_push(), send_to_lecd() and lecd_attach() - Use rcu_read_lock/rcu_dereference/rcu_read_unlock in send_to_lecd(), lec_handle_bridge() and lec_atm_send() to safely access lecd - Use rcu_assign_pointer() followed by synchronize_rcu() in lec_atm_close() to ensure all readers have completed before proceeding. This is safe since lec_atm_close() is called from vcc_release() which holds lock_sock(), a sleeping lock. - Remove the manual sk_receive_queue drain from lec_atm_close() since vcc_destroy_socket() already drains it after lec_atm_close() returns. v2: Switch from spinlock + sock_hold/put approach to RCU to properly fix the race. The v1 spinlock approach had two issues pointed out by Eric Dumazet: 1. priv->lecd was still accessed directly after releasing the lock instead of using a local copy. 2. The spinlock did not prevent packets being queued after lec_atm_close() drains sk_receive_queue since timer and workqueue paths bypass netif_stop_queue(). Note: Syzbot patch testing was attempted but the test VM terminated unexpectedly with "Connection to localhost closed by remote host", likely due to a QEMU AHCI emulation issue unrelated to this fix. Compile testing with "make W=1 net/atm/lec.o" passes cleanly.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: HID: logitech-hidpp: Prevent use-after-free on force feedback initialisation failure Presently, if the force feedback initialisation fails when probing the Logitech G920 Driving Force Racing Wheel for Xbox One, an error number will be returned and propagated before the userspace infrastructure (sysfs and /dev/input) has been torn down. If userspace ignores the errors and continues to use its references to these dangling entities, a UAF will promptly follow. We have 2 options; continue to return the error, but ensure that all of the infrastructure is torn down accordingly or continue to treat this condition as a warning by emitting the message but returning success. It is thought that the original author's intention was to emit the warning but keep the device functional, less the force feedback feature, so let's go with that.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: HID: core: Mitigate potential OOB by removing bogus memset() The memset() in hid_report_raw_event() has the good intention of clearing out bogus data by zeroing the area from the end of the incoming data string to the assumed end of the buffer. However, as we have previously seen, doing so can easily result in OOB reads and writes in the subsequent thread of execution. The current suggestion from one of the HID maintainers is to remove the memset() and simply return if the incoming event buffer size is not large enough to fill the associated report. Suggested-by Benjamin Tissoires <bentiss@kernel.org> [bentiss: changed the return value]

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: Check to ensure report responses match the request It is possible for a malicious (or clumsy) device to respond to a specific report's feature request using a completely different report ID. This can cause confusion in the HID core resulting in nasty side-effects such as OOB writes. Add a check to ensure that the report ID in the response, matches the one that was requested. If it doesn't, omit reporting the raw event and return early.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: crypto: caam - fix DMA corruption on long hmac keys When a key longer than block size is supplied, it is copied and then hashed into the real key. The memory allocated for the copy needs to be rounded to DMA cache alignment, as otherwise the hashed key may corrupt neighbouring memory. The rounding was performed, but never actually used for the allocation. Fix this by replacing kmemdup with kmalloc for a larger buffer, followed by memcpy.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: mpls: add seqcount to protect the platform_label{,s} pair The RCU-protected codepaths (mpls_forward, mpls_dump_routes) can have an inconsistent view of platform_labels vs platform_label in case of a concurrent resize (resize_platform_label_table, under platform_mutex). This can lead to OOB accesses. This patch adds a seqcount, so that we get a consistent snapshot. Note that mpls_label_ok is also susceptible to this, so the check against RTA_DST in rtm_to_route_config, done outside platform_mutex, is not sufficient. This value gets passed to mpls_label_ok once more in both mpls_route_add and mpls_route_del, so there is no issue, but that additional check must not be removed.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: net: ipv6: ndisc: fix ndisc_ra_useropt to initialize nduseropt_padX fields to zero to prevent an info-leak When processing Router Advertisements with user options the kernel builds an RTM_NEWNDUSEROPT netlink message. The nduseroptmsg struct has three padding fields that are never zeroed and can leak kernel data The fix is simple, just zeroes the padding fields.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: crypto: authencesn - Do not place hiseq at end of dst for out-of-place decryption When decrypting data that is not in-place (src != dst), there is no need to save the high-order sequence bits in dst as it could simply be re-copied from the source. However, the data to be hashed need to be rearranged accordingly. Thanks,

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: net: xilinx: axienet: Fix BQL accounting for multi-BD TX packets When a TX packet spans multiple buffer descriptors (scatter-gather), axienet_free_tx_chain sums the per-BD actual length from descriptor status into a caller-provided accumulator. That sum is reset on each NAPI poll. If the BDs for a single packet complete across different polls, the earlier bytes are lost and never credited to BQL. This causes BQL to think bytes are permanently in-flight, eventually stalling the TX queue. The SKB pointer is stored only on the last BD of a packet. When that BD completes, use skb->len for the byte count instead of summing per-BD status lengths. This matches netdev_sent_queue(), which debits skb->len, and naturally survives across polls because no partial packet contributes to the accumulator.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix regsafe() for pointers to packet In case rold->reg->range == BEYOND_PKT_END && rcur->reg->range == N regsafe() may return true which may lead to current state with valid packet range not being explored. Fix the bug.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix soft lockup in mptcp_recvmsg() syzbot reported a soft lockup in mptcp_recvmsg() [0]. When receiving data with MSG_PEEK | MSG_WAITALL flags, the skb is not removed from the sk_receive_queue. This causes sk_wait_data() to always find available data and never perform actual waiting, leading to a soft lockup. Fix this by adding a 'last' parameter to track the last peeked skb. This allows sk_wait_data() to make informed waiting decisions and prevent infinite loops when MSG_PEEK is used. [0]: watchdog: BUG: soft lockup - CPU#2 stuck for 156s! [server:1963] Modules linked in: CPU: 2 UID: 0 PID: 1963 Comm: server Not tainted 6.19.0-rc8 #61 PREEMPT(none) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:sk_wait_data+0x15/0x190 Code: 80 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 41 56 41 55 41 54 49 89 f4 55 48 89 d5 53 48 89 fb <48> 83 ec 30 65 48 8b 05 17 a4 6b 01 48 89 44 24 28 31 c0 65 48 8b RSP: 0018:ffffc90000603ca0 EFLAGS: 00000246 RAX: 0000000000000000 RBX: ffff888102bf0800 RCX: 0000000000000001 RDX: 0000000000000000 RSI: ffffc90000603d18 RDI: ffff888102bf0800 RBP: 0000000000000000 R08: 0000000000000002 R09: 0000000000000101 R10: 0000000000000000 R11: 0000000000000075 R12: ffffc90000603d18 R13: ffff888102bf0800 R14: ffff888102bf0800 R15: 0000000000000000 FS: 00007f6e38b8c4c0(0000) GS:ffff8881b877e000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055aa7bff1680 CR3: 0000000105cbe000 CR4: 00000000000006f0 Call Trace: <TASK> mptcp_recvmsg+0x547/0x8c0 net/mptcp/protocol.c:2329 inet_recvmsg+0x11f/0x130 net/ipv4/af_inet.c:891 sock_recvmsg+0x94/0xc0 net/socket.c:1100 __sys_recvfrom+0xb2/0x130 net/socket.c:2256 __x64_sys_recvfrom+0x1f/0x30 net/socket.c:2267 do_syscall_64+0x59/0x2d0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e arch/x86/entry/entry_64.S:131 RIP: 0033:0x7f6e386a4a1d Code: 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8d 05 f1 de 2c 00 41 89 ca 8b 00 85 c0 75 20 45 31 c9 45 31 c0 b8 2d 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 6b f3 c3 66 0f 1f 84 00 00 00 00 00 41 56 41 RSP: 002b:00007ffc3c4bb078 EFLAGS: 00000246 ORIG_RAX: 000000000000002d RAX: ffffffffffffffda RBX: 000000000000861e RCX: 00007f6e386a4a1d RDX: 00000000000003ff RSI: 00007ffc3c4bb150 RDI: 0000000000000004 RBP: 00007ffc3c4bb570 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000103 R11: 0000000000000246 R12: 00005605dbc00be0 R13: 00007ffc3c4bb650 R14: 0000000000000000 R15: 0000000000000000 </TASK>

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: netfilter: x_tables: ensure names are nul-terminated Reject names that lack a \0 character before feeding them to functions that expect c-strings. Fixes tag is the most recent commit that needs this change.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conntrack_helper: pass helper to expect cleanup nf_conntrack_helper_unregister() calls nf_ct_expect_iterate_destroy() to remove expectations belonging to the helper being unregistered. However, it passes NULL instead of the helper pointer as the data argument, so expect_iter_me() never matches any expectation and all of them survive the cleanup. After unregister returns, nfnl_cthelper_del() frees the helper object immediately. Subsequent expectation dumps or packet-driven init_conntrack() calls then dereference the freed exp->helper, causing a use-after-free. Pass the actual helper pointer so expectations referencing it are properly destroyed before the helper object is freed. BUG: KASAN: slab-use-after-free in string+0x38f/0x430 Read of size 1 at addr ffff888003b14d20 by task poc/103 Call Trace: string+0x38f/0x430 vsnprintf+0x3cc/0x1170 seq_printf+0x17a/0x240 exp_seq_show+0x2e5/0x560 seq_read_iter+0x419/0x1280 proc_reg_read+0x1ac/0x270 vfs_read+0x179/0x930 ksys_read+0xef/0x1c0 Freed by task 103: The buggy address is located 32 bytes inside of freed 192-byte region [ffff888003b14d00, ffff888003b14dc0)

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: netfilter: ctnetlink: ignore explicit helper on new expectations Use the existing master conntrack helper, anything else is not really supported and it just makes validation more complicated, so just ignore what helper userspace suggests for this expectation. This was uncovered when validating CTA_EXPECT_CLASS via different helper provided by userspace than the existing master conntrack helper: BUG: KASAN: slab-out-of-bounds in nf_ct_expect_related_report+0x2479/0x27c0 Read of size 4 at addr ffff8880043fe408 by task poc/102 Call Trace: nf_ct_expect_related_report+0x2479/0x27c0 ctnetlink_create_expect+0x22b/0x3b0 ctnetlink_new_expect+0x4bd/0x5c0 nfnetlink_rcv_msg+0x67a/0x950 netlink_rcv_skb+0x120/0x350 Allowing to read kernel memory bytes off the expectation boundary. CTA_EXPECT_HELP_NAME is still used to offer the helper name to userspace via netlink dump.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: SCO: fix race conditions in sco_sock_connect() sco_sock_connect() checks sk_state and sk_type without holding the socket lock. Two concurrent connect() syscalls on the same socket can both pass the check and enter sco_connect(), leading to use-after-free. The buggy scenario involves three participants and was confirmed with additional logging instrumentation: Thread A (connect): HCI disconnect: Thread B (connect): sco_sock_connect(sk) sco_sock_connect(sk) sk_state==BT_OPEN sk_state==BT_OPEN (pass, no lock) (pass, no lock) sco_connect(sk): sco_connect(sk): hci_dev_lock hci_dev_lock hci_connect_sco <- blocked -> hcon1 sco_conn_add->conn1 lock_sock(sk) sco_chan_add: conn1->sk = sk sk->conn = conn1 sk_state=BT_CONNECT release_sock hci_dev_unlock hci_dev_lock sco_conn_del: lock_sock(sk) sco_chan_del: sk->conn=NULL conn1->sk=NULL sk_state= BT_CLOSED SOCK_ZAPPED release_sock hci_dev_unlock (unblocked) hci_connect_sco -> hcon2 sco_conn_add -> conn2 lock_sock(sk) sco_chan_add: sk->conn=conn2 sk_state= BT_CONNECT // zombie sk! release_sock hci_dev_unlock Thread B revives a BT_CLOSED + SOCK_ZAPPED socket back to BT_CONNECT. Subsequent cleanup triggers double sock_put() and use-after-free. Meanwhile conn1 is leaked as it was orphaned when sco_conn_del() cleared the association. Fix this by: - Moving lock_sock() before the sk_state/sk_type checks in sco_sock_connect() to serialize concurrent connect attempts - Fixing the sk_type != SOCK_SEQPACKET check to actually return the error instead of just assigning it - Adding a state re-check in sco_connect() after lock_sock() to catch state changes during the window between the locks - Adding sco_pi(sk)->conn check in sco_chan_add() to prevent double-attach of a socket to multiple connections - Adding hci_conn_drop() on sco_chan_add failure to prevent HCI connection leaks

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: validate LTK enc_size on load Load Long Term Keys stores the user-provided enc_size and later uses it to size fixed-size stack operations when replying to LE LTK requests. An enc_size larger than the 16-byte key buffer can therefore overflow the reply stack buffer. Reject oversized enc_size values while validating the management LTK record so invalid keys never reach the stored key state.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_conn: fix potential UAF in set_cig_params_sync hci_conn lookup and field access must be covered by hdev lock in set_cig_params_sync, otherwise it's possible it is freed concurrently. Take hdev lock to prevent hci_conn from being deleted or modified concurrently. Just RCU lock is not suitable here, as we also want to avoid "tearing" in the configuration.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_event: fix potential UAF in hci_le_remote_conn_param_req_evt hci_conn lookup and field access must be covered by hdev lock in hci_le_remote_conn_param_req_evt, otherwise it's possible it is freed concurrently. Extend the hci_dev_lock critical section to cover all conn usage.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: bpf: sockmap: Fix use-after-free of sk->sk_socket in sk_psock_verdict_data_ready(). syzbot reported use-after-free of AF_UNIX socket's sk->sk_socket in sk_psock_verdict_data_ready(). [0] In unix_stream_sendmsg(), the peer socket's ->sk_data_ready() is called after dropping its unix_state_lock(). Although the sender socket holds the peer's refcount, it does not prevent the peer's sock_orphan(), and the peer's sk_socket might be freed after one RCU grace period. Let's fetch the peer's sk->sk_socket and sk->sk_socket->ops under RCU in sk_psock_verdict_data_ready(). [0]: BUG: KASAN: slab-use-after-free in sk_psock_verdict_data_ready+0xec/0x590 net/core/skmsg.c:1278 Read of size 8 at addr ffff8880594da860 by task syz.4.1842/11013 CPU: 1 UID: 0 PID: 11013 Comm: syz.4.1842 Not tainted syzkaller #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2026 Call Trace: <TASK> dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xba/0x230 mm/kasan/report.c:482 kasan_report+0x117/0x150 mm/kasan/report.c:595 sk_psock_verdict_data_ready+0xec/0x590 net/core/skmsg.c:1278 unix_stream_sendmsg+0x8a3/0xe80 net/unix/af_unix.c:2482 sock_sendmsg_nosec net/socket.c:721 [inline] __sock_sendmsg net/socket.c:736 [inline] ____sys_sendmsg+0x972/0x9f0 net/socket.c:2585 ___sys_sendmsg+0x2a5/0x360 net/socket.c:2639 __sys_sendmsg net/socket.c:2671 [inline] __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x1bd/0x2a0 net/socket.c:2674 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x14d/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7facf899c819 Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007facf9827028 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007facf8c15fa0 RCX: 00007facf899c819 RDX: 0000000000000000 RSI: 0000200000000500 RDI: 0000000000000004 RBP: 00007facf8a32c91 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007facf8c16038 R14: 00007facf8c15fa0 R15: 00007ffd41b01c78 </TASK> Allocated by task 11013: kasan_save_stack mm/kasan/common.c:57 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:78 unpoison_slab_object mm/kasan/common.c:340 [inline] __kasan_slab_alloc+0x6c/0x80 mm/kasan/common.c:366 kasan_slab_alloc include/linux/kasan.h:253 [inline] slab_post_alloc_hook mm/slub.c:4538 [inline] slab_alloc_node mm/slub.c:4866 [inline] kmem_cache_alloc_lru_noprof+0x2b8/0x640 mm/slub.c:4885 sock_alloc_inode+0x28/0xc0 net/socket.c:316 alloc_inode+0x6a/0x1b0 fs/inode.c:347 new_inode_pseudo include/linux/fs.h:3003 [inline] sock_alloc net/socket.c:631 [inline] __sock_create+0x12d/0x9d0 net/socket.c:1562 sock_create net/socket.c:1656 [inline] __sys_socketpair+0x1c4/0x560 net/socket.c:1803 __do_sys_socketpair net/socket.c:1856 [inline] __se_sys_socketpair net/socket.c:1853 [inline] __x64_sys_socketpair+0x9b/0xb0 net/socket.c:1853 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x14d/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Freed by task 15: kasan_save_stack mm/kasan/common.c:57 [inline] kasan_save_track+0x3e/0x80 mm/kasan/common.c:78 kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:584 poison_slab_object mm/kasan/common.c:253 [inline] __kasan_slab_free+0x5c/0x80 mm/kasan/common.c:285 kasan_slab_free include/linux/kasan.h:235 [inline] slab_free_hook mm/slub.c:2685 [inline] slab_free mm/slub.c:6165 [inline] kmem_cache_free+0x187/0x630 mm/slub.c:6295 rcu_do_batch kernel/rcu/tree.c: ---truncated---

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: net: macb: fix clk handling on PCI glue driver removal platform_device_unregister() may still want to use the registered clks during runtime resume callback. Note that there is a commit d82d5303c4c5 ("net: macb: fix use after free on rmmod") that addressed the similar problem of clk vs platform device unregistration but just moved the bug to another place. Save the pointers to clks into local variables for reuse after platform device is unregistered. BUG: KASAN: use-after-free in clk_prepare+0x5a/0x60 Read of size 8 at addr ffff888104f85e00 by task modprobe/597 CPU: 2 PID: 597 Comm: modprobe Not tainted 6.1.164+ #114 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.1-0-g3208b098f51a-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x8d/0xba print_report+0x17f/0x496 kasan_report+0xd9/0x180 clk_prepare+0x5a/0x60 macb_runtime_resume+0x13d/0x410 [macb] pm_generic_runtime_resume+0x97/0xd0 __rpm_callback+0xc8/0x4d0 rpm_callback+0xf6/0x230 rpm_resume+0xeeb/0x1a70 __pm_runtime_resume+0xb4/0x170 bus_remove_device+0x2e3/0x4b0 device_del+0x5b3/0xdc0 platform_device_del+0x4e/0x280 platform_device_unregister+0x11/0x50 pci_device_remove+0xae/0x210 device_remove+0xcb/0x180 device_release_driver_internal+0x529/0x770 driver_detach+0xd4/0x1a0 bus_remove_driver+0x135/0x260 driver_unregister+0x72/0xb0 pci_unregister_driver+0x26/0x220 __do_sys_delete_module+0x32e/0x550 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 </TASK> Allocated by task 519: kasan_save_stack+0x2c/0x50 kasan_set_track+0x21/0x30 __kasan_kmalloc+0x8e/0x90 __clk_register+0x458/0x2890 clk_hw_register+0x1a/0x60 __clk_hw_register_fixed_rate+0x255/0x410 clk_register_fixed_rate+0x3c/0xa0 macb_probe+0x1d8/0x42e [macb_pci] local_pci_probe+0xd7/0x190 pci_device_probe+0x252/0x600 really_probe+0x255/0x7f0 __driver_probe_device+0x1ee/0x330 driver_probe_device+0x4c/0x1f0 __driver_attach+0x1df/0x4e0 bus_for_each_dev+0x15d/0x1f0 bus_add_driver+0x486/0x5e0 driver_register+0x23a/0x3d0 do_one_initcall+0xfd/0x4d0 do_init_module+0x18b/0x5a0 load_module+0x5663/0x7950 __do_sys_finit_module+0x101/0x180 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Freed by task 597: kasan_save_stack+0x2c/0x50 kasan_set_track+0x21/0x30 kasan_save_free_info+0x2a/0x50 __kasan_slab_free+0x106/0x180 __kmem_cache_free+0xbc/0x320 clk_unregister+0x6de/0x8d0 macb_remove+0x73/0xc0 [macb_pci] pci_device_remove+0xae/0x210 device_remove+0xcb/0x180 device_release_driver_internal+0x529/0x770 driver_detach+0xd4/0x1a0 bus_remove_driver+0x135/0x260 driver_unregister+0x72/0xb0 pci_unregister_driver+0x26/0x220 __do_sys_delete_module+0x32e/0x550 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix incorrect pruning due to atomic fetch precision tracking When backtrack_insn encounters a BPF_STX instruction with BPF_ATOMIC and BPF_FETCH, the src register (or r0 for BPF_CMPXCHG) also acts as a destination, thus receiving the old value from the memory location. The current backtracking logic does not account for this. It treats atomic fetch operations the same as regular stores where the src register is only an input. This leads the backtrack_insn to fail to propagate precision to the stack location, which is then not marked as precise! Later, the verifier's path pruning can incorrectly consider two states equivalent when they differ in terms of stack state. Meaning, two branches can be treated as equivalent and thus get pruned when they should not be seen as such. Fix it as follows: Extend the BPF_LDX handling in backtrack_insn to also cover atomic fetch operations via is_atomic_fetch_insn() helper. When the fetch dst register is being tracked for precision, clear it, and propagate precision over to the stack slot. For non-stack memory, the precision walk stops at the atomic instruction, same as regular BPF_LDX. This covers all fetch variants. Before: 0: (b7) r1 = 8 ; R1=8 1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8 2: (b7) r2 = 0 ; R2=0 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm 4: (bf) r3 = r10 ; R3=fp0 R10=fp0 5: (0f) r3 += r2 mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1 mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10 mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) mark_precise: frame0: regs=r2 stack= before 2: (b7) r2 = 0 6: R2=8 R3=fp8 6: (b7) r0 = 0 ; R0=0 7: (95) exit After: 0: (b7) r1 = 8 ; R1=8 1: (7b) *(u64 *)(r10 -8) = r1 ; R1=8 R10=fp0 fp-8=8 2: (b7) r2 = 0 ; R2=0 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) ; R2=8 R10=fp0 fp-8=mmmmmmmm 4: (bf) r3 = r10 ; R3=fp0 R10=fp0 5: (0f) r3 += r2 mark_precise: frame0: last_idx 5 first_idx 0 subseq_idx -1 mark_precise: frame0: regs=r2 stack= before 4: (bf) r3 = r10 mark_precise: frame0: regs=r2 stack= before 3: (db) r2 = atomic64_fetch_add((u64 *)(r10 -8), r2) mark_precise: frame0: regs= stack=-8 before 2: (b7) r2 = 0 mark_precise: frame0: regs= stack=-8 before 1: (7b) *(u64 *)(r10 -8) = r1 mark_precise: frame0: regs=r1 stack= before 0: (b7) r1 = 8 6: R2=8 R3=fp8 6: (b7) r0 = 0 ; R0=0 7: (95) exit

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: accel/qaic: Handle DBC deactivation if the owner went away When a DBC is released, the device sends a QAIC_TRANS_DEACTIVATE_FROM_DEV transaction to the host over the QAIC_CONTROL MHI channel. QAIC handles this by calling decode_deactivate() to release the resources allocated for that DBC. Since that handling is done in the qaic_manage_ioctl() context, if the user goes away before receiving and handling the deactivation, the host will be out-of-sync with the DBCs available for use, and the DBC resources will not be freed unless the device is removed. If another user loads and requests to activate a network, then the device assigns the same DBC to that network, QAIC will "indefinitely" wait for dbc->in_use = false, leading the user process to hang. As a solution to this, handle QAIC_TRANS_DEACTIVATE_FROM_DEV transactions that are received after the user has gone away.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: io_uring/rsrc: reject zero-length fixed buffer import validate_fixed_range() admits buf_addr at the exact end of the registered region when len is zero, because the check uses strict greater-than (buf_end > imu->ubuf + imu->len). io_import_fixed() then computes offset == imu->len, which causes the bvec skip logic to advance past the last bio_vec entry and read bv_offset from out-of-bounds slab memory. Return early from io_import_fixed() when len is zero. A zero-length import has no data to transfer and should not walk the bvec array at all. BUG: KASAN: slab-out-of-bounds in io_import_reg_buf+0x697/0x7f0 Read of size 4 at addr ffff888002bcc254 by task poc/103 Call Trace: io_import_reg_buf+0x697/0x7f0 io_write_fixed+0xd9/0x250 __io_issue_sqe+0xad/0x710 io_issue_sqe+0x7d/0x1100 io_submit_sqes+0x86a/0x23c0 __do_sys_io_uring_enter+0xa98/0x1590 Allocated by task 103: The buggy address is located 12 bytes to the right of allocated 584-byte region [ffff888002bcc000, ffff888002bcc248)

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: hwmon: (tps53679) Fix array access with zero-length block read i2c_smbus_read_block_data() can return 0, indicating a zero-length read. When this happens, tps53679_identify_chip() accesses buf[ret - 1] which is buf[-1], reading one byte before the buffer on the stack. Fix by changing the check from "ret < 0" to "ret <= 0", treating a zero-length read as an error (-EIO), which prevents the out-of-bounds array access. Also fix a typo in the adjacent comment: "if present" instead of duplicate "if".

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: perf/x86: Fix potential bad container_of in intel_pmu_hw_config Auto counter reload may have a group of events with software events present within it. The software event PMU isn't the x86_hybrid_pmu and a container_of operation in intel_pmu_set_acr_caused_constr (via the hybrid helper) could cause out of bound memory reads. Avoid this by guarding the call to intel_pmu_set_acr_caused_constr with an is_x86_event check.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: fix u8 overflow in SSID scan buffer size calculation The variable valuesize is declared as u8 but accumulates the total length of all SSIDs to scan. Each SSID contributes up to 33 bytes (IEEE80211_MAX_SSID_LEN + 1), and with WILC_MAX_NUM_PROBED_SSID (10) SSIDs the total can reach 330, which wraps around to 74 when stored in a u8. This causes kmalloc to allocate only 75 bytes while the subsequent memcpy writes up to 331 bytes into the buffer, resulting in a 256-byte heap buffer overflow. Widen valuesize from u8 to u32 to accommodate the full range.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: fix potential out-of-bounds read in iwl_mvm_nd_match_info_handler() The memcpy function assumes the dynamic array notif->matches is at least as large as the number of bytes to copy. Otherwise, results->matches may contain unwanted data. To guarantee safety, extend the validation in one of the checks to ensure sufficient packet length. Found by Linux Verification Center (linuxtesting.org) with SVACE.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ALSA: caiaq: fix stack out-of-bounds read in init_card The loop creates a whitespace-stripped copy of the card shortname where `len < sizeof(card->id)` is used for the bounds check. Since sizeof(card->id) is 16 and the local id buffer is also 16 bytes, writing 16 non-space characters fills the entire buffer, overwriting the terminating nullbyte. When this non-null-terminated string is later passed to snd_card_set_id() -> copy_valid_id_string(), the function scans forward with `while (*nid && ...)` and reads past the end of the stack buffer, reading the contents of the stack. A USB device with a product name containing many non-ASCII, non-space characters (e.g. multibyte UTF-8) will reliably trigger this as follows: BUG: KASAN: stack-out-of-bounds in copy_valid_id_string sound/core/init.c:696 [inline] BUG: KASAN: stack-out-of-bounds in snd_card_set_id_no_lock+0x698/0x74c sound/core/init.c:718 The off-by-one has been present since commit bafeee5b1f8d ("ALSA: snd_usb_caiaq: give better shortname") from June 2009 (v2.6.31-rc1), which first introduced this whitespace-stripping loop. The original code never accounted for the null terminator when bounding the copy. Fix this by changing the loop bound to `sizeof(card->id) - 1`, ensuring at least one byte remains as the null terminator.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ALSA: ctxfi: Fix missing SPDIFI1 index handling SPDIF1 DAIO type isn't properly handled in daio_device_index() for hw20k2, and it returned -EINVAL, which ended up with the out-of-bounds array access. Follow the hw20k1 pattern and return the proper index for this type, too.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: io_uring/net: fix slab-out-of-bounds read in io_bundle_nbufs() sqe->len is __u32 but gets stored into sr->len which is int. When userspace passes sqe->len values exceeding INT_MAX (e.g. 0xFFFFFFFF), sr->len overflows to a negative value. This negative value propagates through the bundle recv/send path: 1. io_recv(): sel.val = sr->len (ssize_t gets -1) 2. io_recv_buf_select(): arg.max_len = sel->val (size_t gets 0xFFFFFFFFFFFFFFFF) 3. io_ring_buffers_peek(): buf->len is not clamped because max_len is astronomically large 4. iov[].iov_len = 0xFFFFFFFF flows into io_bundle_nbufs() 5. io_bundle_nbufs(): min_t(int, 0xFFFFFFFF, ret) yields -1, causing ret to increase instead of decrease, creating an infinite loop that reads past the allocated iov[] array This results in a slab-out-of-bounds read in io_bundle_nbufs() from the kmalloc-64 slab, as nbufs increments past the allocated iovec entries. BUG: KASAN: slab-out-of-bounds in io_bundle_nbufs+0x128/0x160 Read of size 8 at addr ffff888100ae05c8 by task exp/145 Call Trace: io_bundle_nbufs+0x128/0x160 io_recv_finish+0x117/0xe20 io_recv+0x2db/0x1160 Fix this by rejecting negative sr->len values early in both io_sendmsg_prep() and io_recvmsg_prep(). Since sqe->len is __u32, any value > INT_MAX indicates overflow and is not a valid length.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: SMP: derive legacy responder STK authentication from MITM state The legacy responder path in smp_random() currently labels the stored STK as authenticated whenever pending_sec_level is BT_SECURITY_HIGH. That reflects what the local service requested, not what the pairing flow actually achieved. For Just Works/Confirm legacy pairing, SMP_FLAG_MITM_AUTH stays clear and the resulting STK should remain unauthenticated even if the local side requested HIGH security. Use the established MITM state when storing the responder STK so the key metadata matches the pairing result. This also keeps the legacy path aligned with the Secure Connections code, which already treats JUST_WORKS/JUST_CFM as unauthenticated.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: fix stack buffer overflow in hci_le_big_create_sync hci_le_big_create_sync() uses DEFINE_FLEX to allocate a struct hci_cp_le_big_create_sync on the stack with room for 0x11 (17) BIS entries. However, conn->num_bis can hold up to HCI_MAX_ISO_BIS (31) entries — validated against ISO_MAX_NUM_BIS (0x1f) in the caller hci_conn_big_create_sync(). When conn->num_bis is between 18 and 31, the memcpy that copies conn->bis into cp->bis writes up to 14 bytes past the stack buffer, corrupting adjacent stack memory. This is trivially reproducible: binding an ISO socket with bc_num_bis = ISO_MAX_NUM_BIS (31) and calling listen() will eventually trigger hci_le_big_create_sync() from the HCI command sync worker, causing a KASAN-detectable stack-out-of-bounds write: BUG: KASAN: stack-out-of-bounds in hci_le_big_create_sync+0x256/0x3b0 Write of size 31 at addr ffffc90000487b48 by task kworker/u9:0/71 Fix this by changing the DEFINE_FLEX count from the incorrect 0x11 to HCI_MAX_ISO_BIS, which matches the maximum number of BIS entries that conn->bis can actually carry.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_event: move wake reason storage into validated event handlers hci_store_wake_reason() is called from hci_event_packet() immediately after stripping the HCI event header but before hci_event_func() enforces the per-event minimum payload length from hci_ev_table. This means a short HCI event frame can reach bacpy() before any bounds check runs. Rather than duplicating skb parsing and per-event length checks inside hci_store_wake_reason(), move wake-address storage into the individual event handlers after their existing event-length validation has succeeded. Convert hci_store_wake_reason() into a small helper that only stores an already-validated bdaddr while the caller holds hci_dev_lock(). Use the same helper after hci_event_func() with a NULL address to preserve the existing unexpected-wake fallback semantics when no validated event handler records a wake address. Annotate the helper with __must_hold(&hdev->lock) and add lockdep_assert_held(&hdev->lock) so future call paths keep the lock contract explicit. Call the helper from hci_conn_request_evt(), hci_conn_complete_evt(), hci_sync_conn_complete_evt(), le_conn_complete_evt(), hci_le_adv_report_evt(), hci_le_ext_adv_report_evt(), hci_le_direct_adv_report_evt(), hci_le_pa_sync_established_evt(), and hci_le_past_received_evt().

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: gpib: fix use-after-free in IO ioctl handlers The IBRD, IBWRT, IBCMD, and IBWAIT ioctl handlers use a gpib_descriptor pointer after board->big_gpib_mutex has been released. A concurrent IBCLOSEDEV ioctl can free the descriptor via close_dev_ioctl() during this window, causing a use-after-free. The IO handlers (read_ioctl, write_ioctl, command_ioctl) explicitly release big_gpib_mutex before calling their handler. wait_ioctl() is called with big_gpib_mutex held, but ibwait() releases it internally when wait_mask is non-zero. In all four cases, the descriptor pointer obtained from handle_to_descriptor() becomes unprotected. Fix this by introducing a kernel-only descriptor_busy reference count in struct gpib_descriptor. Each handler atomically increments descriptor_busy under file_priv->descriptors_mutex before releasing the lock, and decrements it when done. close_dev_ioctl() checks descriptor_busy under the same lock and rejects the close with -EBUSY if the count is non-zero. A reference count rather than a simple flag is necessary because multiple handlers can operate on the same descriptor concurrently (e.g. IBRD and IBWAIT on the same handle from different threads). A separate counter is needed because io_in_progress can be cleared from unprivileged userspace via the IBWAIT ioctl (through general_ibstatus() with set_mask containing CMPL), which would allow an attacker to bypass a check based solely on io_in_progress. The new descriptor_busy counter is only modified by the kernel IO paths. The lock ordering is consistent (big_gpib_mutex -> descriptors_mutex) and the handlers only hold descriptors_mutex briefly during the lookup, so there is no deadlock risk and no impact on IO throughput.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ti-adc161s626: use DMA-safe memory for spi_read() Add a DMA-safe buffer and use it for spi_read() instead of a stack memory. All SPI buffers must be DMA-safe. Since we only need up to 3 bytes, we just use a u8[] instead of __be16 and __be32 and change the conversion functions appropriately.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: validate doorbell_offset in user queue creation amdgpu_userq_get_doorbell_index() passes the user-provided doorbell_offset to amdgpu_doorbell_index_on_bar() without bounds checking. An arbitrarily large doorbell_offset can cause the calculated doorbell index to fall outside the allocated doorbell BO, potentially corrupting kernel doorbell space. Validate that doorbell_offset falls within the doorbell BO before computing the BAR index, using u64 arithmetic to prevent overflow. (cherry picked from commit de1ef4ffd70e1d15f0bf584fd22b1f28cbd5e2ec)

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: iio: imu: st_lsm6dsx: Set buffer sampling frequency for accelerometer only The st_lsm6dsx_hwfifo_odr_store() function, which is called when userspace writes the buffer sampling frequency sysfs attribute, calls st_lsm6dsx_check_odr(), which accesses the odr_table array at index `sensor->id`; since this array is only 2 entries long, an access for any sensor type other than accelerometer or gyroscope is an out-of-bounds access. The motivation for being able to set a buffer frequency different from the sensor sampling frequency is to support use cases that need accurate event detection (which requires a high sampling frequency) while retrieving sensor data at low frequency. Since all the supported event types are generated from acceleration data only, do not create the buffer sampling frequency attribute for sensor types other than the accelerometer.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIPLUS S7-1500 CPU 1518-4 PN/DP MFP

In the Linux kernel, the following vulnerability has been resolved: iio: gyro: mpu3050: Move iio_device_register() to correct location iio_device_register() should be at the end of the probe function to prevent race conditions. Place iio_device_register() at the end of the probe function and place iio_device_unregister() accordingly.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: usb: ulpi: fix double free in ulpi_register_interface() error path When device_register() fails, ulpi_register() calls put_device() on ulpi->dev. The device release callback ulpi_dev_release() drops the OF node reference and frees ulpi, but the current error path in ulpi_register_interface() then calls kfree(ulpi) again, causing a double free. Let put_device() handle the cleanup through ulpi_dev_release() and avoid freeing ulpi again in ulpi_register_interface().

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: usb: usbtmc: Flush anchored URBs in usbtmc_release When calling usbtmc_release, pending anchored URBs must be flushed or killed to prevent use-after-free errors (e.g. in the HCD giveback path). Call usbtmc_draw_down() to allow anchored URBs to be completed.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: comedi: me_daq: Fix potential overrun of firmware buffer `me2600_xilinx_download()` loads the firmware that was requested by `request_firmware()`. It is possible for it to overrun the source buffer because it blindly trusts the file format. It reads a data stream length from the first 4 bytes into variable `file_length` and reads the data stream contents of length `file_length` from offset 16 onwards. Although it checks that the supplied firmware is at least 16 bytes long, it does not check that it is long enough to contain the data stream. Add a test to ensure that the supplied firmware is long enough to contain the header and the data stream. On failure, log an error and return `-EINVAL`.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: comedi: me4000: Fix potential overrun of firmware buffer `me4000_xilinx_download()` loads the firmware that was requested by `request_firmware()`. It is possible for it to overrun the source buffer because it blindly trusts the file format. It reads a data stream length from the first 4 bytes into variable `file_length` and reads the data stream contents of length `file_length` from offset 16 onwards. Add a test to ensure that the supplied firmware is long enough to contain the header and the data stream. On failure, log an error and return `-EINVAL`. Note: The firmware loading was totally broken before commit ac584af59945 ("staging: comedi: me4000: fix firmware downloading"), but that is the most sensible target for this fix.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: reset: gpio: fix double free in reset_add_gpio_aux_device() error path When __auxiliary_device_add() fails, reset_add_gpio_aux_device() calls auxiliary_device_uninit(adev). The device release callback reset_gpio_aux_device_release() frees adev, but the current error path then calls kfree(adev) again, causing a double free. Keep kfree(adev) for the auxiliary_device_init() failure path, but avoid freeing adev after auxiliary_device_uninit().

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: nvmem: zynqmp_nvmem: Fix buffer size in DMA and memcpy Buffer size used in dma allocation and memcpy is wrong. It can lead to undersized DMA buffer access and possible memory corruption. use correct buffer size in dma_alloc_coherent and memcpy.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: vt: discard stale unicode buffer on alt screen exit after resize When enter_alt_screen() saves vc_uni_lines into vc_saved_uni_lines and sets vc_uni_lines to NULL, a subsequent console resize via vc_do_resize() skips reallocating the unicode buffer because vc_uni_lines is NULL. However, vc_saved_uni_lines still points to the old buffer allocated for the original dimensions. When leave_alt_screen() later restores vc_saved_uni_lines, the buffer dimensions no longer match vc_rows/vc_cols. Any operation that iterates over the unicode buffer using the current dimensions (e.g. csi_J clearing the screen) will access memory out of bounds, causing a kernel oops: BUG: unable to handle page fault for address: 0x0000002000000020 RIP: 0010:csi_J+0x133/0x2d0 The faulting address 0x0000002000000020 is two adjacent u32 space characters (0x20) interpreted as a pointer, read from the row data area past the end of the 25-entry pointer array in a buffer allocated for 80x25 but accessed with 240x67 dimensions. Fix this by checking whether the console dimensions changed while in the alternate screen. If they did, free the stale saved buffer instead of restoring it. The unicode screen will be lazily rebuilt via vc_uniscr_check() when next needed.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: crypto: tegra - Add missing CRYPTO_ALG_ASYNC The tegra crypto driver failed to set the CRYPTO_ALG_ASYNC on its asynchronous algorithms, causing the crypto API to select them for users that request only synchronous algorithms. This causes crashes (at least). Fix this by adding the flag like what the other drivers do. Also remove the unnecessary CRYPTO_ALG_TYPE_* flags, since those just get ignored and overridden by the registration function anyway.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: iommupt: Fix short gather if the unmap goes into a large mapping unmap has the odd behavior that it can unmap more than requested if the ending point lands within the middle of a large or contiguous IOPTE. In this case the gather should flush everything unmapped which can be larger than what was requested to be unmapped. The gather was only flushing the range requested to be unmapped, not extending to the extra range, resulting in a short invalidation if the caller hits this special condition. This was found by the new invalidation/gather test I am adding in preparation for ARMv8. Claude deduced the root cause. As far as I remember nothing relies on unmapping a large entry, so this is likely not a triggerable bug.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: thermal: core: Address thermal zone removal races with resume Since thermal_zone_pm_complete() and thermal_zone_device_resume() re-initialize the poll_queue delayed work for the given thermal zone, the cancel_delayed_work_sync() in thermal_zone_device_unregister() may miss some already running work items and the thermal zone may be freed prematurely [1]. There are two failing scenarios that both start with running thermal_pm_notify_complete() right before invoking thermal_zone_device_unregister() for one of the thermal zones. In the first scenario, there is a work item already running for the given thermal zone when thermal_pm_notify_complete() calls thermal_zone_pm_complete() for that thermal zone and it continues to run when thermal_zone_device_unregister() starts. Since the poll_queue delayed work has been re-initialized by thermal_pm_notify_complete(), the running work item will be missed by the cancel_delayed_work_sync() in thermal_zone_device_unregister() and if it continues to run past the freeing of the thermal zone object, a use-after-free will occur. In the second scenario, thermal_zone_device_resume() queued up by thermal_pm_notify_complete() runs right after the thermal_zone_exit() called by thermal_zone_device_unregister() has returned. The poll_queue delayed work is re-initialized by it before cancel_delayed_work_sync() is called by thermal_zone_device_unregister(), so it may continue to run after the freeing of the thermal zone object, which also leads to a use-after-free. Address the first failing scenario by ensuring that no thermal work items will be running when thermal_pm_notify_complete() is called. For this purpose, first move the cancel_delayed_work() call from thermal_zone_pm_complete() to thermal_zone_pm_prepare() to prevent new work from entering the workqueue going forward. Next, switch over to using a dedicated workqueue for thermal events and update the code in thermal_pm_notify() to flush that workqueue after thermal_pm_notify_prepare() has returned which will take care of all leftover thermal work already on the workqueue (that leftover work would do nothing useful anyway because all of the thermal zones have been flagged as suspended). The second failing scenario is addressed by adding a tz->state check to thermal_zone_device_resume() to prevent it from re-initializing the poll_queue delayed work if the thermal zone is going away. Note that the above changes will also facilitate relocating the suspend and resume of thermal zones closer to the suspend and resume of devices, respectively.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: possible double-free of cctx->remote_heap fastrpc_init_create_static_process() may free cctx->remote_heap on the err_map path but does not clear the pointer. Later, fastrpc_rpmsg_remove() frees cctx->remote_heap again if it is non-NULL, which can lead to a double-free if the INIT_CREATE_STATIC ioctl hits the error path and the rpmsg device is subsequently removed/unbound. Clear cctx->remote_heap after freeing it in the error path to prevent the later cleanup from freeing it again. This issue was found by an in-house analysis workflow that extracts AST-based information and runs static checks, with LLM assistance for triage, and was confirmed by manual code review. No hardware testing was performed.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: usb: typec: ucsi: validate connector number in ucsi_notify_common() The connector number extracted from CCI via UCSI_CCI_CONNECTOR() is a 7-bit field (0-127) that is used to index into the connector array in ucsi_connector_change(). However, the array is only allocated for the number of connectors reported by the device (typically 2-4 entries). A malicious or malfunctioning device could report an out-of-range connector number in the CCI, causing an out-of-bounds array access in ucsi_connector_change(). Add a bounds check in ucsi_notify_common(), the central point where CCI is parsed after arriving from hardware, so that bogus connector numbers are rejected before they propagate further.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_uac1_legacy: validate control request size f_audio_complete() copies req->length bytes into a 4-byte stack variable: u32 data = 0; memcpy(&data, req->buf, req->length); req->length is derived from the host-controlled USB request path, which can lead to a stack out-of-bounds write. Validate req->actual against the expected payload size for the supported control selectors and decode only the expected amount of data. This avoids copying a host-influenced length into a fixed-size stack object.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: crypto: krb5enc - fix async decrypt skipping hash verification krb5enc_dispatch_decrypt() sets req->base.complete as the skcipher callback, which is the caller's own completion handler. When the skcipher completes asynchronously, this signals "done" to the caller without executing krb5enc_dispatch_decrypt_hash(), completely bypassing the integrity verification (hash check). Compare with the encrypt path which correctly uses krb5enc_encrypt_done as an intermediate callback to chain into the hash computation on async completion. Fix by adding krb5enc_decrypt_done as an intermediate callback that chains into krb5enc_dispatch_decrypt_hash() upon async skcipher completion, matching the encrypt path's callback pattern. Also fix EBUSY/EINPROGRESS handling throughout: remove krb5enc_request_complete() which incorrectly swallowed EINPROGRESS notifications that must be passed up to callers waiting on backlogged requests, and add missing EBUSY checks in krb5enc_encrypt_ahash_done for the dispatch_encrypt return value. Unset MAY_BACKLOG on the async completion path so the user won't see back-to-back EINPROGRESS notifications.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate owner of durable handle on reconnect Currently, ksmbd does not verify if the user attempting to reconnect to a durable handle is the same user who originally opened the file. This allows any authenticated user to hijack an orphaned durable handle by predicting or brute-forcing the persistent ID. According to MS-SMB2, the server MUST verify that the SecurityContext of the reconnect request matches the SecurityContext associated with the existing open. Add a durable_owner structure to ksmbd_file to store the original opener's UID, GID, and account name. and catpure the owner information when a file handle becomes orphaned. and implementing ksmbd_vfs_compare_durable_owner() to validate the identity of the requester during SMB2_CREATE (DHnC).

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: validate rec->used in journal-replay file record check check_file_record() validates rec->total against the record size but never validates rec->used. The do_action() journal-replay handlers read rec->used from disk and use it to compute memmove lengths: DeleteAttribute: memmove(attr, ..., used - asize - roff) CreateAttribute: memmove(..., attr, used - roff) change_attr_size: memmove(..., used - PtrOffset(rec, next)) When rec->used is smaller than the offset of a validated attribute, or larger than the record size, these subtractions can underflow allowing us to copy huge amounts of memory in to a 4kb buffer, generally considered a bad idea overall. This requires a corrupted filesystem, which isn't a threat model the kernel really needs to worry about, but checking for such an obvious out-of-bounds value is good to keep things robust, especially on journal replay Fix this up by bounding rec->used correctly. This is much like commit b2bc7c44ed17 ("fs/ntfs3: Fix slab-out-of-bounds read in DeleteIndexEntryRoot") which checked different values in this same switch statement.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix UAF caused by decrementing sbi->nr_pages[] in f2fs_write_end_io() The xfstests case "generic/107" and syzbot have both reported a NULL pointer dereference. The concurrent scenario that triggers the panic is as follows: F2FS_WB_CP_DATA write callback umount - f2fs_write_checkpoint - f2fs_wait_on_all_pages(sbi, F2FS_WB_CP_DATA) - blk_mq_end_request - bio_endio - f2fs_write_end_io : dec_page_count(sbi, F2FS_WB_CP_DATA) : wake_up(&sbi->cp_wait) - kill_f2fs_super - kill_block_super - f2fs_put_super : iput(sbi->node_inode) : sbi->node_inode = NULL : f2fs_in_warm_node_list - is_node_folio // sbi->node_inode is NULL and panic The root cause is that f2fs_put_super() calls iput(sbi->node_inode) and sets sbi->node_inode to NULL after sbi->nr_pages[F2FS_WB_CP_DATA] is decremented to zero. As a result, f2fs_in_warm_node_list() may dereference a NULL node_inode when checking whether a folio belongs to the node inode, leading to a panic. This patch fixes the issue by calling f2fs_in_warm_node_list() before decrementing sbi->nr_pages[F2FS_WB_CP_DATA], thus preventing the use-after-free condition.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ksmbd: require minimum ACE size in smb_check_perm_dacl() Both ACE-walk loops in smb_check_perm_dacl() only guard against an under-sized remaining buffer, not against an ACE whose declared `ace->size` is smaller than the struct it claims to describe: if (offsetof(struct smb_ace, access_req) > aces_size) break; ace_size = le16_to_cpu(ace->size); if (ace_size > aces_size) break; The first check only requires the 4-byte ACE header to be in bounds; it does not require access_req (4 bytes at offset 4) to be readable. An attacker who has set a crafted DACL on a file they own can declare ace->size == 4 with aces_size == 4, pass both checks, and then granted |= le32_to_cpu(ace->access_req); /* upper loop */ compare_sids(&sid, &ace->sid); /* lower loop */ reads access_req at offset 4 (OOB by up to 4 bytes) and ace->sid at offset 8 (OOB by up to CIFS_SID_BASE_SIZE + SID_MAX_SUB_AUTHORITIES * 4 bytes). Tighten both loops to require ace_size >= offsetof(struct smb_ace, sid) + CIFS_SID_BASE_SIZE which is the smallest valid on-wire ACE layout (4-byte header + 4-byte access_req + 8-byte sid base with zero sub-auths). Also reject ACEs whose sid.num_subauth exceeds SID_MAX_SUB_AUTHORITIES before letting compare_sids() dereference sub_auth[] entries. parse_sec_desc() already enforces an equivalent check (lines 441-448); smb_check_perm_dacl() simply grew weaker validation over time. Reachability: authenticated SMB client with permission to set an ACL on a file. On a subsequent CREATE against that file, the kernel walks the stored DACL via smb_check_perm_dacl() and triggers the OOB read. Not pre-auth, and the OOB read is not reflected to the attacker, but KASAN reports and kernel state corruption are possible.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: smb: server: fix active_num_conn leak on transport allocation failure Commit 77ffbcac4e56 ("smb: server: fix leak of active_num_conn in ksmbd_tcp_new_connection()") addressed the kthread_run() failure path. The earlier alloc_transport() == NULL path in the same function has the same leak, is reachable pre-authentication via any TCP connect to port 445, and was empirically reproduced on UML (ARCH=um, v7.0-rc7): a small number of forced allocation failures were sufficient to put ksmbd into a state where every subsequent connection attempt was rejected for the remainder of the boot. ksmbd_kthread_fn() increments active_num_conn before calling ksmbd_tcp_new_connection() and discards the return value, so when alloc_transport() returns NULL the socket is released and -ENOMEM returned without decrementing the counter. Each such failure permanently consumes one slot from the max_connections pool; once cumulative failures reach the cap, atomic_inc_return() hits the threshold on every subsequent accept and every new connection is rejected. The counter is only reset by module reload. An unauthenticated remote attacker can drive the server toward the memory pressure that makes alloc_transport() fail by holding open connections with large RFC1002 lengths up to MAX_STREAM_PROT_LEN (0x00FFFFFF); natural transient allocation failures on a loaded host produce the same drift more slowly. Mirror the existing rollback pattern in ksmbd_kthread_fn(): on the alloc_transport() failure path, decrement active_num_conn gated on server_conf.max_connections. Repro details: with the patch reverted, forced alloc_transport() NULL returns leaked counter slots and subsequent connection attempts -- including legitimate connects issued after the forced-fail window had closed -- were all rejected with "Limit the maximum number of connections". With this patch applied, the same connect sequence produces no rejections and the counter cycles cleanly between zero and one on every accept.

Linux · Red Hat Enterprise Linux 10 · Red Hat Enterprise Linux 10.0 Extended Update Support · Red Hat Enterprise Linux 8

In the Linux kernel, the following vulnerability has been resolved: smb: client: validate the whole DACL before rewriting it in cifsacl build_sec_desc() and id_mode_to_cifs_acl() derive a DACL pointer from a server-supplied dacloffset and then use the incoming ACL to rebuild the chmod/chown security descriptor. The original fix only checked that the struct smb_acl header fits before reading dacl_ptr->size or dacl_ptr->num_aces. That avoids the immediate header-field OOB read, but the rewrite helpers still walk ACEs based on pdacl->num_aces with no structural validation of the incoming DACL body. A malicious server can return a truncated DACL that still contains a header, claims one or more ACEs, and then drive replace_sids_and_copy_aces() or set_chmod_dacl() past the validated extent while they compare or copy attacker-controlled ACEs. Factor the DACL structural checks into validate_dacl(), extend them to validate each ACE against the DACL bounds, and use the shared validator before the chmod/chown rebuild paths. parse_dacl() reuses the same validator so the read-side parser and write-side rewrite paths agree on what constitutes a well-formed incoming DACL.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix OOB read in smb2_ioctl_query_info QUERY_INFO path smb2_ioctl_query_info() has two response-copy branches: PASSTHRU_FSCTL and the default QUERY_INFO path. The QUERY_INFO branch clamps qi.input_buffer_length to the server-reported OutputBufferLength and then copies qi.input_buffer_length bytes from qi_rsp->Buffer to userspace, but it never verifies that the flexible-array payload actually fits within rsp_iov[1].iov_len. A malicious server can return OutputBufferLength larger than the actual QUERY_INFO response, causing copy_to_user() to walk past the response buffer and expose adjacent kernel heap to userspace. Guard the QUERY_INFO copy with a bounds check on the actual Buffer payload. Use struct_size(qi_rsp, Buffer, qi.input_buffer_length) rather than an open-coded addition so the guard cannot overflow on 32-bit builds.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate response sizes in ipc_validate_msg() ipc_validate_msg() computes the expected message size for each response type by adding (or multiplying) attacker-controlled fields from the daemon response to a fixed struct size in unsigned int arithmetic. Three cases can overflow: KSMBD_EVENT_RPC_REQUEST: msg_sz = sizeof(struct ksmbd_rpc_command) + resp->payload_sz; KSMBD_EVENT_SHARE_CONFIG_REQUEST: msg_sz = sizeof(struct ksmbd_share_config_response) + resp->payload_sz; KSMBD_EVENT_LOGIN_REQUEST_EXT: msg_sz = sizeof(struct ksmbd_login_response_ext) + resp->ngroups * sizeof(gid_t); resp->payload_sz is __u32 and resp->ngroups is __s32. Each addition can wrap in unsigned int; the multiplication by sizeof(gid_t) mixes signed and size_t, so a negative ngroups is converted to SIZE_MAX before the multiply. A wrapped value of msg_sz that happens to equal entry->msg_sz bypasses the size check on the next line, and downstream consumers (smb2pdu.c:6742 memcpy using rpc_resp->payload_sz, kmemdup in ksmbd_alloc_user using resp_ext->ngroups) then trust the unverified length. Use check_add_overflow() on the RPC_REQUEST and SHARE_CONFIG_REQUEST paths to detect integer overflow without constraining functional payload size; userspace ksmbd-tools grows NDR responses in 4096-byte chunks for calls like NetShareEnumAll, so a hard transport cap is unworkable on the response side. For LOGIN_REQUEST_EXT, reject resp->ngroups outside the signed [0, NGROUPS_MAX] range up front and report the error from ipc_validate_msg() so it fires at the IPC boundary; with that bound the subsequent multiplication and addition stay well below UINT_MAX. The now-redundant ngroups check and pr_err in ksmbd_alloc_user() are removed. This is the response-side analogue of aab98e2dbd64 ("ksmbd: fix integer overflows on 32 bit systems"), which hardened the request side.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate num_aces and harden ACE walk in smb_inherit_dacl() smb_inherit_dacl() trusts the on-disk num_aces value from the parent directory's DACL xattr and uses it to size a heap allocation: aces_base = kmalloc(sizeof(struct smb_ace) * num_aces * 2, ...); num_aces is a u16 read from le16_to_cpu(parent_pdacl->num_aces) without checking that it is consistent with the declared pdacl_size. An authenticated client whose parent directory's security.NTACL is tampered (e.g. via offline xattr corruption or a concurrent path that bypasses parse_dacl()) can present num_aces = 65535 with minimal actual ACE data. This causes a ~8 MB allocation (not kzalloc, so uninitialized) that the subsequent loop only partially populates, and may also overflow the three-way size_t multiply on 32-bit kernels. Additionally, the ACE walk loop uses the weaker offsetof(struct smb_ace, access_req) minimum size check rather than the minimum valid on-wire ACE size, and does not reject ACEs whose declared size is below the minimum. Reproduced on UML + KASAN + LOCKDEP against the real ksmbd code path. A legitimate mount.cifs client creates a parent directory over SMB (ksmbd writes a valid security.NTACL xattr), then the NTACL blob on the backing filesystem is rewritten to set num_aces = 0xFFFF while keeping the posix_acl_hash bytes intact so ksmbd_vfs_get_sd_xattr()'s hash check still passes. A subsequent SMB2 CREATE of a child under that parent drives smb2_open() into smb_inherit_dacl() (share has "vfs objects = acl_xattr" set), which fails the page allocator: WARNING: mm/page_alloc.c:5226 at __alloc_frozen_pages_noprof+0x46c/0x9c0 Workqueue: ksmbd-io handle_ksmbd_work __alloc_frozen_pages_noprof+0x46c/0x9c0 ___kmalloc_large_node+0x68/0x130 __kmalloc_large_node_noprof+0x24/0x70 __kmalloc_noprof+0x4c9/0x690 smb_inherit_dacl+0x394/0x2430 smb2_open+0x595d/0xabe0 handle_ksmbd_work+0x3d3/0x1140 With the patch applied the added guard rejects the tampered value with -EINVAL before any large allocation runs, smb2_open() falls back to smb2_create_sd_buffer(), and the child is created with a default SD. No warning, no splat. Fix by: 1. Validating num_aces against pdacl_size using the same formula applied in parse_dacl(). 2. Replacing the raw kmalloc(sizeof * num_aces * 2) with kmalloc_array(num_aces * 2, sizeof(...)) for overflow-safe allocation. 3. Tightening the per-ACE loop guard to require the minimum valid ACE size (offsetof(smb_ace, sid) + CIFS_SID_BASE_SIZE) and rejecting under-sized ACEs, matching the hardening in smb_check_perm_dacl() and parse_dacl(). v1 -> v2: - Replace the synthetic test-module splat in the changelog with a real-path UML + KASAN reproduction driven through mount.cifs and SMB2 CREATE; Namjae flagged the kcifs3_test_inherit_dacl_old name in v1 since it does not exist in ksmbd. - Drop the commit-hash citation from the code comment per Namjae's review; keep the parse_dacl() pointer.

Linux · Red Hat Enterprise Linux 10 · Red Hat Enterprise Linux 6 · Red Hat Enterprise Linux 7

In the Linux kernel, the following vulnerability has been resolved: writeback: Fix use after free in inode_switch_wbs_work_fn() inode_switch_wbs_work_fn() has a loop like: wb_get(new_wb); while (1) { list = llist_del_all(&new_wb->switch_wbs_ctxs); /* Nothing to do? */ if (!list) break; ... process the items ... } Now adding of items to the list looks like: wb_queue_isw() if (llist_add(&isw->list, &wb->switch_wbs_ctxs)) queue_work(isw_wq, &wb->switch_work); Because inode_switch_wbs_work_fn() loops when processing isw items, it can happen that wb->switch_work is pending while wb->switch_wbs_ctxs is empty. This is a problem because in that case wb can get freed (no isw items -> no wb reference) while the work is still pending causing use-after-free issues. We cannot just fix this by cancelling work when freeing wb because that could still trigger problematic 0 -> 1 transitions on wb refcount due to wb_get() in inode_switch_wbs_work_fn(). It could be all handled with more careful code but that seems unnecessarily complex so let's avoid that until it is proven that the looping actually brings practical benefit. Just remove the loop from inode_switch_wbs_work_fn() instead. That way when wb_queue_isw() queues work, we are guaranteed we have added the first item to wb->switch_wbs_ctxs and nobody is going to remove it (and drop the wb reference it holds) until the queued work runs.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix use-after-free of sbi in f2fs_compress_write_end_io() In f2fs_compress_write_end_io(), dec_page_count(sbi, type) can bring the F2FS_WB_CP_DATA counter to zero, unblocking f2fs_wait_on_all_pages() in f2fs_put_super() on a concurrent unmount CPU. The unmount path then proceeds to call f2fs_destroy_page_array_cache(sbi), which destroys sbi->page_array_slab via kmem_cache_destroy(), and eventually kfree(sbi). Meanwhile, the bio completion callback is still executing: when it reaches page_array_free(sbi, ...), it dereferences sbi->page_array_slab — a destroyed slab cache — to call kmem_cache_free(), causing a use-after-free. This is the same class of bug as CVE-2026-23234 (which fixed the equivalent race in f2fs_write_end_io() in data.c), but in the compressed writeback completion path that was not covered by that fix. Fix this by moving dec_page_count() to after page_array_free(), so that all sbi accesses complete before the counter decrement that can unblock unmount. For non-last folios (where atomic_dec_return on cic->pending_pages is nonzero), dec_page_count is called immediately before returning — page_array_free is not reached on this path, so there is no post-decrement sbi access. For the last folio, page_array_free runs while the F2FS_WB_CP_DATA counter is still nonzero (this folio has not yet decremented it), keeping sbi alive, and dec_page_count runs as the final operation.

Linux · Siemens SIMATIC S7-1500 CPU 1518-4 PN/DP MFP · Siemens SIMATIC S7-1500 CPU 1518F-4 PN/DP MFP · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem

In the Linux kernel, the following vulnerability has been resolved: net/packet: fix TOCTOU race on mmap'd vnet_hdr in tpacket_snd() In tpacket_snd(), when PACKET_VNET_HDR is enabled, vnet_hdr points directly into the mmap'd TX ring buffer shared with userspace. The kernel validates the header via __packet_snd_vnet_parse() but then re-reads all fields later in virtio_net_hdr_to_skb(). A concurrent userspace thread can modify the vnet_hdr fields between validation and use, bypassing all safety checks. The non-TPACKET path (packet_snd()) already correctly copies vnet_hdr to a stack-local variable. All other vnet_hdr consumers in the kernel (tun.c, tap.c, virtio_net.c) also use stack copies. The TPACKET TX path is the only caller of virtio_net_hdr_to_skb() that reads directly from user-controlled shared memory. Fix this by copying vnet_hdr from the mmap'd ring buffer to a stack-local variable before validation and use, consistent with the approach used in packet_snd() and all other callers.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp: Don't attempt to copy CSR to userspace if PSP command failed When retrieving the PEK CSR, don't attempt to copy the blob to userspace if the firmware command failed. If the failure was due to an invalid length, i.e. the userspace buffer+length was too small, copying the number of bytes _firmware_ requires will overflow the kernel-allocated buffer and leak data to userspace. BUG: KASAN: slab-out-of-bounds in instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] BUG: KASAN: slab-out-of-bounds in _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] BUG: KASAN: slab-out-of-bounds in _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 Read of size 2084 at addr ffff898144612e20 by task syz.9.219/21405 CPU: 14 UID: 0 PID: 21405 Comm: syz.9.219 Tainted: G U O 7.0.0-smp-DEV #28 PREEMPTLAZY Tainted: [U]=USER, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.62.0-0 11/19/2025 Call Trace: <TASK> dump_stack_lvl+0xc5/0x110 ../lib/dump_stack.c:120 print_address_description ../mm/kasan/report.c:378 [inline] print_report+0xbc/0x260 ../mm/kasan/report.c:482 kasan_report+0xa2/0xe0 ../mm/kasan/report.c:595 check_region_inline ../mm/kasan/generic.c:-1 [inline] kasan_check_range+0x264/0x2c0 ../mm/kasan/generic.c:200 instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 copy_to_user ../include/linux/uaccess.h:236 [inline] sev_ioctl_do_pek_csr+0x31f/0x590 ../drivers/crypto/ccp/sev-dev.c:1872 sev_ioctl+0x3a4/0x490 ../drivers/crypto/ccp/sev-dev.c:2562 vfs_ioctl ../fs/ioctl.c:51 [inline] __do_sys_ioctl ../fs/ioctl.c:597 [inline] __se_sys_ioctl+0x11d/0x1b0 ../fs/ioctl.c:583 do_syscall_x64 ../arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xe0/0x800 ../arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> WARN if the driver says the command succeeded, but the firmware error code says otherwise, as __sev_do_cmd_locked() is expected to return -EIO on any firwmware error.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp: Don't attempt to copy PDH cert to userspace if PSP command failed When retrieving the PDH cert, don't attempt to copy the blobs to userspace if the firmware command failed. If the failure was due to an invalid length, i.e. the userspace buffer+length was too small, copying the number of bytes _firmware_ requires will overflow the kernel-allocated buffer and leak data to userspace. BUG: KASAN: slab-out-of-bounds in instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] BUG: KASAN: slab-out-of-bounds in _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] BUG: KASAN: slab-out-of-bounds in _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 Read of size 2084 at addr ffff8885c4ab8aa0 by task syz.0.186/21033 CPU: 51 UID: 0 PID: 21033 Comm: syz.0.186 Tainted: G U O 7.0.0-smp-DEV #28 PREEMPTLAZY Tainted: [U]=USER, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 34.84.12-0 11/17/2025 Call Trace: <TASK> dump_stack_lvl+0xc5/0x110 ../lib/dump_stack.c:120 print_address_description ../mm/kasan/report.c:378 [inline] print_report+0xbc/0x260 ../mm/kasan/report.c:482 kasan_report+0xa2/0xe0 ../mm/kasan/report.c:595 check_region_inline ../mm/kasan/generic.c:-1 [inline] kasan_check_range+0x264/0x2c0 ../mm/kasan/generic.c:200 instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 copy_to_user ../include/linux/uaccess.h:236 [inline] sev_ioctl_do_pdh_export+0x3d3/0x7c0 ../drivers/crypto/ccp/sev-dev.c:2347 sev_ioctl+0x2a2/0x490 ../drivers/crypto/ccp/sev-dev.c:2568 vfs_ioctl ../fs/ioctl.c:51 [inline] __do_sys_ioctl ../fs/ioctl.c:597 [inline] __se_sys_ioctl+0x11d/0x1b0 ../fs/ioctl.c:583 do_syscall_x64 ../arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xe0/0x800 ../arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> WARN if the driver says the command succeeded, but the firmware error code says otherwise, as __sev_do_cmd_locked() is expected to return -EIO on any firwmware error.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp: Don't attempt to copy ID to userspace if PSP command failed When retrieving the ID for the CPU, don't attempt to copy the ID blob to userspace if the firmware command failed. If the failure was due to an invalid length, i.e. the userspace buffer+length was too small, copying the number of bytes _firmware_ requires will overflow the kernel-allocated buffer and leak data to userspace. BUG: KASAN: slab-out-of-bounds in instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] BUG: KASAN: slab-out-of-bounds in _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] BUG: KASAN: slab-out-of-bounds in _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 Read of size 64 at addr ffff8881867f5960 by task syz.0.906/24388 CPU: 130 UID: 0 PID: 24388 Comm: syz.0.906 Tainted: G U O 7.0.0-smp-DEV #28 PREEMPTLAZY Tainted: [U]=USER, [O]=OOT_MODULE Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.62.0-0 11/19/2025 Call Trace: <TASK> dump_stack_lvl+0xc5/0x110 ../lib/dump_stack.c:120 print_address_description ../mm/kasan/report.c:378 [inline] print_report+0xbc/0x260 ../mm/kasan/report.c:482 kasan_report+0xa2/0xe0 ../mm/kasan/report.c:595 check_region_inline ../mm/kasan/generic.c:-1 [inline] kasan_check_range+0x264/0x2c0 ../mm/kasan/generic.c:200 instrument_copy_to_user ../include/linux/instrumented.h:129 [inline] _inline_copy_to_user ../include/linux/uaccess.h:205 [inline] _copy_to_user+0x66/0xa0 ../lib/usercopy.c:26 copy_to_user ../include/linux/uaccess.h:236 [inline] sev_ioctl_do_get_id2+0x361/0x490 ../drivers/crypto/ccp/sev-dev.c:2222 sev_ioctl+0x25f/0x490 ../drivers/crypto/ccp/sev-dev.c:2575 vfs_ioctl ../fs/ioctl.c:51 [inline] __do_sys_ioctl ../fs/ioctl.c:597 [inline] __se_sys_ioctl+0x11d/0x1b0 ../fs/ioctl.c:583 do_syscall_x64 ../arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xe0/0x800 ../arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x76/0x7e </TASK> WARN if the driver says the command succeeded, but the firmware error code says otherwise, as __sev_do_cmd_locked() is expected to return -EIO on any firwmware error.

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix missing validation of ticket length in non-XDR key preparsing In rxrpc_preparse(), there are two paths for parsing key payloads: the XDR path (for large payloads) and the non-XDR path (for payloads <= 28 bytes). While the XDR path (rxrpc_preparse_xdr_rxkad()) correctly validates the ticket length against AFSTOKEN_RK_TIX_MAX, the non-XDR path fails to do so. This allows an unprivileged user to provide a very large ticket length. When this key is later read via rxrpc_read(), the total token size (toksize) calculation results in a value that exceeds AFSTOKEN_LENGTH_MAX, triggering a WARN_ON(). [ 2001.302904] WARNING: CPU: 2 PID: 2108 at net/rxrpc/key.c:778 rxrpc_read+0x109/0x5c0 [rxrpc] Fix this by adding a check in the non-XDR parsing path of rxrpc_preparse() to ensure the ticket length does not exceed AFSTOKEN_RK_TIX_MAX, bringing it into parity with the XDR parsing logic.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: wifi: virt_wifi: remove SET_NETDEV_DEV to avoid use-after-free Currently we execute `SET_NETDEV_DEV(dev, &priv->lowerdev->dev)` for the virt_wifi net devices. However, unregistering a virt_wifi device in netdev_run_todo() can happen together with the device referenced by SET_NETDEV_DEV(). It can result in use-after-free during the ethtool operations performed on a virt_wifi device that is currently being unregistered. Such a net device can have the `dev.parent` field pointing to the freed memory, but ethnl_ops_begin() calls `pm_runtime_get_sync(dev->dev.parent)`. Let's remove SET_NETDEV_DEV for virt_wifi to avoid bugs like this: ================================================================== BUG: KASAN: slab-use-after-free in __pm_runtime_resume+0xe2/0xf0 Read of size 2 at addr ffff88810cfc46f8 by task pm/606 Call Trace: <TASK> dump_stack_lvl+0x4d/0x70 print_report+0x170/0x4f3 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 kasan_report+0xda/0x110 ? __pm_runtime_resume+0xe2/0xf0 ? __pm_runtime_resume+0xe2/0xf0 __pm_runtime_resume+0xe2/0xf0 ethnl_ops_begin+0x49/0x270 ethnl_set_features+0x23c/0xab0 ? __pfx_ethnl_set_features+0x10/0x10 ? kvm_sched_clock_read+0x11/0x20 ? local_clock_noinstr+0xf/0xf0 ? local_clock+0x10/0x30 ? kasan_save_track+0x25/0x60 ? __kasan_kmalloc+0x7f/0x90 ? genl_family_rcv_msg_attrs_parse.isra.0+0x150/0x2c0 genl_family_rcv_msg_doit+0x1e7/0x2c0 ? __pfx_genl_family_rcv_msg_doit+0x10/0x10 ? __pfx_cred_has_capability.isra.0+0x10/0x10 ? stack_trace_save+0x8e/0xc0 genl_rcv_msg+0x411/0x660 ? __pfx_genl_rcv_msg+0x10/0x10 ? __pfx_ethnl_set_features+0x10/0x10 netlink_rcv_skb+0x121/0x380 ? __pfx_genl_rcv_msg+0x10/0x10 ? __pfx_netlink_rcv_skb+0x10/0x10 ? __pfx_down_read+0x10/0x10 genl_rcv+0x23/0x30 netlink_unicast+0x60f/0x830 ? __pfx_netlink_unicast+0x10/0x10 ? __pfx___alloc_skb+0x10/0x10 netlink_sendmsg+0x6ea/0xbc0 ? __pfx_netlink_sendmsg+0x10/0x10 ? __futex_queue+0x10b/0x1f0 ____sys_sendmsg+0x7a2/0x950 ? copy_msghdr_from_user+0x26b/0x430 ? __pfx_____sys_sendmsg+0x10/0x10 ? __pfx_copy_msghdr_from_user+0x10/0x10 ___sys_sendmsg+0xf8/0x180 ? __pfx____sys_sendmsg+0x10/0x10 ? __pfx_futex_wait+0x10/0x10 ? fdget+0x2e4/0x4a0 __sys_sendmsg+0x11f/0x1c0 ? __pfx___sys_sendmsg+0x10/0x10 do_syscall_64+0xe2/0x570 ? exc_page_fault+0x66/0xb0 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> This fix may be combined with another one in the ethtool subsystem: https://lore.kernel.org/all/20260322075917.254874-1-alex.popov@linux.com/T/#u

Linux · Siemens SIMATIC S7-1500 TM MFP - GNU/Linux subsystem · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: fuse: reject oversized dirents in page cache fuse_add_dirent_to_cache() computes a serialized dirent size from the server-controlled namelen field and copies the dirent into a single page-cache page. The existing logic only checks whether the dirent fits in the remaining space of the current page and advances to a fresh page if not. It never checks whether the dirent itself exceeds PAGE_SIZE. As a result, a malicious FUSE server can return a dirent with namelen=4095, producing a serialized record size of 4120 bytes. On 4 KiB page systems this causes memcpy() to overflow the cache page by 24 bytes into the following kernel page. Reject dirents that cannot fit in a single page before copying them into the readdir cache.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: cifs: some missing initializations on replay In several places in the code, we have a label to signify the start of the code where a request can be replayed if necessary. However, some of these places were missing the necessary reinitializations of certain local variables before replay. This change makes sure that these variables get initialized after the label.

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: xen/privcmd: fix double free via VMA splitting privcmd_vm_ops defines .close (privcmd_close), but neither .may_split nor .open. When userspace does a partial munmap() on a privcmd mapping, the kernel splits the VMA via __split_vma(). Since may_split is NULL, the split is allowed. vm_area_dup() copies vm_private_data (a pages array allocated in alloc_empty_pages()) into the new VMA without any fixup, because there is no .open callback. Both VMAs now point to the same pages array. When the unmapped portion is closed, privcmd_close() calls: - xen_unmap_domain_gfn_range() - xen_free_unpopulated_pages() - kvfree(pages) The surviving VMA still holds the dangling pointer. When it is later destroyed, the same sequence runs again, which leads to a double free. Fix this issue by adding a .may_split callback denying the VMA split. This is XSA-487 / CVE-2026-31787

Linux · Linux linux kernel

In the Linux kernel, the following vulnerability has been resolved: Buffer overflow in drivers/xen/sys-hypervisor.c The build id returned by HYPERVISOR_xen_version(XENVER_build_id) is neither NUL terminated nor a string. The first causes a buffer overflow as sprintf in buildid_show will read and copy till it finds a NUL. 00000000 f4 91 51 f4 dd 38 9e 9d 65 47 52 eb 10 71 db 50 |..Q..8..eGR..q.P| 00000010 b9 a8 01 42 6f 2e 32 |...Bo.2| 00000017 So use a memcpy instead of sprintf to have the correct value: 00000000 f4 91 51 f4 dd 00 9e 9d 65 47 52 eb 10 71 db 50 |..Q.....eGR..q.P| 00000010 b9 a8 01 42 |...B| 00000014 (the above have a hack to embed a zero inside and check it's returned correctly). This is XSA-485 / CVE-2026-31786