Mercredi 19 août 2026

Linux

In the Linux kernel, the following vulnerability has been resolved: net: mpls: initialize rtm_tos in mpls_getroute() mpls_getroute() builds the RTM_NEWROUTE reply to an RTM_GETROUTE request by filling a struct rtmsg allocated from an skb whose data area is not zeroed (alloc_skb(NLMSG_GOODSIZE, ...)). It sets every field of the header except rtm_tos: r = nlmsg_data(nlh); r->rtm_family = AF_MPLS; r->rtm_dst_len = 20; r->rtm_src_len = 0; r->rtm_table = RT_TABLE_MAIN; r->rtm_type = RTN_UNICAST; r->rtm_scope = RT_SCOPE_UNIVERSE; r->rtm_protocol = rt->rt_protocol; r->rtm_flags = 0; struct rtmsg has no padding, so the one uninitialised byte rtm_tos (offset 3) is copied straight to user space on recvmsg(), leaking a byte of uninitialised heap memory. This is in contrast to mpls_dump_route(), which fills the very same header and does set rtm_tos = 0. Initialize rtm_tos to 0, matching mpls_dump_route(). Reproduced with KMSAN by adding an MPLS route and issuing a non-RTM_F_FIB_MATCH RTM_GETROUTE for its label: BUG: KMSAN: kernel-infoleak in _copy_to_iter+0x36c/0x33f0 _copy_to_iter+0x36c/0x33f0 __skb_datagram_iter+0x196/0x12c0 skb_copy_datagram_iter+0x5b/0x210 netlink_recvmsg+0x37b/0xef0 ... Uninit was created at: __alloc_skb+0x8ca/0x10e0 mpls_getroute+0x1280/0x3a40 rtnetlink_rcv_msg+0x1138/0x15a0 ... Byte 19 of 64 is uninitialized (byte 19 = nlmsghdr(16) + rtmsg offset 3 = rtm_tos)

Linux

In the Linux kernel, the following vulnerability has been resolved: keys: make keyring key-chunk byte order agree with keyring_diff_objects() keyring_get_key_chunk() loads description bytes into the index chunk low address first, while keyring_diff_objects() numbers the first differing bit from the low end and folds the absolute byte index into the level without removing the inline-prefix offset the level already carries. The two disagree on byte order and bit position, so the array can be told two keys first differ at a bit that does not differ in the chunk the walker uses, letting crafted descriptions collide into one node. Load the chunk in the order keyring_diff_objects() assumes and drop the inline-prefix length when folding the byte index into the level. This only changes the in-memory ordering used to place keys within a keyring; add, search and read of non-colliding keys are unaffected.

Linux

In the Linux kernel, the following vulnerability has been resolved: scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake race Commit fbefe22811c3 ("scsi: libsas: Don't always drain event workqueue for HA resume") introduced sas_resume_ha_no_sync() to avoid a deadlock: the PHYE_RESUME_TIMEOUT handler, running on the HA event workqueue, calls sas_deform_port() -> sas_destruct_devices(), which removes SCSI devices and waits for the host to become runtime-active. But the host cannot resume until sas_resume_ha() -> sas_drain_work() returns, and the drain is blocked on that very handler. However skipping the drain reintroduces a race: hisi_sas returns from resume before all PHY UP work and libsas discovery work finish. The controller may then autosuspend while disks are still waking up. The disks issue IO to a suspended controller, the IO fails, and the disks get disabled. Fix the deadlock at its source by moving the PHYE_RESUME_TIMEOUT notification to after sas_drain_work(). By then the host resume is about to complete, so device removal through device_link no longer blocks on the resume and the cycle is broken. With the deadlock gone, restore sas_resume_ha() (the draining variant) in hisi_sas and remove sas_resume_ha_no_sync(). The reorder is safe for the other libsas consumers (isci, pm8001, aic94xx, mvsas). During suspend, sas_suspend_devices() calls sas_notify_lldd_dev_gone() for each device, which sets dev->lldd_dev to NULL. When scsi_unblock_requests re-enables I/O in resume, any I/O to a timed-out phy's disk is immediately rejected by the LLDD before reaching hardware: isci returns SAS_DEVICE_UNKNOWN (mapped to DID_BAD_TARGET), and pm8001 returns SAS_PHY_DOWN (mapped to DID_NO_CONNECT). Both complete directly via scsi_done() without entering SCSI EH. This is identical in both the old and new ordering since lldd_dev_gone runs during suspend, before resume. The reorder only affects when the PHYE_RESUME_TIMEOUT handler runs (synchronized by sas_drain_work() vs. asynchronous after resume returns), not whether I/O can reach the device. aic94xx and mvsas do not register any PM ops and never reach this code path.

Linux

In the Linux kernel, the following vulnerability has been resolved: hwmon: (nct6775-core) Fix number of temperature registers for NCT6116 Unlike NCT6106, NCT6116 only has three temperature registers, and with it only three temperature source and temperature source configuration registers. The register addresses match those of NCT6106 and can be re-used. The code used a separate array to list the temperature source registers for NCT6116, but used the size of the NCT6106 register array to set the number of registers. The NCT6106 register array provides six addresses, while the temperature source register array for NCT6116 only provides three addresses. This causes a KASAN report. BUG: KASAN: global-out-of-bounds in nct6775_probe+0x936/0x46f0 [nct6775] Read of size 2 at addr ffffffffc19561a6 by task modprobe/954 ... Call Trace: dump_stack+0x7d/0xa7 print_address_description.constprop.0+0x1c/0x220 ? __kasan_kmalloc.constprop.0+0xc9/0xd0 ? __kmalloc_node_track_caller+0x194/0x5b0 ? nct6775_probe+0x936/0x46f0 [nct6775] ? nct6775_probe+0x936/0x46f0 [nct6775] ... Fix the problem by hard-coding the number of temperature and temperature configuration registers to three for NCT6116. Drop the unnecessary NCT6116_REG_TEMP_SOURCE array and re-use NCT6106_REG_TEMP_SOURCE.

Linux

In the Linux kernel, the following vulnerability has been resolved: hwmon: (lm90) Only report alarms if driver is ready Userspace can read sysfs attributes before driver registration is complete, immediately after devm_hwmon_device_register_with_info() has been called. At that time, data->hwmon_dev is not yet initialized. This can trigger a NULL pointer access since lm90_update_device() and with it lm90_update_alarms_locked() will be called. This call schedules report_work and lm90_report_alarms(), which passes the still-NULL data->hwmon_dev to hwmon_notify_event() and triggers a NULL pointer dereference. Fix the problem by only scheduling the report and alert workers data->hwmon_dev is set.

Linux

In the Linux kernel, the following vulnerability has been resolved: hwmon: (adt7470) Fix busy-loop and I2C flooding in update thread When userspace configures 'auto_update_interval' to 0 via sysfs, the background kthread executes schedule_timeout_interruptible(0), which returns immediately. If 'num_temp_sensors' is concurrently or previously set to 0, the msleep_interruptible() delay inside adt7470_read_temperatures() also becomes 0. This combination forces the background thread into a tight, unbounded busy-loop, hogging the CPU and flooding the I2C bus with a continuous stream of transactions. Fix this vulnerability by raising the lower limit of the clamp_val in auto_update_interval_store() from 0 to 500 milliseconds. This guarantees a reasonable minimum sleep window between sensor updates, protecting the system from intentional or accidental I2C bus denial of service.

Linux

In the Linux kernel, the following vulnerability has been resolved: hwmon: (adt7470) Fix divide-by-zero TOCTOU crash in fan speed read If the fan data becomes 0 between the FAN_DATA_VALID() check and the FAN_PERIOD_TO_RPM() conversion, it will result in a divide-by-zero crash due to a race with a concurrent update of the cached fan value. Fix a TOCTOU issue by reading fan data once.

Linux

In the Linux kernel, the following vulnerability has been resolved: net: sxgbe: free TX rings on RX allocation failure When RX descriptor ring allocation fails, init_dma_desc_rings() only frees the partially allocated RX rings and returns. The TX rings that were allocated earlier in the same function are leaked. Rearrange error labels to clean up TX rings upon RX failures.

Linux

In the Linux kernel, the following vulnerability has been resolved: ALSA: 6fire: Fix UAF at error handling during probe Although 6fire driver had a few fixes for dealing with the early error handling during the probe phase, it forgot a pending URB before freeing the resources, which may lead to a UAF. This patch addresses it by doing the almost same cleanup procedure like the normal disconnect phase at the error path.

Linux

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: fix OOB write in snd_usbmidi_akai_output() snd_usbmidi_akai_output() computes its fill-loop bound buf_end = ep->max_transfer - MAX_AKAI_SYSEX_LEN - 1; as a signed int, so a small device-advertised bulk-OUT max_transfer makes buf_end negative. The loop guard then compares the u32 urb->transfer_buffer_length against that negative int: the usual arithmetic conversion turns buf_end into a large unsigned value, so the guard stays true and each iteration keeps appending SysEx framing and payload bytes past the end of the URB transfer buffer, which is only max_transfer bytes long. A USB device that advertises a tiny bulk-OUT endpoint can therefore trigger an attacker-length- and content-controlled heap out-of-bounds write when a process writes to the created /dev/snd/midiC*D* node. Return early when there is no room for even one SysEx, so the loop is never entered with a bound that would wrap. The loop is the last statement of the function, so bailing out is equivalent to it not running. Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com>

Linux

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix DMA buffer out-of-bounds write when fill_max is set When a USB audio endpoint requests full packet transfers via the fill_max descriptor flag, data_ep_set_params() promotes ep->curpacksize to ep->maxpacksize. However, maxsize is left at the original sample-rate derived value. Since u->buffer_size is allocated as maxsize * packets, the resulting DMA buffer is far too small for the requested transfer length. When the USB host controller streams up to curpacksize bytes per packet, it writes past the end of the buffer via DMA, corrupting kernel heap memory. Update maxsize to curpacksize when fill_max is set so that the allocated DMA buffer size matches the actual transfer request size. [ changed to reassign maxsize only when ep->fill_max is set -- tiwai ]

Linux

In the Linux kernel, the following vulnerability has been resolved: ublk: reset kernel-owned dev_info fields in ublk_ctrl_add_dev() ublk_ctrl_add_dev() memcpy()s the userspace ublksrv_ctrl_dev_info into ub->dev_info and then fixes up the fields the driver owns, but misses ->state and ->ublksrv_pid. A device added with ->state = UBLK_S_DEV_LIVE passes the "->state != UBLK_S_DEV_DEAD" test that ublk_stop_dev_unlocked() uses as its proxy for "a disk is attached", while ->ub_disk is still NULL, so DEL_DEV right after ADD_DEV oopses in del_gendisk(). UBLK_S_DEV_QUIESCED plus UBLK_F_USER_RECOVERY dies one step earlier, in ublk_force_abort_dev(). A poisoned ->state also gets START_USER_RECOVERY and the char device read/write path onto a device that was never started, and wedges START_DEV at -EEXIST. A poisoned ->ublksrv_pid just makes GET_DEV_INFO report an unrelated task as the ublk server. Reset both after the memcpy(), as ublk_detach_disk() does. Userspace only ever reads these back, so correcting them silently breaks nothing. ADD_DEV has copied ->state in unsanitized since ublk was merged, but back then it was harmless: the gendisk was allocated during ADD_DEV, and both teardown and the START_DEV -EEXIST check keyed off disk_live() rather than ->state. The oops became reachable once the disk allocation moved to START_DEV and those checks switched to ->state.

Linux

In the Linux kernel, the following vulnerability has been resolved: gpio: pch: use raw_spinlock_t for the register lock pch_irq_type() is registered as the irq_chip .irq_set_type callback and takes chip->spinlock with spin_lock_irqsave(). This callback is reached from __setup_irq() -> __irq_set_trigger() -> chip->irq_set_type() while the caller holds desc->lock, a raw_spinlock_t, with hardirqs disabled. That context is not sleepable, but on PREEMPT_RT a regular spinlock_t is an rtmutex-backed sleeping lock, so acquiring it there is invalid. This was confirmed on a PREEMPT_RT kernel with lockdep (PROVE_RAW_LOCK_NESTING and DEBUG_ATOMIC_SLEEP). A grounded PoC mirrored pch_irq_type()'s locking and drove it through the real genirq carrier irq_set_irq_type() -> __irq_set_trigger() -> chip->irq_set_type(), i.e. the same __irq_set_trigger() edge that __setup_irq() takes for a requested IRQ. With the original spin_lock_irqsave() edge lockdep reported an invalid wait context, immediately followed by: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 95, name: insmod hardirqs last disabled at (3784): _raw_spin_lock_irqsave+0x4f/0x60 rt_spin_lock+0x3a/0x1c0 repro_irq_set_type+0x64/0xa0 [pch_repro] __irq_set_trigger+0x69/0x140 irq_set_irq_type+0x78/0xd0 Switching the mirrored lock to raw_spinlock_t made both splats go away. Convert the register lock to raw_spinlock_t. The same lock also serializes the GPIO direction/value callbacks and the suspend/resume register save/restore, but all of those critical sections only perform MMIO register accesses (ioread32()/iowrite32()) and irq_set_handler_locked(); none of them contain sleepable operations. Keeping this register lock non-sleeping is therefore appropriate for the irqchip callbacks and does not change the GPIO-side locking contract. This is the same class of issue and fix as recently addressed for other GPIO controllers, e.g. commit 286533cb14a3 ("gpio: sch: use raw_spinlock_t in the irq startup path") and commit 90f0109019e6 ("gpio: eic-sprd: use raw_spinlock_t in the irq startup path").

Linux

In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: fix skb leak on flow key update failure during ct ovs_ct_execute() always steals or frees the skb on failure while ovs_flow_key_update() does not. So, if it fails and we return right away, the skb ends up leaked. Fix that by breaking instead and letting the common error handling code at the bottom of the loop to free the skb properly. This is a very unlikely scenario as it requires the packet to become unparseable by applying a set of actions on a previously parseable skb, but should be fixed nevertheless. Reported by Sashiko.

Linux

In the Linux kernel, the following vulnerability has been resolved: i2c: jz4780: Cache host clock rate at probe to prevent CCF prepare_lock deadlock Fix a severe AB/BA deadlock between the Common Clock Framework (CCF) and the I2C adapter lock, which triggers when an I2C-controlled clock generator client (like the Si5351) is registered or modified under the CCF. During an i2c client clock (generator) frequency change, the CCF acquires its global 'prepare_lock' mutex and the driver calls i2c_transfer() to update the client's chip registers, stalling for the adapter's I2C bus lock. Concurrently, an independent, parallel transfer on the same bus (e.g., a GPIO expander handling LEDs) can hold the I2C adapter lock. Inside this parallel transfer path, jz4780_i2c_set_speed() calls clk_get_rate() on the host controller's input clock to calculate bus timings. This call attempts to acquire the blocked CCF 'prepare_lock', creating a circular dependency that freezes the system. The jz4780 host controller clock itself is static and never changes at runtime. However, calling clk_get_rate() inside the active transfer path introduces an unnecessary dependency on the CCF internal locks. Eliminate this synchronous clk_get_rate() call from the active transfer path by caching the static host peripheral clock rate once - inside the private jz4780_i2c structure during jz4780_i2c_probe(). Update jz4780_i2c_set_speed() to use this cached value, safely decoupling active I2C transactions from the CCF internal locks without any risk of stale timings. Assisted-by web based Google AI (pinpointing the bug and writing the message).

Linux

In the Linux kernel, the following vulnerability has been resolved: can: etas_es58x: es58x_read_bulk_callback(): fix RX buffer leak on URB resubmit failure es58x_read_bulk_callback() resubmits the RX URB after processing a received packet. If the resubmit succeeds, the URB remains anchored and will be handled by the normal RX path or by teardown. However, if usb_submit_urb() fails, the callback unanchors the URB and then returns directly. This skips the existing free_urb path, so the coherent transfer buffer allocated with usb_alloc_coherent() is not released. Reuse the existing free_urb path after a resubmit failure so that the RX coherent buffer is freed before leaving the callback.

Linux

In the Linux kernel, the following vulnerability has been resolved: can: kvaser_usb_leaf: kvaser_usb_leaf_wait_cmd(): validate received command extents The wait and bulk receive paths walk variable-length commands from a USB buffer. A nonzero command shorter than CMD_HEADER_LEN can still be dispatched, and the wait path copies a matching command into a fixed caller-owned struct kvaser_cmd using the device-provided length. Reject nonzero commands that do not contain the fixed header or that extend beyond the current USB buffer item. In the wait path, also reject a matching command that exceeds the destination before copying it.

Linux

In the Linux kernel, the following vulnerability has been resolved: can: peak_usb: add bounds check for USB channel index The channel control index ctrl_idx is derived from rx->len which comes directly from a device USB payload. The mask 0x0f allows values 0-15, but the array size of usb_if->dev[] is only 2. Values 2-15 cause heap out-of-bounds read, eventually causing kernel panic in the IRQ context. Add bounds checking for ctrl_idx before the array access in both pcan_usb_pro_handle_canmsg() and pcan_usb_pro_handle_error().

Linux

In the Linux kernel, the following vulnerability has been resolved: can: peak_usb: validate uCAN receive record lengths pcan_usb_fd_decode_buf() walks uCAN records packed in one USB receive buffer. Require each record to contain the fixed header for its type, and verify CAN payload bytes before copying them into the skb.

Linux

In the Linux kernel, the following vulnerability has been resolved: ipv6: fib6: fix NULL deref in fib6_walk_continue() on multi-batch dump inet6_dump_fib() saves its progress in cb->args[1] as a positional index within the current hash chain. Between batches, a concurrent fib6_new_table() can insert a new table at the chain head, shifting all existing entries. The saved index then lands on a different table, causing fib6_dump_table() to set w->root to the wrong table while w->node still points into the previous one. fib6_walk_continue() dereferences w->node->parent (NULL) and panics: BUG: kernel NULL pointer dereference, address: 0000000000000008 RIP: 0010:fib6_walk_continue+0x6e/0x170 Call Trace: <TASK> fib6_dump_table.isra.0+0xc5/0x240 inet6_dump_fib+0xf6/0x420 rtnl_dumpit+0x30/0xa0 netlink_dump+0x15b/0x460 netlink_recvmsg+0x1d6/0x2a0 ____sys_recvmsg+0x17a/0x190 Fix by storing tb->tb6_id in cb->args[1] instead of a positional index. On resume, skip entries until the id matches; a concurrent head-insert can never match the saved id, so the walker always resumes on the correct table.

Linux

In the Linux kernel, the following vulnerability has been resolved: perf/x86/amd/brs: Fix kernel address leakage A user-only branch stack can contain branches that originate from the kernel. As a result, kernel addresses are exposed to user space even when PERF_SAMPLE_BRANCH_USER is requested. On AMD processors supporting X86_FEATURE_BRS (Zen 3 only), perf can still report entries such as SYSRET/interrupt returns for which the branch-from addresses are in the kernel. E.g. $ perf record -j any,u -c 4000 -e branch-brs -o - -- \ perf bench syscall basic --loop 1000 | \ perf script -i - -F brstack|tr ' ' '\n'| \ grep -E '0x[89a-f][0-9a-f]{15}' ... 0xffffffff810001c4/0x72e2e32955eb/-/-/-/0//- 0xffffffff810001c4/0x72e2d94a9821/-/-/-/0//- 0xffffffff810001c4/0x72e2d94ffa1b/-/-/-/0//- ... BRS provides no hardware branch filtering, so privilege level filtering is performed entirely in software. However, amd_brs_match_plm() only validates the branch-to address against the requested privilege levels. For branches from the kernel to user space, the branch-from address is left unchecked and is leaked. Extend the software filter to also validate the branch-from address, so that any branch record whose branch-from address is in the kernel is dropped when PERF_SAMPLE_BRANCH_USER is requested.

Linux

In the Linux kernel, the following vulnerability has been resolved: can: bcm: fix CAN frame rx/tx statistics KCSAN detected a data race within the bcm_rx_handler() when two CAN frames have been simultaneously received and processed in a single rx op by two different CPUs. Use atomic operations with (signed) long data types to access the statistics in the hot path to fix the KCSAN complaint. Additionally simplify the update and check of statistics overflow by using the atomic operations in separate bcm_update_[rx|tx]_stats() functions. The rx variant runs under bcm_rx_update_lock to prevent races when resetting the two rx counters; the tx variant runs under bcm_tx_lock and only needs to guard its own counter's overflow. As the rx path resets its values already at LONG_MAX / 100, there is no conflict between the two locking domains (bcm_rx_update_lock vs. bcm_tx_lock) even for ops that use both paths. The rx statistics update and the frames_filtered update in bcm_rx_changed() were previously performed in two separate bcm_rx_update_lock sections. For an rx op subscribed on all interfaces (ifindex == 0), bcm_rx_handler() can run concurrently on different CPUs, so a counter reset by one CPU between these two sections could leave frames_filtered larger than frames_abs on another CPU, producing a bogus (even negative) reduction percentage in procfs. Update the statistics in the same critical section as bcm_rx_changed() to close this gap, which also removes the now unneeded extra lock/unlock pair around the traffic_flags calculation.

Linux

In the Linux kernel, the following vulnerability has been resolved: can: bcm: fix data race on rx_stamp/rx_ifindex in bcm_rx_handler() For an rx op subscribed on all interfaces (ifindex == 0), the same op is registered once in the shared per-netns wildcard filter list, so bcm_rx_handler() can run concurrently on different CPUs for frames arriving on different net devices. op->rx_stamp and op->rx_ifindex were written before bcm_rx_update_lock was taken, allowing concurrent writers to race each other - including a torn store of the 64-bit rx_stamp on 32-bit platforms. Beyond a torn store bcm_send_to_user() must report the timestamp/ifindex of the very same frame whose content it is delivering. So the assignment is placed in the same unbroken bcm_rx_update_lock section as the content comparison. As a side effect, the RTR-request frame feature (which never reach bcm_send_to_user()) no longer updates rx_stamp/rx_ifindex, since only the notification path needs them.

Linux

In the Linux kernel, the following vulnerability has been resolved: btrfs: free mapping node on duplicate reloc root insert __add_reloc_root() allocates a mapping_node before inserting it into rc->reloc_root_tree. If rb_simple_insert() finds an existing entry, it returns the existing rb_node and leaves the newly allocated node unlinked. The error path then returns -EEXIST without freeing the new node. Since the node was never inserted into reloc_root_tree, the later cleanup in put_reloc_control() cannot find it either. Free the newly allocated node before returning -EEXIST. The callers currently assert that -EEXIST should not happen, so this is a defensive cleanup for an unexpected duplicate insert path. If the path is ever reached, the local allocation should still be released.

Linux

In the Linux kernel, the following vulnerability has been resolved: ata: sata_dwc_460ex: fix infinite loop in NCQ tag completion bit-scanning The hand-rolled bit-scanning loop in the NCQ completion path has an infinite loop bug. When tag_mask has only high bits set (e.g. 0x80000000), the inner while loop left-shifts tag_mask until it overflows to 0. At that point !(0 & 1) is always true and 0 <<= 1 stays 0, causing an infinite loop in hardirq context with a spinlock held. Replace the open-coded bit-scanning with __ffs() which correctly finds the least significant set bit and is bounded by the width of the argument.

Linux

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_ffa: Fix NULL dereference in ffa_partition_info_get() ffa_partition_info_get() passes uuid_str directly to uuid_parse() without a NULL check. When a caller passes NULL, uuid_parse() -> __uuid_parse() -> uuid_is_valid() dereferences the pointer, causing a kernel panic: | Unable to handle kernel NULL pointer dereference at virtual address | 0000000000000040 | pc : uuid_parse+0x40/0xac | lr : ffa_partition_info_get+0x1c/0x94 [arm_ffa] Add a NULL guard before uuid_parse() so a NULL argument returns -ENODEV instead of crashing. Callers are expected to always supply a valid partition UUID, so NULL is not a supported input.

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/gfx8: drop unecessary BUG_ON() There's no need to crash the kernel for this case. (cherry picked from commit 4d7c25208ca612b754f3bf39e9f16e725b828891)

Linux

In the Linux kernel, the following vulnerability has been resolved: KVM: x86/mmu: Fix use-after-free on vendor module reload mmu_destroy_caches() destroys pte_list_desc_cache and mmu_page_header_cache, but leaves both pointers unchanged. The pointers live in kvm.ko, and therefore survive when a vendor module is unloaded while kvm.ko remains loaded. If creation of pte_list_desc_cache fails during a subsequent vendor module load, its assignment sets pte_list_desc_cache to NULL and the error path calls mmu_destroy_caches(). mmu_page_header_cache still points to the cache destroyed during the preceding vendor module unload. Passing that stale pointer to kmem_cache_destroy() causes a slab use-after-free. Reproduce the issue on a v7.1.3 kernel with CONFIG_KASAN=y, CONFIG_KASAN_GENERIC=y, CONFIG_KVM=m, and CONFIG_KVM_INTEL=m. A one-shot test hook forces pte_list_desc_cache to NULL on the second invocation of kvm_mmu_vendor_module_init(): 1. Load kvm.ko and kvm-intel.ko, creating both caches. 2. Unload only kvm_intel, leaving kvm.ko loaded. 3. Reload kvm_intel and force initialization through the -ENOMEM path. KASAN reports: BUG: KASAN: slab-use-after-free in kvm_mmu_vendor_module_init+0x5b/0x170 [kvm] ... kmem_cache_destroy+0x21/0x1d0 kvm_mmu_vendor_module_init+0x5b/0x170 [kvm] ... Allocated by task 16817: __kmem_cache_create_args+0x12c/0x3b0 __kmem_cache_create.constprop.0+0xb6/0xf0 [kvm] kvm_mmu_vendor_module_init+0x13b/0x170 [kvm] ... Freed by task 16820: kmem_cache_destroy+0x117/0x1d0 kvm_mmu_vendor_module_exit+0x21/0x30 [kvm] Clear both pointers immediately after destroying their caches so that the stored state reflects the caches' lifetime and repeated cleanup is safe. With the fix applied, the same injected vendor module reload fails with -ENOMEM as expected and produces no KASAN report.

Linux

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix root leak if its reloc root is unexpected in merge_reloc_roots() If we have an unexpected reloc_root for our root, we jump to the out label but never drop the reference we obtained for root, resulting in a leak. Add a missing btrfs_put_root() call.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: ipw2100: fix potential memory leak in ipw2100_pci_init_one() The memory allocated in the ipw2100_alloc_device() function is not freed in some of the error paths in ipw2100_pci_init_one(). Fix that by converting the direct return into a goto to the error path return. The error path when pci_enable_device() fails cannot jump to fail, since at this point priv is not set, so perform error handling inline.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211_hwsim: clamp virtio RX length before skb_put hwsim_virtio_rx_work() passes the virtqueue used-ring length reported by the device straight to skb_put() on a fixed-size receive skb. A backend reporting a length larger than the skb tailroom drives skb_put() past the buffer end and hits skb_over_panic() -- a host-triggerable guest panic (denial of service). Clamp the length to the skb's available room before skb_put(). A conforming device never reports more than the posted buffer size, so valid frames are unaffected; a truncated over-report then fails the length/header checks in hwsim_virtio_handle_cmd() and is dropped, so truncating rather than dropping here cannot be turned into a parsing problem.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: libertas: fix memory leak in helper_firmware_cb() helper_firmware_cb() neglects to free the single-stage firmware image after a successful async load, leading to a memory leak in the USB firmware-download path. Fix this memory leak by calling release_firmware() immediately after lbs_fw_loaded() returns. The bug was first flagged by an experimental analysis tool we are developing for kernel memory-management bugs while analyzing v6.13-rc1. The tool is still under development and is not yet publicly available. Manual inspection confirms that the bug is still present in the current wireless tree. An x86_64 allyesconfig build showed no new warnings. As we do not have compatible Libertas USB hardware for exercising this firmware-download path, no runtime testing was able to be performed.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: nl80211: free RNR data on MBSSID mismatch nl80211_parse_beacon() rejects EMA RNR data when there are fewer RNR entries than MBSSID entries. The rejected RNR allocation has not been attached to the beacon data yet, so free it before returning the error.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: validate PMSR FTM preamble range PMSR FTM request parsing accepts preamble values outside the enumerated nl80211 preamble range. Reject out-of-range values before using them in the parser capability bit test using the policy. [drop unnecessary check]

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: free AP_VLAN bc_buf SKBs outside IRQ lock ieee80211_do_stop() removes AP_VLAN packets from the parent AP ps->bc_buf while holding ps->bc_buf.lock with IRQs disabled. It then calls ieee80211_free_txskb() before dropping the lock. ieee80211_free_txskb() is not just a passive SKB release. For SKBs with TX status state it can report a dropped frame through cfg80211/nl80211, and that path can reach netlink tap transmit. This is the same reason the pending queue cleanup in ieee80211_do_stop() already unlinks SKBs under the queue lock and frees them after IRQ state is restored. The buggy scenario involves two paths, with each column showing the order within that path: AP_VLAN management TX: AP_VLAN stop: 1. attach ACK-status state 1. clear the running state 2. queue a multicast SKB on 2. take ps->bc_buf.lock with IRQs parent ps->bc_buf disabled 3. unlink the AP_VLAN SKB 4. call ieee80211_free_txskb() Unlink matching AP_VLAN SKBs from ps->bc_buf under the existing lock, but move them to a local free queue. Drop the lock and restore IRQ state before calling ieee80211_free_txskb(). WARNING: kernel/softirq.c:430 at __local_bh_enable_ip

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: initialize SDIO data work before cleanup brcmf_sdio_probe() stores the newly allocated bus in sdiodev->bus before allocating the ordered workqueue. If that allocation fails, the function jumps to fail and calls brcmf_sdio_remove(). brcmf_sdio_remove() unconditionally cancels bus->datawork. Initialize the work item before the first failure path that can reach brcmf_sdio_remove(), so the cleanup path always observes a valid work object. This issue was found by our static analysis tool and then confirmed by manual review of the probe error path and the remove-time work drain. The problem pattern is an early setup failure that reaches a cleanup helper which cancels an embedded work item before its initializer has run. A QEMU PoC forced alloc_ordered_workqueue() to fail at the same point in brcmf_sdio_probe(), before INIT_WORK(&bus->datawork) is reached. The resulting fail path calls brcmf_sdio_remove(), and DEBUG_OBJECTS reports the invalid work drain with brcmf_sdio_probe() and brcmf_sdio_remove() in the stack.

Linux

In the Linux kernel, the following vulnerability has been resolved: ata: sata_dwc_460ex: enable SATA interrupts only after IRQ handler is registered sata_dwc_enable_interrupts() is called before platform_get_irq() and ata_host_activate(), leaving the SATA controller's interrupt mask enabled without a registered handler. If a later step fails (irq request, phy init, etc.) or if the controller asserts an interrupt during probe, the irq line may fire with no handler, causing a spurious interrupt storm. Move sata_dwc_enable_interrupts() after ata_host_activate() so that interrupts are only unmasked once the handler is registered and the core is fully initialized.

Linux

In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Reject unhashed UDP sockets on sockmap update UDP sockets get SOCK_RCU_FREE set when (auto-)bound. This means sk_is_refcounted(unbound) = true, while sk_is_refcounted(bound) = false. Because sockmap accepts unbound UDP sockets, a BPF program can increment a socket's refcount via lookup. If the socket is subsequently bound, the transition from unbound to bound causes bpf_sk_release() to skip the decrement of the refcount, causing a memory leak. unreferenced object 0xffff88810bc2eb40 (size 1984): comm "test_progs", pid 2451, jiffies 4295320596 hex dump (first 32 bytes): 7f 00 00 01 7f 00 00 01 d2 04 1b b7 04 d2 00 00 ................ 02 00 01 40 00 00 00 00 00 00 00 00 00 00 00 00 ...@............ backtrace (crc bdee079d): kmem_cache_alloc_noprof+0x557/0x660 sk_prot_alloc+0x69/0x240 sk_alloc+0x30/0x460 inet_create+0x2ce/0xf80 __sock_create+0x25b/0x5c0 __sys_socket+0x119/0x1d0 __x64_sys_socket+0x72/0xd0 do_syscall_64+0xa1/0x5f0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Instead of special-casing for refcounted sockets, reject unhashed UDP sockets during sockmap updates, as there is no benefit to supporting those. This effectively reverts the commit under Fixes, with two exceptions: 1. sock_map_sk_state_allowed() maintains a fall-through `return true`. 2. In the spirit of commit b8b8315e39ff ("bpf, sockmap: Remove unhash handler for BPF sockmap usage"), the proto::unhash BPF handler is not reintroduced. Historical note: this issue is related to commit 67312adc96b5 ("bpf: reject unhashed sockets in bpf_sk_assign").

Linux

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: printer: fix infinite loop in printer_read() printer_read() uses the same variable for the requested copy size and the number of bytes actually copied to user space. copy_to_user() returns the number of bytes not copied, so when it fails to copy anything, the computed copied length becomes zero. In that case len, buf, current_rx_bytes and current_rx_buf are left unchanged. If RX data is available and the user buffer remains unwritable, the read loop can repeat indefinitely. Track the copied length separately and return -EFAULT, or the number of bytes already copied, if an iteration makes no progress.

Linux

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_ncm: validate datagram bounds in ncm_unwrap_ntb() When unpacking host-supplied NTBs, ncm_unwrap_ntb() checks datagram length against frame_max but does not verify that the datagram fits within the declared block length. Additionally, when decoding multiple NTBs from a single socket buffer, subsequent block lengths are not checked against the actual remaining buffer data. With these checks missing, a malicious USB host can specify datagram offsets and lengths that point beyond the block, or supply secondary NTB headers declaring lengths larger than the buffer. skb_put_data() then copies adjacent kernel memory from skb_shared_info into the network skb. Fix this by verifying that sufficient buffer space remains for the NTB header before parsing, handling zero-length block declarations, ensuring that block lengths never exceed the remaining buffer space, and verifying that each datagram payload stays strictly within the block boundary.

Linux

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: uvc: clamp SEND_RESPONSE length to the response buffer uvc_send_response() builds the UVC control response from a user-supplied struct uvc_request_data: req->length = min_t(unsigned int, uvc->event_length, data->length); ... memcpy(req->buf, data->data, req->length); req->length is clamped to uvc->event_length, which is taken from the host control request wLength (up to UVC_MAX_REQUEST_SIZE, 64), and to data->length, which comes from the UVCIOC_SEND_RESPONSE ioctl and is only checked for being negative. The source buffer data->data is only 60 bytes, so a response with uvc->event_length and data->length both greater than 60 makes memcpy() read past the end of data->data. Clamp req->length to sizeof(data->data) as well.

Linux

In the Linux kernel, the following vulnerability has been resolved: USB: serial: io_edgeport: cap received transmit credits The interrupt-status packet reports transmit credits returned by the device. edge_interrupt_callback() adds the 16-bit value to txCredits without checking maxTxCredits. edge_write() uses txCredits minus the software FIFO count as the amount of data that fits. Since the FIFO is allocated with maxTxCredits bytes, txCredits exceeding maxTxCredits can cause OOB write in ring buffer. Cap accumulated credits at maxTxCredits. Conforming devices should never hit the cap.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k: hif_usb: don't dereference hif_dev after re-arming firmware request ath9k_hif_request_firmware() re-arms an asynchronous firmware load via request_firmware_nowait(), passing hif_dev as the completion context, and then still dereferences hif_dev: dev_info(&hif_dev->udev->dev, "ath9k_htc: Firmware %s requested\n", hif_dev->fw_name); The re-armed callback ath9k_hif_usb_firmware_cb() runs on the "events" workqueue and, when the firmware is missing, walks the retry chain into ath9k_hif_usb_firmware_fail() -> complete_all(&hif_dev->fw_done). That releases the wait_for_completion(&hif_dev->fw_done) in a concurrent ath9k_hif_usb_disconnect(), which then kfree()s hif_dev. The trailing dev_info() in the frame that re-armed the request can therefore read freed memory (hif_dev->udev, the first field of struct hif_device_usb): BUG: KASAN: slab-use-after-free in ath9k_hif_request_firmware Read of size 8 ... by task kworker/... ath9k_hif_request_firmware ath9k_hif_usb_firmware_cb drivers/net/wireless/ath/ath9k/hif_usb.c:1247 request_firmware_work_func Allocated by ...: ath9k_hif_usb_probe drivers/net/wireless/ath/ath9k/hif_usb.c Freed by ...: ath9k_hif_usb_disconnect -> kfree drivers/net/wireless/ath/ath9k/hif_usb.c The fw_done barrier only makes disconnect wait for the firmware chain to *terminate*; it does not protect the outer ath9k_hif_request_firmware() frame that re-armed the request and keeps touching hif_dev afterwards. Drop the post-request dev_info(): it is the only use of hif_dev after the async request is armed, and it is purely informational (the dev_err() on the failure path runs only when request_firmware_nowait() did not arm a callback, so hif_dev is still alive there). This was first reported by syzbot as a single, non-reproduced crash that was later auto-obsoleted, and was independently rediscovered by the reFuzz fuzzer, which produced a C reproducer (USB-gadget connect/disconnect of an ath9k_htc device whose firmware download fails). The vulnerable code is unchanged and still present in v7.1-rc6, where the slab-use-after-free reproduces under KASAN once the (sub-microsecond) race window is widened.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix NULL pointer dereference in ath11k_hal_srng_access_begin In ATH11K_QMI_EVENT_FW_READY, ATH11K_FLAG_REGISTERED is set unconditionally even when ath11k_core_qmi_firmware_ready() fails. This leaves the driver in an inconsistent state where initialization is considered complete although the firmware ready handling did not finish successfully. During the subsequent SSR, the driver enters the restart path based on this incorrect state and dereferences uninitialized srng members, resulting in a NULL pointer dereference. Call trace: ath11k_hal_srng_access_begin+0xc/0x60 [ath11k] (P) ath11k_ce_cleanup_pipes+0x17c/0x180 [ath11k] ath11k_core_restart+0x40/0x168 [ath11k] Fix this by: - skipping firmware_ready if ATH11K_FLAG_REGISTERED is already set - setting ATH11K_FLAG_REGISTERED only when firmware_ready succeeds - setting ATH11K_FLAG_QMI_FAIL and aborting the FW_READY handling on error Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.2.0.c2-00204-QCAMSLSWPLZ-1

Linux

In the Linux kernel, the following vulnerability has been resolved: hwmon: (corsair-psu) Stop device IO before calling hid_hw_stop hid_hw_stop() does not stop the device IO. This results in a race condition between hid_input_report() and the point immediately following the execution of hid_device_io_start() within corsairpsu_probe(). If the probe operation fails after "io start" has been initiated, this race condition will result in a uaf vulnerability [1]. CPU0 CPU1 ==== ==== corsairpsu_probe() hid_device_io_start() ... unlock driver_input_lock hid_hw_stop() kfree(hidraw) __hid_input_report() ... acquire driver_input_lock hid_report_raw_event() hidraw_report_event() ... access hidraw's list_lock // trigger uaf Consequently, when corsairpsu_probe() fails and hid_hw_stop() needs to be executed, the io_started flag is first cleared while holding the driver_input_lock to prevent potential race conditions involving input reports. [1] BUG: KASAN: slab-use-after-free in rt_spin_lock+0x83/0x400 kernel/locking/spinlock_rt.c:56 Call Trace: hidraw_report_event+0x5d/0x3a0 drivers/hid/hidraw.c:577 hid_report_raw_event+0x311/0x1730 drivers/hid/hid-core.c:2076 __hid_input_report drivers/hid/hid-core.c:2152 [inline] hid_input_report+0x44e/0x580 drivers/hid/hid-core.c:2174 hid_irq_in+0x47e/0x6d0 drivers/hid/usbhid/hid-core.c:286 __usb_hcd_giveback_urb+0x3b3/0x5e0 drivers/usb/core/hcd.c:1657 dummy_timer+0x8a9/0x47d0 drivers/usb/gadget/udc/dummy_hcd.c:2005 Allocated by task 10: hidraw_connect+0x57/0x430 drivers/hid/hidraw.c:606 hid_connect+0x5bf/0x19d0 drivers/hid/hid-core.c:2277 hid_hw_start+0xa8/0x120 drivers/hid/hid-core.c:2387 corsairpsu_probe+0xd9/0x3c0 drivers/hwmon/corsair-psu.c:782 Freed by task 10: hidraw_disconnect+0x4f/0x60 drivers/hid/hidraw.c:662 hid_disconnect drivers/hid/hid-core.c:2362 [inline] hid_hw_stop+0x101/0x1e0 drivers/hid/hid-core.c:2407 corsairpsu_probe+0x327/0x3c0 drivers/hwmon/corsair-psu.c:826 Fix the problem by calling hid_device_io_stop() before calling hid_hw_stop(). [groeck: Updated subject and description; call hid_device_io_stop() only if IO has been started]

Linux

In the Linux kernel, the following vulnerability has been resolved: hwmon: (corsair-cpro) Stop device IO before calling hid_hw_stop Calling hid_hw_stop() does not stop the device IO. This results in a race condition between hid_input_report() and the point immediately following the execution of hid_device_io_start() within the driver probe function. If the probe operation fails after "io start" has been initiated, this race condition will result in a UAF vulnerability. Fix the problem by calling hid_device_io_stop() before calling hid_hw_stop().

Linux

In the Linux kernel, the following vulnerability has been resolved: hwmon: (nzxt-smart2) Stop device IO before calling hid_hw_stop Calling hid_hw_stop() does not stop the device IO. This results in a race condition between hid_input_report() and the point immediately following the execution of hid_device_io_start() within the driver probe function. If the probe operation fails after "io start" has been initiated, this race condition will result in a UAF vulnerability. Fix the problem by calling hid_device_io_stop() before calling hid_hw_stop().

Linux

In the Linux kernel, the following vulnerability has been resolved: watchdog: pretimeout: Fix UAF in watchdog_unregister_governor() When a watchdog governor is unregistered, it updates existing watchdog devices that were using this governor by falling back to `default_gov`. If the governor being unregistered is currently set as `default_gov`, the `default_gov` is never cleared. This leads to 2 use-after-free issues: 1. New watchdog devices registered after this point will inherit the dangling `default_gov`. 2. Existing watchdog devices using the unregistered governor will have their `wdd->gov` reassigned to the dangling `default_gov`. Fix the UAF by clearing `default_gov` if it matches the governor being unregistered.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix potential buffer underflow in ath11k_hal_rx_msdu_list_get() When the first entry in msdu_details has a zero buffer address, the code accesses msdu_details[i - 1] with i == 0, causing a buffer underflow. Fix similarly to ath12k_wifi7_hal_rx_msdu_list_get() by adding a separate check for i == 0 before the main condition to prevent the out-of-bounds access. Found by Linux Verification Center (linuxtesting.org) with SVACE.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: bound memcpy length in cmd callback to prevent OOB read When the firmware sends a command response with a length mismatch, carl9170_cmd_callback() logs the mismatch and calls carl9170_restart() but then falls through to memcpy(ar->readbuf, buffer + 4, len - 4). Since len comes from the firmware and can exceed ar->readlen, this copies more data than the readbuf was allocated for. Bound the memcpy to min(len - 4, ar->readlen) so that the response is still completed -- avoiding repeated restarts from queued garbage -- while preventing an overread past the response buffer.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: fix OOB read from off-by-two in TX status handler The bounds check in carl9170_tx_process_status() uses `i > ((cmd->hdr.len / 2) + 1)` which is off by two, allowing 2 extra iterations past valid _tx_status entries when the firmware- controlled hdr.ext exceeds hdr.len/2. Fix by using the correct comparison `i >= (cmd->hdr.len / 2)`.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: carl9170: fix buffer overflow in rx_stream failover path The failover continuation in carl9170_rx_stream() copies the full tlen from the second USB transfer instead of capping at rx_failover_missing bytes. When both transfers are near maximum size, the total exceeds the 65535-byte failover SKB, triggering skb_over_panic. Limit the copy size to the missing byte count. [Fix checkpatch CHECK:PARENTHESIS_ALIGNMENT]

Linux

In the Linux kernel, the following vulnerability has been resolved: usb: atm: ueagle-atm: reject descriptors that confuse probe and disconnect uea_probe() distinguishes a pre-firmware device from a post-firmware one using the USB id (UEA_IS_PREFIRM()), and stores a different object as the interface data in each case: a 'struct completion' for a pre-firmware device (to be waited on in .disconnect()), or a 'struct usbatm_data' for a post-firmware one. uea_disconnect() instead tells the two apart by the number of interfaces of the active configuration (a pre-firmware device exposes a single interface, ADI930 has 2 and eagle has 3), and casts the interface data accordingly. Because the two handlers use different criteria, a crafted device that advertises a pre-firmware id together with a multi-interface descriptor (or a post-firmware id with a single interface) makes them disagree: the small 'struct completion' stored by uea_probe() is then passed to usbatm_usb_disconnect(), which casts it to 'struct usbatm_data' and takes instance->serialize, reading past the end of the allocation: BUG: KASAN: slab-out-of-bounds in __mutex_lock+0x152a/0x1b80 Read of size 8 at addr ffff8880470e2c60 by task kworker/1:2/982 ... __mutex_lock+0x152a/0x1b80 usbatm_usb_disconnect+0x70/0x820 uea_disconnect+0x133/0x2c0 usb_unbind_interface+0x1dd/0x9e0 ... which belongs to the cache kmalloc-96 of size 96 The buggy address is located 0 bytes to the right of allocated 96-byte region [ffff8880470e2c00, ffff8880470e2c60) Reject such inconsistent descriptors in uea_probe() so that both handlers always make the same pre/post-firmware decision.

Linux

In the Linux kernel, the following vulnerability has been resolved: bonding: fix devconf_all NULL dereference when IPv6 is disabled When booting with the 'ipv6.disable=1' parameter, the devconf_all is never initialized because inet6_init() exits before addrconf_init() is called which initializes it. bond_send_validate(), however, will still call bond_ns_send_all() even ipv6 is indeed disabled. It will lead to NULL derefence of net->ipv6.devconf_all in ip6_pol_route(). BUG: kernel NULL pointer dereference, address: 000000000000000c [...] Workqueue: bond0 bond_arp_monitor [bonding] RIP: 0010:ip6_pol_route+0x69/0x480 [...] Call Trace: <TASK> ? srso_return_thunk+0x5/0x5f ? __pfx_ip6_pol_route_output+0x10/0x10 fib6_rule_lookup+0xfe/0x260 ? wakeup_preempt+0x8a/0x90 ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? sched_balance_rq+0x369/0x810 ip6_route_output_flags+0xd7/0x170 bond_ns_send_all+0xde/0x280 [bonding] bond_ab_arp_probe+0x296/0x320 [bonding] ? srso_return_thunk+0x5/0x5f bond_activebackup_arp_mon+0xb4/0x2c0 [bonding] process_one_work+0x196/0x370 worker_thread+0x1af/0x320 ? srso_return_thunk+0x5/0x5f ? __pfx_worker_thread+0x10/0x10 kthread+0xe3/0x120 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x199/0x260 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Fix this by adding ipv6_mod_enabled() condition check in the caller.

Linux

In the Linux kernel, the following vulnerability has been resolved: dpaa2-switch: put MAC endpoint device on disconnect fsl_mc_get_endpoint() returns the MAC endpoint device with a reference taken through device_find_child(). The switch port connect path stores that device in mac->mc_dev and keeps it for the lifetime of the connected MAC object. However, the disconnect path only closes the MAC and frees the dpaa2_mac object. It does not drop the endpoint device reference stored in mac->mc_dev, so every successful connect leaks that device reference when the MAC is later disconnected. Drop the endpoint device reference before freeing the dpaa2_mac object.

Linux

In the Linux kernel, the following vulnerability has been resolved: dpaa2-eth: put MAC endpoint device on disconnect fsl_mc_get_endpoint() returns the MAC endpoint device with a reference taken through device_find_child(). The Ethernet connect path stores that device in mac->mc_dev and keeps it for the lifetime of the connected MAC object. However, the disconnect path only disconnects and closes the MAC before freeing the dpaa2_mac object. It does not drop the endpoint device reference stored in mac->mc_dev, so every successful connect leaks that device reference when the MAC is later disconnected. Drop the endpoint device reference after closing the MAC and before freeing the dpaa2_mac object.

Linux

In the Linux kernel, the following vulnerability has been resolved: nfp: Check resource mutex allocation nfp_cpp_resource_find() allocates a CPP mutex handle for the matching resource-table entry and then reports success. nfp_resource_try_acquire() immediately passes that handle to nfp_cpp_mutex_trylock(). However, nfp_cpp_mutex_alloc() returns NULL on failure. If that happens for a matching table entry, the resource lookup still returns success and the following trylock dereferences a NULL mutex pointer while opening the resource. nfp_resource_acquire() already treats failure to allocate the table mutex as -ENOMEM. Do the same for the resource mutex and fail the lookup before publishing the rest of the resource handle. This issue was found by a static analysis checker and confirmed by manual source review.

Linux

In the Linux kernel, the following vulnerability has been resolved: wan: wanxl: Only reset hardware after BAR mapping wanxl_pci_init_one() stores the freshly allocated card in driver data before the PLX BAR is mapped. Several early probe failures then unwind through wanxl_pci_remove_one(), including failure to allocate the coherent status area or to restore the DMA mask. wanxl_pci_remove_one() unconditionally calls wanxl_reset(), and wanxl_reset() dereferences card->plx. On those early failures card->plx is still NULL, so the error path can dereference a NULL MMIO pointer. Only issue the hardware reset once the BAR mapping exists. The remaining cleanup in wanxl_pci_remove_one() already checks whether later resources were allocated. This issue was found by a static analysis checker and confirmed by manual source review.

Linux

In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Bound the early ACPI HID map The ivrs_acpihid command-line parser appends entries to a fixed four-element early_acpihid_map array. Unlike the sibling IOAPIC and HPET parsers, it does not reject a fifth entry before incrementing the map size. Check the capacity at the common found label before parsing the HID and UID or writing the entry.

Linux

In the Linux kernel, the following vulnerability has been resolved: iommu/intel: Fix out-of-bounds memset in dmar_latency_disable() dmar_latency_disable() intends to zero out only the single latency_statistic entry for the given type, but the memset size was computed as sizeof(*lstat) * DMAR_LATENCY_NUM, which clears the entire array starting from &lstat[type]. When type > 0, this writes beyond the end of the allocated array, corrupting adjacent memory. Fix by using sizeof(*lstat) to clear only the target entry.

Linux

In the Linux kernel, the following vulnerability has been resolved: rds: Fix inet6_addr_lst NULL dereference when IPv6 is disabled When booting with the 'ipv6.disable=1' parameter, inet6_addr_lst is never initialized because inet6_init() exits before addrconf_init() is called to initialize it. An attempt to bind an RDS socket to an ipv6 address results in a crash in __ipv6_chk_addr_and_flags() KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f] RIP: 0010:__ipv6_chk_addr_and_flags+0x1df/0x7e0 Call Trace: <TASK> ipv6_chk_addr+0x3b/0x50 rds_tcp_laddr_check+0x155/0x3b0 [rds_tcp] rds_trans_get_preferred+0x15d/0x2d0 [rds] ? trace_hardirqs_on+0x2d/0x110 rds_bind+0x1433/0x1d60 [rds] ? rds_remove_bound+0xd50/0xd50 [rds] ? aa_af_perm+0x250/0x250 ? __might_fault+0xde/0x190 ? __sys_bind+0x1dc/0x210 __sys_bind+0x1dc/0x210 ? __ia32_sys_socketpair+0x100/0x100 ? restore_fpregs_from_fpstate+0x53/0x100 __x64_sys_bind+0x73/0xb0 ? syscall_enter_from_user_mode+0x1c/0x50 do_syscall_64+0x34/0x80 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 RIP: 0033:0x7f47f8269ea9 </TASK> The following code reproduces the issue: struct sockaddr_in6 addr; s = socket(PF_RDS, SOCK_SEQPACKET, 0); memset(&addr, 0, sizeof(addr)); inet_pton(AF_INET6, ADDRESS, &addr.sin6_addr); addr.sin6_family = AF_INET6; addr.sin6_port = htons(PORT); bind(s, &addr, sizeof(addr)); Found by InfoTeCS on behalf of Linux Verification Center (linuxtesting.org) with Syzkaller.

Linux

In the Linux kernel, the following vulnerability has been resolved: tipc: fix infinite loop in __tipc_nl_compat_dumpit cmd->dumpit callback can return a negative errno, causing an infinite loop due to the while(len) condition. As the loop never terminates, genl_mutex is never released, and other tasks waiting on it starve in D state. Check dumpit's return value, propagate it and jump to err_out on error.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7915: guard HE capability lookups mt7915_mcu_bss_he_tlv() and mt7915_mcu_sta_bfer_tlv() both run after checking HE support, then dereference the HE PHY capability returned by mt76_connac_get_he_phy_cap(). That helper can return NULL when no capability entry matches the vif type. Fetch the capability before appending the TLV and skip the HE-specific setup when no matching capability is available.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: connac: fix possible NULL-pointer deref in mt76_connac_mcu_uni_bss_he_tlv() mt76_connac_get_he_phy_cap routine can theoretically return NULL so check cap pointer before dereferencing it.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: fix 802.1X-SHA256 call trace warning Based on wpa_auth as 1x_256 mode, need to set up "use_fwsup" with BRCMF_PROFILE_FWSUP_1X. Or it will happen trace warning when call brcmf_cfg80211_set_pmk(). [ 4481.831101] ------------[ cut here ]------------ [ 4481.831102] WARNING: CPU: 1 PID: 2997 at drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:7242 brcmf_cfg80211_set_pmk+0x77/0xd0 [brcmfmac] [...] [ 4481.831202] Call Trace: [ 4481.831204]  <TASK> [ 4481.831205]  nl80211_set_pmk+0x183/0x250 [cfg80211] [ 4481.831233]  genl_family_rcv_msg_doit+0xea/0x150 [ 4481.831237]  genl_rcv_msg+0x104/0x240 [ 4481.831239]  ? cfg80211_probe_status+0x2c0/0x2c0 [cfg80211] [ 4481.831257]  ? genl_family_rcv_msg_doit+0x150/0x150 [ 4481.831259]  netlink_rcv_skb+0x4e/0x100 [ 4481.831261]  genl_rcv+0x24/0x40 [ 4481.831262]  netlink_unicast+0x236/0x380 [ 4481.831264]  netlink_sendmsg+0x250/0x4b0 [ 4481.831266]  sock_sendmsg+0x5c/0x70 [ 4481.831269]  ____sys_sendmsg+0x236/0x2b0 [ 4481.831271]  ? copy_msghdr_from_user+0x6d/0xa0 [ 4481.831272]  ___sys_sendmsg+0x86/0xd0 [ 4481.831274]  ? avc_has_perm+0x8c/0x1a0 [ 4481.831276]  ? preempt_count_add+0x6a/0xa0 [ 4481.831279]  ? sock_has_perm+0x82/0xa0 [ 4481.831280]  __sys_sendmsg+0x57/0xa0 [ 4481.831282]  do_syscall_64+0x38/0x90 [ 4481.831284]  entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 4481.831286] RIP: 0033:0x7fd270d369b4

Linux

In the Linux kernel, the following vulnerability has been resolved: net: hsr: fix memory leak on slave unregistration by removing synced VLANs When an HSR master device is brought UP, it auto-adds VLAN 0 via vlan_vid0_add(), which propagates VID 0 to its slave devices (slave A and B). If a slave device is later unregistered while HSR is active (e.g., during netns cleanup or interface destruction), hsr_del_port() is called to detach the slave port from the HSR master. However, hsr_del_port() currently does not delete the VLAN IDs that were synced to the slave device by HSR. As a result, the slave device retains a refcount on VID 0 (and any other synced VLANs). When the slave device is destroyed, its vlan_info / vlan_vid_info structure remains allocated, leading to a memory leak. Fix this by calling vlan_vids_del_by_dev(port->dev, master->dev) in hsr_del_port() before unlinking slave A or slave B ports, matching the propagation logic in hsr_ndo_vlan_rx_add_vid() / hsr_ndo_vlan_rx_kill_vid() and the cleanup behavior in bonding and team drivers.

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gem: Add missing nospec on parallel submit slot Add missing Spectre mitigation for userspace controlled parallel submission slot. Discovered using AI-assisted static analysis confirmed by Intel Product Security. (cherry picked from commit 15b9353deff3cf72331c387780de3cf9c316b643)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Check bounds in allocate_event_notification_slot The valid event ids go from 0 to KFD_SIGNAL_EVENT_LIMIT allocate_event_notification_slot has an option to specify an event id to allocate at, used by CRIU. We weren't checking the bounds on that value. Check them. v2: Lower bounds check is unecessary because of idr_alloc already rejecting negative numbers. Upper bounds check should be KFD_SIGNAL_EVENT_LIMIT since the signal mode mappings might not yet exist (cherry picked from commit 6853f1f6cbbeb3f53ebbbd7286536aeb2c5d5f50)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/sdma6.0: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit c17a508a7d652da3728f8bbc481bfffe96d65a87)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/sdma5.2: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit ae658afc7f47f6147371ec42cc6b1a793dfdb5af)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/sdma5.0: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit 8d144a0eb09537055841af48c9e7c2d4cd48e84d)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/i915: Return NULL on error in active_instance Avoid returning &node->base when node is NULL due to OOM during GFP_ATOMIC allocation. Discovered using AI-assisted static analysis confirmed by Intel Product Security. (cherry picked from commit 6029bc064f0b1bac184203a50fbaaf070fa18832)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/gfx11: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit daa62107452d2451787c4248ca38fa2d1a0cbefd)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gem: Do not leak siblings[] on proto context error After a successful BALANCE/PARALLEL_SUBMIT extension on context creation, error during processing of next user extension leaks the siblings[] array. Fix that. Discovered using AI-assisted static analysis confirmed by Intel Product Security. (cherry picked from commit aa65e0a4b51b3b54b53e4142aaa2d997aa1061ff)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gem: Fix NULL deref in I915_CONTEXT_PARAM_SSEU Setting context engine slot N into I915_ENGINE_CLASS_INVALID / I915_ENGINE_CLASS_INVALID_NONE and attempting to apply I915_CONTEXT_PARAM_SSEU to the same slot N will deref NULL. Fix that. Discovered using AI-assisted static analysis confirmed by Intel Product Security. (cherry picked from commit 36eda5b5c2d40da41cc0a5403c26986237cf9e87)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix bo->pin leaking in amdgpu_bo_create_reserved amdgpu_bo_create_reserved() only allocates a new BO when *bo_ptr (struct amdgpu_bo **bo_ptr as input parameter) is NULL, it simply skips creation when *bo_ptr is non-NULL. But it unconditionally reserves, pins, gart allocates and maps the BO afterwards. When the same non-NULL BO pointer is passed in again, for example firmware buffers that live in adev and are re-loaded on every resume / cp_resume / start under AMDGPU_FW_LOAD_DIRECT, amdgpu_bo_pin() just increases pin_count unconditionally, however the matching teardown only unpins once, so pin_count never drops to zero, so TTM is not able to move, swap or evict a BO, causing BO leaks. This commit fixes this issue by only pinning the bo once at creation, and repeated calls no longer take additional pin references. (cherry picked from commit 3ddc0ae76202c447b6aec61e907b852bc94671cf)

Linux

In the Linux kernel, the following vulnerability has been resolved: media: airspy: Return queued buffers on start_streaming() failure The vb2 framework hands buffers to the driver via buf_queue() before calling start_streaming(). If start_streaming() returns an error without first returning those buffers via vb2_buffer_done(), vb2_start_streaming() fires WARN_ON(owned_by_drv_count) and the queued buffers leak. airspy_start_streaming() returned -ENODEV early when the USB device had been disconnected (s->udev == NULL) without returning any buffers that buf_queue() had already accepted. Take v4l2_lock first and jump to the existing err_clear_bit label, which already drains s->queued_bufs via vb2_buffer_done(..., VB2_BUF_STATE_QUEUED) before unlocking. This mirrors the uvcvideo fix in commit 4cf3b6fd54eb ("media: uvcvideo: Return queued buffers on start_streaming() failure").

Linux

In the Linux kernel, the following vulnerability has been resolved: media: cx231xx: fix devres lifetime USB drivers bind to USB interfaces and any device managed resources should have their lifetime tied to the interface rather than parent USB device. This avoids issues like memory leaks when drivers are unbound without their devices being physically disconnected (e.g. on probe deferral or configuration changes). Fix the driver state lifetime so that it is released on driver unbind.

Linux

In the Linux kernel, the following vulnerability has been resolved: media: cx23885: add ioremap return check and cleanup Add a check for the return value of pci_ioremap_bar() in cx23885_dev_setup(). If ioremap for BAR0 fails, release the already allocated PCI memory region, decrement the device count, and return -ENODEV. This prevents a potential null pointer dereference and ensures proper cleanup on memory mapping failure.

Linux

In the Linux kernel, the following vulnerability has been resolved: media: meson: vdec: Fix memory leak in error path of vdec_open The vdec_open() function previously jumped directly to err_m2m_release when vdec_init_ctrls() failed, skipping release of the m2m context. This caused a resource leak. Fix it by introducing a proper err_m2m_ctx_release label that calls v4l2_m2m_ctx_release(sess->m2m_ctx) before releasing the m2m device. This was identified via kmemleak: unreferenced object 0xffff0000205d6878 (size 8): comm "v4l_id", pid 5289, jiffies 4294938580 hex dump (first 8 bytes): 40 d2 49 18 00 00 ff ff @.I..... backtrace (crc d3204599): kmemleak_alloc+0xc8/0xf0 __kvmalloc_node_noprof+0x60c/0x850 v4l2_ctrl_handler_init_class+0x1b4/0x2e8 [videodev] vdec_open+0x1f4/0x788 [meson_vdec] v4l2_open+0x144/0x460 [videodev] chrdev_open+0x1ac/0x500 do_dentry_open+0x3f0/0xfe8 vfs_open+0x68/0x320 do_open+0x2d8/0x9a8 path_openat+0x1d0/0x4f0 do_filp_open+0x190/0x380 do_sys_openat2+0xf8/0x1b0 __arm64_sys_openat+0x13c/0x1e8 invoke_syscall+0xdc/0x268 el0_svc_common.constprop.0+0x178/0x258 do_el0_svc+0x4c/0x70

Linux

In the Linux kernel, the following vulnerability has been resolved: media: pci: dm1105: Free allocated workqueue Destroy allocated workqueue in remove() callback to free its resources, thus fixing memory leak.

Linux

In the Linux kernel, the following vulnerability has been resolved: media: pwc: Drain fill_buf on start_streaming() failure pwc_isoc_init() submits its isochronous URBs with usb_submit_urb(.., GFP_KERNEL) in a loop. After the first URB is submitted, its completion handler pwc_isoc_handler() can run on another CPU before the loop finishes: start_streaming() pwc_isoc_init() usb_submit_urb(urbs[0], GFP_KERNEL) pwc_isoc_handler(urbs[0]) pdev->fill_buf = pwc_get_next_fill_buf(pdev) usb_submit_urb(urbs[i>0], ..) -> fails pwc_isoc_cleanup(pdev) /* kills URBs */ return ret; pwc_cleanup_queued_bufs(pdev, VB2_BUF_STATE_QUEUED) pwc_get_next_fill_buf() detaches a buffer from pdev->queued_bufs and stores it in pdev->fill_buf. The error path in start_streaming() only drains pdev->queued_bufs, so the buffer parked in pdev->fill_buf is leaked. vb2_start_streaming() then triggers WARN_ON(owned_by_drv_count). stop_streaming() already handles this since commit 80b0963e1698 ("[media] pwc: fix WARN_ON"), which added the fill_buf drain in the teardown path but not in the start_streaming() error path. Mirror that handling on failure so start_streaming() returns with no buffer owned by the driver. Issue identified by automated review of the INV-003 series at https://sashiko.dev/

Linux

In the Linux kernel, the following vulnerability has been resolved: media: radio-si476x: Unregister v4l2_device on probe failure si476x_radio_probe() registers radio->v4l2dev before allocating the V4L2 controls and before registering the video device. If any of those later steps fails, probe returns through the exit label after freeing only the control handler. A failed probe does not call si476x_radio_remove(), so the v4l2_device_unregister() there is not reached. This leaves the parent device reference taken by v4l2_device_register() behind on the error path. Unregister the V4L2 device in the probe error path after freeing the controls.

Linux

In the Linux kernel, the following vulnerability has been resolved: media: rtl2832: fix use-after-free in rtl2832_remove() cancel_delayed_work_sync() is called before i2c_mux_del_adapters() in rtl2832_remove(). While the cancel waits for any running instance of i2c_gate_work to finish, it does not prevent the timer from being rescheduled by a concurrent thread. During probe, the r820t_attach() call attempts I2C transfers through the mux adapter. These transfers go through i2c_mux_master_xfer(), which calls rtl2832_deselect() after the transfer completes, rescheduling i2c_gate_work via schedule_delayed_work(). If this transfer is still in flight when rtl2832_remove() runs, rtl2832_deselect() can reschedule i2c_gate_work after it has been cancelled, causing a use-after-free when kfree(dev) is called. Fix this by calling i2c_mux_del_adapters() before cancel_delayed_work_sync(). Once the mux adapter is unregistered, no new I2C transfers can go through it, so rtl2832_deselect() can no longer reschedule i2c_gate_work. The subsequent cancel_delayed_work_sync() is then guaranteed to be final.

Linux

In the Linux kernel, the following vulnerability has been resolved: media: saa7134: Fix a possible memory leak in saa7134_video_init1 In saa7134_video_init1(), the return value of the first saa7134_pgtable_alloc() is not checked. If it fails, the function continues as if successful, leaving the driver with an invalid page table. Additionally, if vb2_queue_init() for the VBI queue fails after the video queue page table has been allocated, the allocated memory is not freed before returning. The second saa7134_pgtable_alloc() also lacks a return value check. Errors occur during device probing before the device is fully registered, the normal cleanup path in saa7134_finidev() is not executed, leading to memory leaks and potential use of uninitialized DMA resources. Check the return value of both saa7134_pgtable_alloc() calls and propagate errors. On failure of any later step, free allocated page tables to avoid memory leaks. Ensure control handlers are also released on error to prevent further resource leakage. Found by code review.

Linux

In the Linux kernel, the following vulnerability has been resolved: media: ti: vpe: unwind v4l2 device registration on probe error If the vpe_top resource is missing, vpe_probe() returns -ENODEV after v4l2_device_register() has succeeded. Probe failures do not call the driver's remove callback, so the v4l2 device remains registered on that error path. Route that failure through the existing v4l2_device_unregister() unwind label, matching the other errors after v4l2_device_register().

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: fix NULL dereference when the AP has HT-cap but no HT-oper mwifiex_tdls_add_ht_oper() gates its follow-the-AP-bandwidth path on bss_desc->bcn_ht_cap being present, but then dereferences a different pointer, bss_desc->bcn_ht_oper: if (ISSUPP_CHANWIDTH40(priv->adapter->hw_dot_11n_dev_cap) && bss_desc->bcn_ht_cap && ISALLOWED_CHANWIDTH40(bss_desc->bcn_ht_oper->ht_param)) bcn_ht_cap and bcn_ht_oper are populated independently while parsing the associated AP's beacon in mwifiex_update_bss_desc_with_ie(): an AP that advertises an HT Capabilities element but no HT Operation element leaves bcn_ht_cap non-NULL and bcn_ht_oper NULL. Setting up a TDLS link to a peer while associated to such an AP then dereferences the NULL bcn_ht_oper and crashes the kernel. Every other bcn_ht_oper user in the driver NULL-checks it first. Guard on the pointer that is actually dereferenced. Found by 0sec automated security-research tooling (https://0sec.ai).

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7615: drop TXRX_NOTIFY on non-mmio buses PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7615_rx_check() and mt7615_queue_rx_skb() dispatch it to mt7615_mac_tx_free() on every bus. mt7615_mac_tx_free() cleans the DMA tx queues with mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the mmio queue ops implement that callback; on the mt7663 USB and SDIO buses it is NULL, so a TXRX_NOTIFY there calls a NULL pointer in the RX worker. Same defect as the mt7921 and mt7925 patches in this series. Drop the event on non-mmio buses via mt76_is_mmio(), as in commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for non-mmio devices").

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7921: drop TXRX_NOTIFY on non-mmio buses PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7921_rx_check() and mt7921_queue_rx_skb() dispatch it to mt7921_mac_tx_free() on every bus. mt7921_mac_tx_free() cleans the DMA tx queues with mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the mmio queue ops implement that callback; on USB and SDIO it is NULL, so a TXRX_NOTIFY there calls a NULL pointer in the RX worker: BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:0x0 Call Trace: mt7921_mac_tx_free+0x64/0x310 [mt7921_common] mt7921_rx_check+0x5f/0xf0 [mt7921_common] mt76u_rx_worker+0x1b9/0x620 [mt76_usb] Drop the event on non-mmio buses via mt76_is_mmio(), as in commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for non-mmio devices").

Linux

In the Linux kernel, the following vulnerability has been resolved: staging: rtl8723bs: fix OOB reads in rtw_get_wps_ie() rtw_get_wps_ie() iterates over IE data from network frames without validating that the IE header and payload fit within the remaining buffer before reading them. Specifically: - in_ie[cnt + 1] is read without checking cnt + 1 < in_len - memcmp(&in_ie[cnt + 2], ...) accesses cnt + 2 without bounds check - in_ie[cnt + 1] is used as length without verifying payload fits Add bounds checks at the top of the loop body to break early if fewer than 2 bytes remain for the IE header, or if the declared payload extends past the end of the buffer. Also require at least 4 bytes of payload before comparing the WPS OUI.

Linux

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: RFCOMM: Fix session UAF in set_termios rfcomm_tty_set_termios() tests dlc->session without rfcomm_mutex and later passes the pointer to rfcomm_send_rpn(). The latter dereferences both session->initiator and session->sock. Meanwhile, krfcommd can unlink the DLC and free the session while holding rfcomm_mutex. The race can proceed as follows: TTY ioctl task krfcommd -------------- -------- load dlc->session enter rfcomm_send_rpn() lock rfcomm_mutex clear dlc->session free session unlock rfcomm_mutex read session->initiator KASAN reported: BUG: KASAN: slab-use-after-free in rfcomm_send_rpn+0x297/0x2a0 Read of size 4 at addr ffff88810012a850 by task poc/92 Call Trace: rfcomm_send_rpn+0x297/0x2a0 rfcomm_tty_set_termios+0x50d/0x850 tty_set_termios+0x596/0x950 set_termios+0x46a/0x6e0 tty_mode_ioctl+0x152/0xbd0 tty_ioctl+0x915/0x1240 __x64_sys_ioctl+0x134/0x1c0 Allocated by task 92: rfcomm_session_add+0x9e/0x2e0 rfcomm_dlc_open+0x8b1/0xe00 rfcomm_dev_activate+0x85/0x1a0 rfcomm_tty_open+0x90/0x280 Freed by task 68: kfree+0x131/0x3c0 rfcomm_session_del+0x119/0x180 rfcomm_run+0x737/0x4710 Add rfcomm_dlc_send_rpn(), which holds rfcomm_mutex while it verifies that the DLC is still attached and sends the RPN frame. Have the TTY path use the helper and drop its unlocked session check. This keeps the session valid through both the frame construction and socket send.

Linux

In the Linux kernel, the following vulnerability has been resolved: exec: fix unsigned loop counter wrap in transfer_args_to_stack() The stop value is derived from bprm->p >> PAGE_SHIFT. The index variable is an unsigned long. If bprm->p drops below PAGE_SIZE and stop becomes zero the loop condition index >= stop is always true. After the index == 0 iteration the decrement wraps to ULONG_MAX and bprm->page[ULONG_MAX] reads sizeof(void *) bytes in front of the array. The pointer has wrapped to -1. That garbage pointer is then passed to kmap_local_page() and PAGE_SIZE bytes are copied from wherever that lands into the stack of the process being created. And the loop doesn't terminate either... Getting there only requires bprm->p < PAGE_SIZE. On !MMU bprm_set_stack_limit() and bprm_hit_stack_limit() are empty. So the only constraint on how far bprm->p is pushed down is valid_arg_len(), i.e. that each individual string still fits in what is left. bprm->p starts at PAGE_SIZE * MAX_ARG_PAGES - sizeof(void *) so a single argument or environment string of a little over 31 pages leaves it in the first page: Oops - load access fault [#1] CPU: 0 UID: 0 PID: 1 Comm: victim Not tainted 7.2.0-rc4 #1 epc : __memcpy+0xd4/0xf8 ra : transfer_args_to_stack+0xaa/0xae s4 : ffffffffffffffff s2 : 0000000000000000 a1 : ffffffdc98000000 a2 : 0000000000001000 status: 0000000a00001880 badaddr: ffffffdc98000000 cause: 0000000000000005 [<801a5324>] __memcpy+0xd4/0xf8 [<800d5f6a>] load_flat_binary+0x43a/0x65e [<800a2de4>] bprm_execve+0x1d4/0x316 [<800a351a>] do_execveat_common+0x12e/0x138 [<800a3d44>] __riscv_sys_execve+0x38/0x4e Kernel panic - not syncing: Fatal exception in interrupt This is an arcane bug but we should still fix it. Count down from MAX_ARG_PAGES so the loop ends when index reaches stop, stop == 0 included. The iterations performed are unchanged for every other value of stop. Only CONFIG_MMU=n builds are affected, transfer_args_to_stack() is used by binfmt_flat and binfmt_elf_fdpic on nommu only. The loop predates git history. commit 7e7ec6a93434 ("elf_fdpic_transfer_args_to_stack(): make it generic") only moved it from binfmt_elf_fdpic.c into fs/exec.c and narrowed the copy to the used part of the first page. The condition and the decrement are unchanged from 2.6.12-rc2.

Linux

In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: set have_execfd only once the interpreter is opened load_misc_binary() raises bprm->have_execfd as soon as it sees the 'O' (or 'C') flag. This happens well before it opens the interpreter. If that open fails the flag stays set on the bprm. binfmt_misc is at the head of the format list so an interpreter open failure that returns -ENOEXEC lets the search fall through to a later format. This means it runs the matched binary directly having never staged an interpreter. So bprm->executable is NULL while have_execfd falsely claims a descriptor is present. Consequently, begin_new_exec() dereferences the missing executable: would_dump(bprm, bprm->executable); and NULL derefs. Had it not, the hand-off later in the same function would have failed anyway. FD_ADD(0, bprm->executable) rejects a NULL file with -ENOMEM. Both sites are past the point of no return so the exec cannot be unwound either way. This can be reached by unprivileged users as binfmt_misc can be mounted in user namespaces. So a user can register an 'O' entry whose interpreter lives on a FUSE mount, have the FUSE server fail the open with -ENOEXEC and execute a native ELF file that matches the entry. have_execfd only means anything alongside the executable it describes which is not set until the interpreter has been opened and staged. So lets raise it there, next to execfd_creds, which is already set at that point. An open failure now leaves it clear, so the fallback format derives credentials from the binary and emits no AT_EXECFD, as it would for any native exec. The argv rewrite load_misc_binary() performs before the open is still not undone. This means the binary sees the interpreter path in argv[0] and its own path in argv[1] but that predates this change and only became observable once the exec stopped faulting.

Linux

In the Linux kernel, the following vulnerability has been resolved: cdrom: fix stack out-of-bounds read in CDROMVOLCTRL mmc_ioctl_cdrom_volume() first reads the audio control mode page into a 32-byte stack buffer with cgc->buflen set to 24. If the device reports a block descriptor, the function increases cgc->buflen to include that descriptor and reads the page again. For CDROMVOLCTRL, the function then builds a MODE SELECT parameter list by moving cgc->buffer forward by offset - 8 bytes. This drops the block descriptor from the outgoing payload and leaves a new 8-byte mode parameter header in front of the audio control page. However, cgc->buflen is left unchanged. With a standard 8-byte block descriptor, cgc->buffer points at buffer + 8 but cgc->buflen remains 32. cdrom_mode_select() therefore asks the low level packet path to write 32 bytes from that adjusted pointer, reading 8 bytes past the end of the 32-byte stack buffer. This is not hit by CDROMVOLREAD, and CDROMVOLCTRL only triggers it on drives that return a non-zero block descriptor length, which helps explain why it has gone unnoticed. The overread is also sent to the device as extra MODE SELECT payload, so it may not produce an obvious local failure. Reduce cgc->buflen by the same amount as the buffer pointer adjustment so the MODE SELECT transfer covers only the intended parameter list.

Linux

In the Linux kernel, the following vulnerability has been resolved: firmware: stratix10-svc: fix memory leaks and list corruption bugs Fix a memory leak when gen_pool_alloc() fails by freeing pmem on the error path. Switch pmem allocation from devm_kzalloc() to kzalloc() with explicit kfree() in the free path to match its list-managed lifetime. Remove the erroneous list_del(&svc_data_mem) which corrupted the list head on failed lookups.

Linux

In the Linux kernel, the following vulnerability has been resolved: comedi: comedi_parport: deal with premature interrupt Syzbot reported a general protection fault in `comedi_get_is_subdevice_running()`, which was called from the interrupt handler `parport_interrupt()` in the "comedi_parport" driver, but it does not currently have a C reproducer for the problem. It's probably due to a premature interrupt for one of two reasons: 1. The driver sets up the interrupt handler before the comedi subdevices used by the interrupt handler have been allocated, but does not disable the interrupt in the parallel port's CTRL register first. 2. The driver uses a user-supplied I/O port base address which Syzbot would have supplied, but it might not be backed by real parallel port hardware. Change the initialization order in the driver's comedi "attach" handler (`parport_attach()`) so that the hardware registers are initialized before the interrupt handler is requested. This should prevent premature interrupts occurring for real hardware. Also add a test to the interrupt handler to ensure the comedi device is fully attached and return early if it isn't.

Linux

In the Linux kernel, the following vulnerability has been resolved: intel_th: fix MSC output device reference leak intel_th_output_open() looks up the output device with bus_find_device_by_devt(), which returns the device with a reference that must be dropped after use. commit 95fc36a234da ("intel_th: fix device leak on output open()") attempted to drop the reference from intel_th_output_release(). However, a successful open replaces file->f_op with the output driver file operations before returning, so close runs the output driver release callback instead. For MSC outputs, close runs intel_th_msc_release(), which only removes the per-file iterator and does not drop the device reference taken by intel_th_output_open(). Consequently, every successful MSC output open leaks one device reference. Drop the device reference from intel_th_msc_release(), which is the release path actually used for MSC output files. Remove the now-unused intel_th_output_release() callback from intel_th_output_fops.

Linux

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix mmiotrace possible NULL dereferencing of hiter->dev If the mmio_pipe_open() fails to find a PCI device, the hiter->dev will be assigned to NULL. The mmiotrace read() function dereferences the hiter->dev if hiter exists. Change the test of the read to not only check hiter being NULL, but also the hiter->dev before dereferencing it.

Linux

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix resource leak on mmiotrace trace_pipe close The mmiotrace tracer was added May 12th 2008. At that time, resources created in pipe_open() could not be freed because there was not pipe_close function pointer of the tracer. The pipe_close function pointer was added in December 7th, 2009, but the mmiotrace tracer was not updated. mmio_pipe_open() allocates a header_iter and takes a pci_dev reference when trace_pipe is opened. mmio_close() frees them, but it was only wired to the tracer's .close callback. tracing_release_pipe() invokes .pipe_close, not .close, when the trace_pipe file is released. As a result, closing trace_pipe with the mmiotrace tracer active leaked the header_iter allocation and left a stale pci_dev reference. Set .pipe_close to mmio_close, matching how function_graph wires both callbacks to the same handler. Note, if the trace_pipe is read to completion, it will clean up the resources, but if one were to run: # head -n 1 /sys/kernel/tracing/trace_pipe VERSION 20070824 Over and over again, it would trigger a massive leak.

Linux

In the Linux kernel, the following vulnerability has been resolved: mm/damon/core: validate ranges in damon_set_regions() DAMON core logic assumes zero length regions don't exist. However, a few DAMON API callers including DAMON_SYSFS, DAMON_RECLAIM and DAMON_LRU_SORT allow users to set empty monitoring target regions. This could result in WARN_ONCE() on CONFIG_DAMON_DEBUG_SANITY enabled kernel, and divide-by-zero from damon_merge_two_regions(). For example, the WANR_ONCE() can be triggered like below. # grep DAMON_DEBUG_SANITY /boot/config-$(uname -r) # CONFIG_DAMON_DEBUG_SANITY=y # damo start # cd /sys/kernel/mm/damon/admin/kdamonds/0 # echo 0 > contexts/0/targets/0/regions/0/start # echo 0 > contexts/0/targets/0/regions/0/end # echo commit > state # dmesg [....] [ 73.705780] ------------[ cut here ]------------ [ 73.707552] start 0 >= end 0 [ 73.708452] WARNING: mm/damon/core.c:359 at damon_new_region+0x6e/0x80, CPU#1: kdamond.0/758 [...] All DAMON API callers eventually use damon_set_regions() to setup the regions. Add the validation logic in the function.

Linux

In the Linux kernel, the following vulnerability has been resolved: mm/damon/core: disallow overlapping input ranges for damon_set_regions() damon_set_regions() assumes the input ranges are sorted by the address and don't overlap each other. Hence the assumption was initially to be explicitly validated. But commit 97d482f4592f ("mm/damon/sysfs: reuse damon_set_regions() for regions setting") has mistakenly removed the validation. This can make DAMON behave in unexpected ways. At the best, the monitoring results snapshot will just look weird since there will be overlapping regions. DAMOS will also work weirdly, applying the same action multiple times for overlapping regions, and make DAMOS quota weird. More seriously, depending on the setup and regions updates sequence, negative size regions can be made. It will trigger WARN_ONCE() if the kernel is built with CONFIG_DAMON_DEBUG_SANITY=y. Depending on the monitoring results, the negative size region can further trigger division by zero in damon_merge_two_regions(). Note that some of the consequences including the WARN_ONCE() and the divide by zero depend on commits that were introduced after the root cause commit 97d482f4592f ("mm/damon/sysfs: reuse damon_set_regions() for regions setting"). Fix the problems by checking the assumption and returning an error if the input ranges don't meet the assumption. The issue was discovered [1] by Sashiko.

Linux

In the Linux kernel, the following vulnerability has been resolved: binfmt_elf_fdpic: only honour the first PT_INTERP The program header scan handles PT_INTERP from a switch nested in the scan loop, so its break leaves the switch and not the loop. A binary carrying more than one PT_INTERP runs the case again and overwrites both interpreter_name and interpreter. The previous name allocation leaks and so does the previous interpreter reference, along with the write denial open_exec() took on it. The denial is never released, so the file stays unwritable for as long as the system runs. An unprivileged caller reaches this with a crafted binary and repeats it at will. binfmt_elf stops at the first PT_INTERP. Do the same here. The flaw dates back to the driver's introduction in the pre-git history tree introduced in v2.6.11 by 91808d6ebe39 ("[PATCH] FRV: Add FDPIC ELF binary format driver").

Linux

In the Linux kernel, the following vulnerability has been resolved: net: hip04: fix RX buffer leak on build_skb failure When build_skb() fails in hip04_rx_poll(), the driver jumps to the refill path without releasing the current RX buffer and its DMA mapping. Installing a replacement buffer then overwrites the slot references and leaks both resources. Keep the current slot intact and return budget so NAPI retries the same buffer. Also free a newly allocated RX fragment when dma_map_single() fails. This issue was found by an in-house static analysis tool.

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/gfx10: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit ac6f00beb658239bced4aaed9efbb04a35348d48)

Linux

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/gfx9: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit b71604f8685b0eba07866f4e8dc30f93e1931054)

Linux

In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Bump asid_generation on CPU online to avoid ASID collision after hotplug If a vCPU stays scheduled out (or blocked) while the last pCPU it ran on goes through a hotplug cycle (online->offline->online), and the vCPU then resumes execution on the same pCPU, then it is possible for it to run with an ASID that has now been assigned to a different vCPU, resulting in stale TLB translations being used. svm_enable_virtualization_cpu() resets asid_generation to 1 and sets next_asid to max_asid + 1 on every CPU online event, including hotplug cycles. Because next_asid starts beyond the pool boundary, the first call to new_asid() after an online event always wraps the pool, incrementing asid_generation to 2 and assigning ASIDs starting from min_asid. Consider two vCPUs from different VMs, vCPU-A pinned to CPU-X holding asid_generation=2 and ASID=N from before the hotplug event: 1. CPU-X goes offline and back online: asid_generation resets to 1, next_asid = max_asid + 1. 2. One or more vCPUs migrate to CPU-X and call new_asid(), wrapping the pool and consuming ASIDs starting from min_asid. Eventually vCPU-B from a different VM is assigned asid_generation=2, ASID=N — the same ASID that vCPU-A held before the hotplug. 3. vCPU-A enters pre_svm_run() on CPU-X: current_vmcb->cpu is unchanged so the migration branch is skipped. Its saved asid_generation=2 matches sd->asid_generation=2, so the generation check silently passes and vCPU-A continues running with ASID=N — the same ASID just freshly assigned to vCPU-B. Both vCPUs from different VMs now run on CPU-X with the same ASID, causing them to share NPT TLB entries and producing stale translations. The collision manifests as a KVM internal error (Suberror: 1, emulation failure). The NPT page fault reports a faulting GPA far outside the VM's physical memory range — a sign of stale TLB translations being used. KVM falls back to instruction emulation, which fails on FPU/XSave instructions (XRSTOR, STMXCSR) that the emulator does not implement. Fix this by incrementing asid_generation instead of resetting it to 1 in svm_enable_virtualization_cpu(). On module load, asid_generation starts at 0 (memset) and the increment produces 1, identical to the old behaviour. On subsequent hotplug cycles the generation advances beyond any value a vCPU previously observed on this CPU, so the generation check in pre_svm_run() reliably forces new_asid() on every vCPU after every hotplug cycle.

Linux

In the Linux kernel, the following vulnerability has been resolved: xfrm: policy: preallocate inexact bins before xfrm_hash_rebuild reinsert xfrm_hash_rebuild()'s first loop preallocates the bins/chains the reinsert loop needs, so the reinsert (after hlist_del_rcu()) cannot allocate or fail. But its guard is inverted: it skips policies with prefixlen < threshold and preallocates for the rest. prefixlen < threshold is exactly when policy_hash_bysel() returns NULL and the reinsert takes the allocating xfrm_policy_inexact_insert() path. So the loop preallocates for the exact policies (which never allocate) and skips the inexact ones, whose bin/node is then allocated GFP_ATOMIC during reinsert. On failure the error path only WARN_ONCE()s and continues, leaving a poisoned bydst node; the next rebuild's hlist_del_rcu() dereferences LIST_POISON2 and takes a GPF. Reachable under memory pressure, deterministic via failslab. Invert the guard so preallocation covers exactly the reinserted policies; the reinsert then allocates nothing and cannot fail. Crash: Oops: general protection fault, probably for non-canonical address 0xfbd59c0000000024: 0000 [#1] SMP KASAN NOPTI KASAN: maybe wild-memory-access in range [0xdead...] ... Workqueue: events xfrm_hash_rebuild RIP: 0010:xfrm_hash_rebuild+0x5b3/0x1190 RAX: dead000000000122 (LIST_POISON2 + offset) ... Call Trace: hlist_del_rcu (include/linux/rculist.h:599) xfrm_hash_rebuild (net/xfrm/xfrm_policy.c:1365) process_one_work (kernel/workqueue.c:3322) worker_thread (kernel/workqueue.c:3486) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245) ... Kernel panic - not syncing: Fatal exception in interrupt

Linux

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: fix NVM tag length underflow in TLV parser In the TLV_TYPE_NVM branch of qca_tlv_check_data() the tag loop bound is "while (idx < length - sizeof(struct tlv_type_nvm))". "length" is a signed int from the firmware TLV header and sizeof(struct tlv_type_nvm) is a size_t (12), so "length" is converted to size_t and any firmware-supplied "length" < 12 makes the subtraction wrap to a huge value. The loop body then reads a 12-byte struct tlv_type_nvm past the end of the short vmalloc'd firmware buffer (and the EDL_TAG_ID_* handlers can write past it). Rewrite the bound as "idx + sizeof(struct tlv_type_nvm) <= length"; both operands are non-negative, so it no longer underflows and a "length" too small for one record correctly skips the loop. BUG: KASAN: vmalloc-out-of-bounds in qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421) Read of size 2 at addr ffffc900000e5004 by task kworker/u9:0/52 Workqueue: hci0 hci_power_on Call Trace: ... kasan_report (mm/kasan/report.c:595) qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421 drivers/bluetooth/btqca.c:617) qca_uart_setup (drivers/bluetooth/btqca.c:948) qca_setup (drivers/bluetooth/hci_qca.c:2029) hci_uart_setup (drivers/bluetooth/hci_ldisc.c:438) hci_dev_open_sync (net/bluetooth/hci_sync.c:5227) hci_power_on (net/bluetooth/hci_core.c:920) process_one_work (kernel/workqueue.c:3322) worker_thread (kernel/workqueue.c:3486) kthread (kernel/kthread.c:436) ret_from_fork (arch/x86/kernel/process.c:158) ret_from_fork_asm (arch/x86/entry/entry_64.S:245)

Linux

In the Linux kernel, the following vulnerability has been resolved: ipv4: fib: free fib_alias with kfree_rcu() on insert error path fib_table_insert() publishes new_fa into the leaf's fa_list with fib_insert_alias() before calling the fib entry notifiers. When a notifier fails, the error path removes new_fa with fib_remove_alias() (hlist_del_rcu) and frees it right away with kmem_cache_free(). fib_table_lookup() walks that list under rcu_read_lock() only, so a concurrent lookup that already reached new_fa keeps reading it after the free: BUG: KASAN: slab-use-after-free in fib_table_lookup (net/ipv4/fib_trie.c:1601) Read of size 1 at addr ffff88810676d4eb by task exploit/297 Call Trace: fib_table_lookup (net/ipv4/fib_trie.c:1601) ip_route_output_key_hash_rcu (net/ipv4/route.c:2814) ip_route_output_key_hash (net/ipv4/route.c:2705) __ip4_datagram_connect (net/ipv4/datagram.c:49) udp_connect (net/ipv4/udp.c:2144) __sys_connect (net/socket.c:2167) __x64_sys_connect (net/socket.c:2173) do_syscall_64 entry_SYSCALL_64_after_hwframe which belongs to the cache ip_fib_alias of size 56 Triggering the error path needs CAP_NET_ADMIN and a registered fib notifier that can reject a route; a netdevsim device whose IPv4 FIB resource is exhausted is enough. Free new_fa with alias_free_mem_rcu(), as fib_table_delete() already does for a fib_alias removed from the trie.

Linux

In the Linux kernel, the following vulnerability has been resolved: wifi: p54: validate RX frame length in p54_rx_eeprom_readback() p54_rx_eeprom_readback() copies the requested EEPROM slice out of a device-supplied readback frame without checking that the skb actually holds that many bytes. Commit da1b9a55ff11 ("wifi: p54: prevent buffer-overflow in p54_rx_eeprom_readback()") closed the destination overflow by copying a fixed priv->eeprom_slice_size (and rejecting a mismatched advertised len), but the source side is still unbounded: nothing verifies the frame is long enough to supply that many bytes. A malicious USB device can send a short frame whose advertised len matches priv->eeprom_slice_size while the payload is truncated. The equality check passes and memcpy() reads past the end of the skb, leaking adjacent heap: BUG: KASAN: slab-out-of-bounds in p54_rx (drivers/net/wireless/intersil/p54/txrx.c:507) Read of size 1016 at addr ffff88800f077114 by task swapper/0/0 Call Trace: <IRQ> ... __asan_memcpy (mm/kasan/shadow.c:105) p54_rx (drivers/net/wireless/intersil/p54/txrx.c:507) p54u_rx_cb (drivers/net/wireless/intersil/p54/p54usb.c:163) __usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1657) dummy_timer (drivers/usb/gadget/udc/dummy_hcd.c:2005) ... </IRQ> The buggy address belongs to the object at ffff88800f0770c0 which belongs to the cache skbuff_small_head of size 704 The buggy address is located 84 bytes inside of allocated 704-byte region [ffff88800f0770c0, ffff88800f077380) Check that the slice fits in the skb before copying.

Linux

In the Linux kernel, the following vulnerability has been resolved: mpls: fix NULL deref in mpls_valid_fib_dump_req() on CONFIG_INET=n On CONFIG_INET=n builds, mpls_valid_fib_dump_req() walks the parsed attribute table itself instead of calling ip_valid_fib_dump_req(). The RTA_OIF arm passes tb[RTA_OIF] to nla_get_u32() without checking it is present, so an RTM_GETROUTE dump for AF_MPLS with strict checking and no RTA_OIF hits a NULL dereference. RTM_GETROUTE is RTNL_KIND_GET, which rtnetlink_rcv_msg() permits without CAP_NET_ADMIN, so an unprivileged user can trigger it. Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] RIP: 0010:mpls_valid_fib_dump_req (net/mpls/af_mpls.c:2189) Call Trace: mpls_dump_routes (net/mpls/af_mpls.c:2236) netlink_dump (net/netlink/af_netlink.c:2331) __netlink_dump_start (net/netlink/af_netlink.c:2446) rtnetlink_rcv_msg (net/core/rtnetlink.c:7033) netlink_rcv_skb (net/netlink/af_netlink.c:2556) netlink_unicast (net/netlink/af_netlink.c:1345) netlink_sendmsg (net/netlink/af_netlink.c:1900) __sock_sendmsg (net/socket.c:790) ____sys_sendmsg (net/socket.c:2684) ___sys_sendmsg (net/socket.c:2738) __sys_sendmsg (net/socket.c:2770) do_syscall_64 (arch/x86/entry/syscall_64.c:94) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) Skip unset attributes, as ip_valid_fib_dump_req() does.

Linux

In the Linux kernel, the following vulnerability has been resolved: Input: ims-pcu - fix heap-buffer-overflow in ims_pcu_process_data() The `ims_pcu_process_data()` processes incoming URB data byte by byte. However, it fails to check if the `read_pos` index exceeds IMS_PCU_BUF_SIZE. If a malicious USB device sends a packet larger than IMS_PCU_BUF_SIZE, `read_pos` will increment indefinitely. Moreover, since `read_pos` is located immediately after `read_buf`, the attacker can overwrite `read_pos` itself to arbitrarily control the index. This manipulated `read_pos` is subsequently used in `ims_pcu_handle_response()` to copy data into `cmd_buf`, leading to a heap buffer overflow. Specifically, an attacker can overwrite the `cmd_done.wait.head` located at offset 136 relative to `cmd_buf` in the `ims_pcu_handle_response()`. Consequently, when the driver calls `complete(&pcu->cmd_done)`, it triggers a control flow hijack by using the manipulated pointer. Fix this by adding a bounds check for `read_pos` before writing to `read_buf`. If the packet is too long, discard it, log a warning, and reset the parser state. [dtor: factor out resetting packet state, reset checksum as well]

Linux

In the Linux kernel, the following vulnerability has been resolved: ipv6: ndisc: fix NULL deref in accept_untracked_na() accept_untracked_na() re-fetches the inet6_dev with __in6_dev_get(dev) and dereferences idev->cnf.accept_untracked_na without a NULL check, even though its only caller ndisc_recv_na() already fetched and NULL-checked idev for the same device. Both reads of dev->ip6_ptr run in the same RCU read-side critical section, but a concurrent addrconf_ifdown() can clear dev->ip6_ptr between them: lowering the MTU below IPV6_MIN_MTU calls addrconf_ifdown() without the synchronize_net() that orders the unregister path, so the re-fetch returns NULL and oopses: BUG: KASAN: null-ptr-deref in ndisc_recv_na (net/ipv6/ndisc.c:974) Read of size 4 at addr 0000000000000364 Call Trace: <IRQ> ndisc_recv_na (net/ipv6/ndisc.c:974) icmpv6_rcv (net/ipv6/icmp.c:1193) ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:479) ip6_input_finish (net/ipv6/ip6_input.c:534) ip6_input (net/ipv6/ip6_input.c:545) ip6_mc_input (net/ipv6/ip6_input.c:635) ipv6_rcv (net/ipv6/ip6_input.c:351) </IRQ> It is reachable by an unprivileged user via a network namespace. Pass the caller's already validated idev instead of re-fetching it; the idev stays alive for the whole RCU critical section, so it is safe even after dev->ip6_ptr has been cleared.

Linux

In the Linux kernel, the following vulnerability has been resolved: bpf: Support for hardening against JIT spraying The BPF JIT allocator packs many small programs into larger executable allocations and reuses space within those allocations as programs are loaded and freed. When fresh code is written into space that a previous program occupied, an indirect jump into the new program can reuse a branch prediction left behind by the old one. Flush the indirect branch predictors before reusing JIT memory so that indirect jumps into a newly written program don't reuse predictions from an old program that occupied the same space. Introduce bpf_arch_pred_flush_enabled static key and bpf_arch_pred_flush static call for flushing the branch predictors on JIT memory reuse. Architectures that need a flush, can update it to a predictor flush function. By default, its a NOP and does not emit any CALL. Allocations larger than a pack are not covered by this flush. That is safe because cBPF programs (the unprivileged attack surface) are bounded well below a pack size. Issue a warning if this assumption is ever violated while the flush is active.

Linux

In the Linux kernel, the following vulnerability has been resolved: x86/bugs: Enable IBPB flush on BPF JIT allocation Enable hardening against JIT spraying when Spectre-v2 mitigations are in use. Specifically, issue an IBPB flush on BPF JIT memory reuse. Skip enabling the IBPB flush if the BPF dispatcher is already using a retpoline sequence. This hardening applies only when BPF-JIT is in use. Guard the enabling under CONFIG_BPF_JIT so that bugs.c still builds with CONFIG_BPF_JIT=n.

Linux

In the Linux kernel, the following vulnerability has been resolved: binfmt_misc: don't let an 'F' entry pin its own instance An entry registered with 'F' opens its interpreter at registration time and holds that file until the entry is freed. Any entry nobody removes by hand only gets closed once the binfmt_misc superblock is shut down. If the interpreter lives on a mount that keeps that superblock alive the two pin each other: binfmt_misc sb -> inode -> entry -> interp_file -> vfsmount -> binfmt_misc sb TL;DR the file is never closed. Once the mount namespace is gone there is nothing left to unregister through either. There are two ways to trigger this bug: - Point the interpreter at the instance itself. Its files are regular files owned by the mounter and both bm_get_inode() and simple_fill_super() leave i_op at empty_iops. So notify_change() falls back to simple_setattr() and chmod +x works. We never set SB_I_NOEXEC and so open_exec() accepts it. - Use the instance as an overlayfs lower layer. The overlay superblock holds a clone_private_mount() of every layer until it is destroyed and that clone is in no namespace. So umount_tree() never reaches it. That's a DoS. And it isn't only the superblock that leaks. It pins the user namespace it was mounted in, so every iteration permanently eats one of the caller's user namespace charges. So let's just do the sane thing. SB_I_NOEXEC makes open_exec() fail on the instance's own files and s_stack_depth makes overlayfs reject the layer before it ever takes a clone. That also covers the ecryptfs and fuse passthrough variants. What 'F' promises is unchanged. The stable tag is narrower than the Fixes tags on purpose. Before sandboxed mounts this needed global root against the single instance everyone shares, and the change doesn't apply to those trees anyway. Note that SB_I_NODEV is implicitly raised for userns mounts but raise it explicitly here as well.