Jeudi 23 juillet 2026
84 CVE
-
CVE-2026-53331 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: slimbus: qcom-ngd-ctrl: Avoid ABBA on tx_lock/ctrl->lock During the SSR/PDR down notification the tx_lock is taken with the intent to provide synchronization with active DMA transfers. But during this period qcom_slim_ngd_down() is invoked, which ends up in slim_report_absent(), which takes the slim_controller lock. In multiple other codepaths these two locks are taken in the opposite order (i.e. slim_controller then tx_lock). The result is a lockdep splat, and a possible deadlock: rprocctl/449 is trying to acquire lock: ffff00009793e620 (&ctrl->lock){+.+.}-{4:4}, at: slim_report_absent (drivers/slimbus/core.c:322) slimbus but task is already holding lock: ffff00009793fb50 (&ctrl->tx_lock){+.+.}-{4:4}, at: qcom_slim_ngd_ssr_pdr_notify (drivers/slimbus/qcom-ngd-ctrl.c:1475) slim_qcom_ngd_ctrl which lock already depends on the new lock. Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&ctrl->tx_lock); lock(&ctrl->lock); lock(&ctrl->tx_lock); lock(&ctrl->lock); The assumption is that the comment refers to the desire to not call qcom_slim_ngd_exit_dma() while we have an ongoing DMA TX transaction. But any such transaction is initiated and completed within a single qcom_slim_ngd_xfer_msg(). Prior to calling qcom_slim_ngd_exit_dma() the slim_controller is torn down, all child devices are notified that the slimbus is gone and the child devices are removed. Stop taking the tx_lock in qcom_slim_ngd_ssr_pdr_notify() to avoid the deadlock.
-
CVE-2026-53333 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: mm/mincore: handle non-swap entries before !CONFIG_SWAP guard mincore_swap() also fields migration/hwpoison entries (and shmem swapin-error entries), which can exist on !CONFIG_SWAP builds when CONFIG_MIGRATION or CONFIG_MEMORY_FAILURE is enabled. The !IS_ENABLED(CONFIG_SWAP) guard ran before the non-swap-entry early return, so mincore_pte_range() can spuriously WARN and report these pages nonresident on !CONFIG_SWAP kernels. Move the guard below the non-swap-entry check so only true swap entries trip the WARN, and migration/hwpoison entries take the existing "uptodate / non-shmem" path.
-
CVE-2026-53334 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: mm/damon/reclaim: handle ctx allocation failure Patch series "mm/damon/{reclaim,lru_sort}: handle ctx allocation failures". DAMON_RECLAIM and DAMON_LRU_SORT could dereference NULL pointers if their damon_ctx object allocations fail. The bugs are expected to happen infrequently because the allocations are arguably too small to fail on common setups. But theoretically they are possible and the consequences are bad. Fix those. The issues were discovered [1] by Sashiko. This patch (of 2): DAMON_RECLAIM allocates the damon_ctx object for its kdamond in its init function. damon_reclaim_enabled_store() wrongly assumes the allocation will always succeed once tried. If the damon_ctx allocation was failed, therefore, code execution reaches to damon_commit_ctx() while 'ctx' is NULL. As a result, it dereferences the NULL 'ctx' pointer. Avoid the NULL dereference by returning -ENOMEM if 'ctx' is NULL.
-
CVE-2026-53335 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: mm/damon/lru_sort: handle ctx allocation failure DAMON_LRU_SORT allocates the damon_ctx object for its kdamond in its init function. damon_lru_sort_enabled_store() wrongly assumes the allocation will always succeed once tried. If the damon_ctx allocation was failed, therefore, code execution reaches to damon_commit_ctx() while 'ctx' is NULL. As a result, it dereferences the NULL 'ctx' pointer. Avoid the NULL dereference by returning -ENOMEM if 'ctx' is NULL.
-
CVE-2026-53336 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: nvmem: layouts: onie-tlv: fix hang on unknown types The EEPROM on my board has a vendor specific entry of type 0x41. When stumbling upon that, this driver hangs in an endless loop. Fix it by keep incrementing the offset on unknown entries, so the loop will eventually stop.
-
CVE-2026-53338 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: net: airoha: Add NULL check for of_reserved_mem_lookup() in airoha_qdma_init_hfwd_queues() of_reserved_mem_lookup() may return NULL if the reserved memory region referenced by the "memory-region" phandle is not found in the reserved memory table (e.g. due to a misconfigured DTS or a removed memory-region node). The current code dereferences the returned pointer without checking for NULL, leading to a kernel NULL pointer dereference at the following lines: dma_addr = rmem->base; // line 1156 num_desc = div_u64(rmem->size, buf_size); // line 1160 Add a NULL check after of_reserved_mem_lookup() and return -ENODEV if the lookup fails, which is consistent with the existing error handling for of_parse_phandle() failure in the same code block.
-
CVE-2026-53339 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: i2c: qcom-cci: Fix NULL pointer dereference in cci_remove() On all modern platforms Qualcomm CCI controller provides two I2C masters, and on particular boards only one I2C master may be initialized, and in such cases the device unbinding or driver removal causes a NULL pointer dereference, because cci_halt() is called for all two I2C masters, but a completion is initialized only for the single enabled master: % rmmod i2c-qcom-cci Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 <snip> Call trace: __wait_for_common+0x194/0x1a8 (P) wait_for_completion_timeout+0x20/0x2c cci_remove+0xc4/0x138 [i2c_qcom_cci] platform_remove+0x20/0x30 device_remove+0x4c/0x80 device_release_driver_internal+0x1c8/0x224 driver_detach+0x50/0x98 bus_remove_driver+0x6c/0xbc driver_unregister+0x30/0x60 platform_driver_unregister+0x14/0x20 qcom_cci_driver_exit+0x18/0x1008 [i2c_qcom_cci] ....
-
CVE-2026-53340 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: i2c: imx: fix clock and pinctrl state inconsistency in runtime PM In i2c_imx_runtime_suspend(), the clock is disabled before switching the pinctrl state to sleep. If pinctrl_pm_select_sleep_state() fails, the runtime suspend is aborted but the clock remains disabled, causing a system crash when the hardware is subsequently accessed. Fix this by switching the pinctrl state before disabling the clock so that a pinctrl failure leaves the clock enabled and the hardware accessible. In i2c_imx_runtime_resume(), restore the pinctrl state back to sleep if clk_enable() fails to keep the consistent.
-
CVE-2026-53342 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: arm64: mm: call pagetable dtor when freeing hot-removed page tables Since 5e8eb9aeeda3 ("arm64: mm: always call PTE/PMD ctor in __create_pgd_mapping()") page-table allocation on ARM64 always calls pagetable_{pte,pmd,pud,p4d}_ctor(). This sets the page_type to PGTY_table, increments NR_PAGETABLE and possible allocates a PTL. However the matching pagetable_dtor() calls were never added. With DEBUG_VM enabled on kernel versions prior to v6.17 without 2dfcd1608f3a9 ("mm/page_alloc: let page freeing clear any set page type") this leads to the following warning when freeing these pages due to page->page_type sharing page->_mapcount: BUG: Bad page state in process ... pfn:284fbb page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x284fbb flags: 0x17fffc000000000(node=0|zone=2|lastcpupid=0x1ffff) page_type: f2(table) page dumped because: nonzero mapcount Call trace: bad_page+0x13c/0x160 __free_frozen_pages+0x6cc/0x860 ___free_pages+0xf4/0x180 free_pages+0x54/0x80 free_hotplug_page_range.part.0+0x58/0x90 free_empty_tables+0x438/0x500 __remove_pgd_mapping.constprop.0+0x60/0xa8 arch_remove_memory+0x48/0x80 try_remove_memory+0x158/0x1d8 offline_and_remove_memory+0x138/0x180 It can also lead to leaking the ptl allocation if ALLOC_SPLIT_PTLOCKS is defined and incorrect NR_PAGETABLE stats. Fix this by calling pagetable_dtor() in free_hotplug_pgtable_page() prior to freeing the page to undo the effects of calling pagetable_*_ctor().
-
CVE-2026-53343 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: ARM: 9475/1: entry: use byte load for KASAN VMAP stack shadow Commit 44e9a3bb76e5 ("ARM: 9430/1: entry: Do a dummy read from VMAP shadow") added a dummy read from the KASAN VMAP stack shadow in __switch_to(). The read uses ldr, but the KASAN shadow address is byte-granular and is not guaranteed to be word aligned. ARMv5 faults unaligned word loads. With CONFIG_KASAN_VMALLOC and CONFIG_VMAP_STACK enabled, ARM926/VersatilePB crashes in __switch_to() with an alignment exception before reaching init. Use ldrb for the dummy shadow access. The code only needs to fault in the shadow mapping if the stack shadow is missing, so a byte load is sufficient and matches the granularity of KASAN shadow memory.
-
CVE-2026-53344 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: pinctrl: mcp23s08: Initialize mcp->dev and mcp->addr before regmap init Regmap initialization triggers regcache_maple_populate() which attempts SPI read to populate cache. SPI read requires mcp->dev and mcp->addr to be set, without them, NULL pointer dereference occurs during probe. Move initialization before mcp23s08_spi_regmap_init() call.
-
CVE-2026-53119 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: platform/wmi: use generic driver_override infrastructure When a driver is probed through __driver_attach(), the bus' match() callback is called without the device lock held, thus accessing the driver_override field without a lock, which can cause a UAF. Fix this by using the driver-core driver_override infrastructure taking care of proper locking internally. Note that calling match() from __driver_attach() without the device lock held is intentional. [1]
-
CVE-2026-53117 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: s390/cio: use generic driver_override infrastructure When a driver is probed through __driver_attach(), the bus' match() callback is called without the device lock held, thus accessing the driver_override field without a lock, which can cause a UAF. Fix this by using the driver-core driver_override infrastructure taking care of proper locking internally. Note that calling match() from __driver_attach() without the device lock held is intentional. [1]
-
CVE-2026-53116 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: s390/ap: use generic driver_override infrastructure When the AP masks are updated via apmask_store() or aqmask_store(), ap_bus_revise_bindings() is called after ap_attr_mutex has been released. This calls __ap_revise_reserved(), which accesses the driver_override field without holding any lock, racing against a concurrent driver_override_store() that may free the old string, resulting in a potential UAF. Fix this by using the driver-core driver_override infrastructure, which protects all accesses with an internal spinlock. Note that unlike most other buses, the AP bus does not check driver_override in its match() callback; the override is checked in ap_device_probe() and __ap_revise_reserved() instead. Also note that we do not enable the driver_override feature of struct bus_type, as AP - in contrast to most other buses - passes "" to sysfs_emit() when the driver_override pointer is NULL. Thus, printing "\n" instead of "(null)\n". Additionally, AP has a custom counter that is modified in the corresponding custom driver_override_store().
-
CVE-2026-53114 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: perf/amd/ibs: Avoid calling perf_allow_kernel() from the IBS NMI handler Calling perf_allow_kernel() from the NMI context is unsafe and could be fatal. Capture the permission at event-initialization time by storing it in event->hw.flags, and have the NMI handler rely on that cached flag instead of making the call directly.
-
CVE-2026-53112 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: wifi: rtlwifi: pci: fix possible use-after-free caused by unfinished irq_prepare_bcn_tasklet The irq_prepare_bcn_tasklet is initialized in rtl_pci_init() and scheduled when RTL_IMR_BCNINT interrupt is triggered by hardware. But it is never killed in rtl_pci_deinit(). When the rtlwifi card probe fails or is being detached, the ieee80211_hw is deallocated. However, irq_prepare_bcn_tasklet may still be running or pending, leading to use-after-free when the freed ieee80211_hw is accessed in _rtl_pci_prepare_bcn_tasklet(). Similar to irq_tasklet, add tasklet_kill() in rtl_pci_deinit() to ensure that irq_prepare_bcn_tasklet is properly terminated before the ieee80211_hw is released. The issue was identified through static analysis.
-
CVE-2026-53111 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: bpf: test_run: Fix the null pointer dereference issue in bpf_lwt_xmit_push_encap The bpf_lwt_xmit_push_encap helper needs to access skb_dst(skb)->dev to calculate the needed headroom: err = skb_cow_head(skb, len + LL_RESERVED_SPACE(skb_dst(skb)->dev)); But skb->_skb_refdst may not be initialized when the skb is set up by bpf_prog_test_run_skb function. Executing bpf_lwt_push_ip_encap function in this scenario will trigger null pointer dereference, causing a kernel crash as Yinhao reported: [ 105.186365] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 105.186382] #PF: supervisor read access in kernel mode [ 105.186388] #PF: error_code(0x0000) - not-present page [ 105.186393] PGD 121d3d067 P4D 121d3d067 PUD 106c83067 PMD 0 [ 105.186404] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 105.186412] CPU: 3 PID: 3250 Comm: poc Kdump: loaded Not tainted 6.19.0-rc5 #1 [ 105.186423] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 105.186427] RIP: 0010:bpf_lwt_push_ip_encap+0x1eb/0x520 [ 105.186443] Code: 0f 84 de 01 00 00 0f b7 4a 04 66 85 c9 0f 85 47 01 00 00 31 c0 5b 5d 41 5c 41 5d 41 5e c3 cc cc cc cc 48 8b 73 58 48 83 e6 fe <48> 8b 36 0f b7 be ec 00 00 00 0f b7 b6 e6 00 00 00 01 fe 83 e6 f0 [ 105.186449] RSP: 0018:ffffbb0e0387bc50 EFLAGS: 00010246 [ 105.186455] RAX: 000000000000004e RBX: ffff94c74e036500 RCX: ffff94c74874da00 [ 105.186460] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff94c74e036500 [ 105.186463] RBP: 0000000000000001 R08: 0000000000000002 R09: 0000000000000000 [ 105.186467] R10: ffffbb0e0387bd50 R11: 0000000000000000 R12: ffffbb0e0387bc98 [ 105.186471] R13: 0000000000000014 R14: 0000000000000000 R15: 0000000000000002 [ 105.186484] FS: 00007f166aa4d680(0000) GS:ffff94c8b7780000(0000) knlGS:0000000000000000 [ 105.186490] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 105.186494] CR2: 0000000000000000 CR3: 000000015eade001 CR4: 0000000000770ee0 [ 105.186499] PKRU: 55555554 [ 105.186502] Call Trace: [ 105.186507] <TASK> [ 105.186513] bpf_lwt_xmit_push_encap+0x2b/0x40 [ 105.186522] bpf_prog_a75eaad51e517912+0x41/0x49 [ 105.186536] ? kvm_clock_get_cycles+0x18/0x30 [ 105.186547] ? ktime_get+0x3c/0xa0 [ 105.186554] bpf_test_run+0x195/0x320 [ 105.186563] ? bpf_test_run+0x10f/0x320 [ 105.186579] bpf_prog_test_run_skb+0x2f5/0x4f0 [ 105.186590] __sys_bpf+0x69c/0xa40 [ 105.186603] __x64_sys_bpf+0x1e/0x30 [ 105.186611] do_syscall_64+0x59/0x110 [ 105.186620] entry_SYSCALL_64_after_hwframe+0x76/0xe0 [ 105.186649] RIP: 0033:0x7f166a97455d Temporarily add the setting of skb->_skb_refdst before bpf_test_run to resolve the issue.
-
CVE-2026-53107 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: wifi: libertas: don't kill URBs in interrupt context Serialization for the TX path was enforced by calling usb_kill_urb()/usb_kill_anchored_urbs(), to prevent transmission before a previous URB was completed. usb_tx_block() can be called from interrupt context (e.g. in the HCD giveback path), so we can't always use it to kill in-flight URBs. Prevent sleeping during interrupt context by checking the tx_submitted anchor for existing URBs. We now return -EBUSY, to indicate there's a pending request.
-
CVE-2026-53106 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: bpf: Do not allow deleting local storage in NMI Currently, local storage may deadlock when deferring freeing selem or local storage through kfree_rcu(), call_rcu() or call_rcu_tasks_trace() in NMI or reentrant. Since deleting selem in NMI is an unlikely use case, partially mitigate it by returning error when calling from bpf_xxx_storage_delete() helpers in NMI. Note that, it is still possible to deadlock through reentrant. A full mitigation requires returning error when irqs_disabled() is true, which, however is too heavy-handed for bpf_xxx_storage_delete(). The long-term solution requires _nolock versions of call_rcu. Another possible solution is to defer the free through irq_work [0], but it would grow the size of selem, which is non-ideal. The check is only needed in bpf_selem_unlink(), which is used by helpers and syscalls. bpf_selem_unlink_nofail() is fine as it is called during map and owner tear down that never run in NMI or reentrant. [0] https://lore.kernel.org/bpf/20260205190233.912-1-alexei.starovoitov@gmail.com/
-
CVE-2026-53121 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: amd-pstate: Fix memory leak in amd_pstate_epp_cpu_init() On failure to set the epp, the function amd_pstate_epp_cpu_init() returns with an error code without freeing the cpudata object that was allocated at the beginning of the function. Ensure that the cpudata object is freed before returning from the function. This memory leak was discovered by Claude Opus 4.6 with the aid of Chris Mason's AI review-prompts (https://github.com/masoncl/review-prompts/tree/main/kernel).
-
CVE-2026-53125 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: md: fix array_state=clear sysfs deadlock When "clear" is written to array_state, md_attr_store() breaks sysfs active protection so the array can delete itself from its own sysfs store method. However, md_attr_store() currently drops the mddev reference before calling sysfs_unbreak_active_protection(). Once do_md_stop(..., 0) has made the mddev eligible for delayed deletion, the temporary kobject reference taken by sysfs_break_active_protection() can become the last kobject reference protecting the md kobject. That allows sysfs_unbreak_active_protection() to drop the last kobject reference from the current sysfs writer context. kobject teardown then recurses into kernfs removal while the current sysfs node is still being unwound, and lockdep reports recursive locking on kn->active with kernfs_drain() in the call chain. Reproducer on an existing level: 1. Create an md0 linear array and activate it: mknod /dev/md0 b 9 0 echo none > /sys/block/md0/md/metadata_version echo linear > /sys/block/md0/md/level echo 1 > /sys/block/md0/md/raid_disks echo "$(cat /sys/class/block/sdb/dev)" > /sys/block/md0/md/new_dev echo "$(($(cat /sys/class/block/sdb/size) / 2))" > \ /sys/block/md0/md/dev-sdb/size echo 0 > /sys/block/md0/md/dev-sdb/slot echo active > /sys/block/md0/md/array_state 2. Wait briefly for the array to settle, then clear it: sleep 2 echo clear > /sys/block/md0/md/array_state The warning looks like: WARNING: possible recursive locking detected bash/588 is trying to acquire lock: (kn->active#65) at __kernfs_remove+0x157/0x1d0 but task is already holding lock: (kn->active#65) at sysfs_unbreak_active_protection+0x1f/0x40 ... Call Trace: kernfs_drain __kernfs_remove kernfs_remove_by_name_ns sysfs_remove_group sysfs_remove_groups __kobject_del kobject_put md_attr_store kernfs_fop_write_iter vfs_write ksys_write Restore active protection before mddev_put() so the extra sysfs kobject reference is dropped while the mddev is still held alive. The actual md kobject deletion is then deferred until after the sysfs write path has fully returned.
-
CVE-2026-53126 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: blk-cgroup: fix disk reference leak in blkcg_maybe_throttle_current() Add the missing put_disk() on the error path in blkcg_maybe_throttle_current(). When blkcg lookup, blkg lookup, or blkg_tryget() fails, the function jumps to the out label which only calls rcu_read_unlock() but does not release the disk reference acquired by blkcg_schedule_throttle() via get_device(). Since current->throttle_disk is already set to NULL before the lookup, blkcg_exit() cannot release this reference either, causing the disk to never be freed. Restore the reference release that was present as blk_put_queue() in the original code but was inadvertently dropped during the conversion from request_queue to gendisk.
-
CVE-2026-53127 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: block: fix zones_cond memory leak on zone revalidation error paths When blk_revalidate_disk_zones() fails after disk_revalidate_zone_resources() has allocated args.zones_cond, the memory is leaked because no error path frees it.
-
CVE-2026-53326 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: debugobjects: Don't call fill_pool() in early boot hardirq context When booting a debug PREEMPT_RT kernel on an ARM64 system, a "inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage" lockdep warning message was reported to the console. During early boot, interrupts are enabled before the scheduler is enabled. In this window (before SYSTEM_SCHEDULING is set) interrupts can fire and in the hard interrupt context handler attempt to fill the pool This can lead to a deadlock when the interrupt occurred when the interrupt hits a region which holds a lock that is required to be taken in the allocation path. Add a new can_fill_pool() helper and reorder the exception rule and forbid this scenario by excluding allocations from hard interrupt context.
-
CVE-2026-53327 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: debugobjects: Do not fill_pool() if pi_blocked_on On RT enabled kernels, fill_pool() ends up calling rtlock_lock(), which asserts if current::pi_blocked_on is set, because a task can obviously only block on one lock as otherwise the priority inheritenace chain gets corrupted. Prevent this by expanding the conditional to take current::pi_blocked_on into account.
-
CVE-2026-53328 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: sched_ext: Don't warn on NULL cgrp_moving_from in scx_cgroup_move_task() A WARN fires when systemd's user manager writes "+cpu +memory +pids" to its own subtree_control while a sched_ext scheduler is loaded: WARNING: at kernel/sched/ext.c:3227 scx_cgroup_move_task+0xa8/0xb0 scx_cgroup_move_task+0xa8/0xb0 sched_move_task+0x134/0x290 cpu_cgroup_attach+0x39/0x70 cgroup_migrate_execute+0x37d/0x450 cgroup_update_dfl_csses+0x1e3/0x270 cgroup_subtree_control_write+0x3e7/0x440 scx_cgroup_can_attach() arms cgrp_moving_from only when a task's cpu cgroup changes. It can still be NULL when scx_cgroup_move_task() runs, through this sequence: Step Result --------------------------------- ---------------------------------- 1. cpu enabled on cgroup G cpu css = A 2. cpu toggled off then on for G A killed, B created (same cgroup) 3. an exiting task keeps A alive migration skips it, A now stale 4. +memory migrates G stale A vs current B pulls cpu in 5. cpu attach runs for all tasks hits a live, cpu-unchanged task 6. scx_cgroup_move_task() on it cgrp_moving_from NULL -> WARN The mismatch is that scx_cgroup_can_attach() keys on cgroup identity while migration drives the move on css identity, so a NULL cgrp_moving_from here is a legitimate css-only migration, not a missing prep. The call is already gated on cgrp_moving_from, so just drop the warning. ops.cgroup_prep_move() and ops.cgroup_move() stay paired.
-
CVE-2026-53079 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: net_sched: fix skb memory leak in deferred qdisc drops When the network stack cleans up the deferred list via qdisc_run_end(), it operates on the root qdisc. If the root qdisc do not implement the TCQ_F_DEQUEUE_DROPS flag the packets queue to free are never freed and gets stranded on the child's local to_free list. Fix this by making qdisc_dequeue_drop() aware of the root qdisc. It fetches the root qdisc and check for the TCQ_F_DEQUEUE_DROPS flag. If the flag is present, the packet is appended directly to the root's to_free list. Otherwise, drop it directly as it was done before the optimization was implemented.
-
CVE-2026-53082 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: net: hamradio: 6pack: fix uninit-value in sixpack_receive_buf sixpack_receive_buf() does not properly skip bytes with TTY error flags. The while loop iterates through the flags buffer but never advances the data pointer (cp), and passes the original count (including error bytes) to sixpack_decode(). This causes sixpack_decode() to process bytes that should have been skipped due to TTY errors. The TTY layer does not guarantee that cp[i] holds a meaningful value when fp[i] is set, so passing those positions to sixpack_decode() results in KMSAN reporting an uninit-value read. Fix this by processing bytes one at a time, advancing cp on each iteration, and only passing valid (non-error) bytes to sixpack_decode(). This matches the pattern used by slip_receive_buf() and mkiss_receive_buf() for the same purpose.
-
CVE-2026-53083 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: bpf: Fix RCU stall in bpf_fd_array_map_clear() Add a missing cond_resched() in bpf_fd_array_map_clear() loop. For PROG_ARRAY maps with many entries this loop calls prog_array_map_poke_run() per entry which can be expensive, and without yielding this can cause RCU stalls under load: rcu: Stack dump where RCU GP kthread last ran: CPU: 0 UID: 0 PID: 30932 Comm: kworker/0:2 Not tainted 6.14.0-13195-g967e8def1100 #2 PREEMPT(undef) Workqueue: events prog_array_map_clear_deferred RIP: 0010:write_comp_data+0x38/0x90 kernel/kcov.c:246 Call Trace: <TASK> prog_array_map_poke_run+0x77/0x380 kernel/bpf/arraymap.c:1096 __fd_array_map_delete_elem+0x197/0x310 kernel/bpf/arraymap.c:925 bpf_fd_array_map_clear kernel/bpf/arraymap.c:1000 [inline] prog_array_map_clear_deferred+0x119/0x1b0 kernel/bpf/arraymap.c:1141 process_one_work+0x898/0x19d0 kernel/workqueue.c:3238 process_scheduled_works kernel/workqueue.c:3319 [inline] worker_thread+0x770/0x10b0 kernel/workqueue.c:3400 kthread+0x465/0x880 kernel/kthread.c:464 ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:153 ret_from_fork_asm+0x19/0x30 arch/x86/entry/entry_64.S:245 </TASK>
-
CVE-2026-53084 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: bpf: return VMA snapshot from task_vma iterator Holding the per-VMA lock across the BPF program body creates a lock ordering problem when helpers acquire locks that depend on mmap_lock: vm_lock -> i_rwsem -> mmap_lock -> vm_lock Snapshot the VMA under the per-VMA lock in _next() via memcpy(), then drop the lock before returning. The BPF program accesses only the snapshot. The verifier only trusts vm_mm and vm_file pointers (see BTF_TYPE_SAFE_TRUSTED_OR_NULL in verifier.c). vm_file is reference- counted with get_file() under the lock and released via fput() on the next iteration or in _destroy(). vm_mm is already correct because lock_vma_under_rcu() verifies vma->vm_mm == mm. All other pointers are left as-is by memcpy() since the verifier treats them as untrusted.
-
CVE-2026-53087 7.5 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: net: bcmgenet: fix leaking free_bds While reclaiming the tx queue we fast forward the write pointer to drop any data in flight. These dropped frames are not added back to the pool of free bds. We also need to tell the netdev that we are dropping said data.
-
CVE-2026-53093 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: Fix error pointer dereference The function brcmf_chip_add_core() can return an error pointer and is not checked. Add checks for error pointer. Detected by Smatch: drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1010 brcmf_chip_recognition() error: 'core' dereferencing possible ERR_PTR() drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1013 brcmf_chip_recognition() error: 'core' dereferencing possible ERR_PTR() drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1016 brcmf_chip_recognition() error: 'core' dereferencing possible ERR_PTR() drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1019 brcmf_chip_recognition() error: 'core' dereferencing possible ERR_PTR() drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1022 brcmf_chip_recognition() error: 'core' dereferencing possible ERR_PTR() [add missing wifi: prefix]
-
CVE-2026-53105 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7925: prevent NULL vif dereference in mt7925_mac_write_txwi Check for a NULL `vif` before accessing `ieee80211_vif_is_mld(vif)` to avoid a potential kernel panic in scenarios where `vif` might not be initialized.
-
CVE-2026-45782 8.9 Élevée
cloud-hypervisor
Cloud Hypervisor is a Virtual Machine Monitor for Cloud workloads. From version 21.0 to before version 51.2, a guest can cause a use-after-free in the cloud-hypervisor process by submitting two virtio-block descriptor chains that reuse the same head_index while asynchronous block I/O is enabled (e.g. io_uring, aio). When the kernel completes the duplicate operation before the original, the completion path frees a bounce buffer that the kernel is still actively reading from or writing to, corrupting the freed memory. This issue has been patched in versions 51.2 and 52.0.
-
CVE-2026-0466 5.5 Moyenne
AMD µProf · Amd uprof
Improper access control in AMD uProf may allow a local attacker with user privileges to write to the kernel-shared memory section, potentially resulting in crash or denial of service.
-
CVE-2026-49847 7.5 Élevée
signalwire freeswitch · Freeswitch freeswitch
FreeSWITCH is a Software Defined Telecom Stack enabling the digital transformation from proprietary telecom switches to a software implementation that runs on any commodity hardware. Prior to version 1.11.1, a single unauthenticated WebSocket frame containing a deeply nested JSON document crashes the FreeSWITCH process via stack overflow, terminating all calls and sessions on the host. The recursion drives the worker thread's stack pointer into the stack guard page, raising SIGSEGV from the kernel before any usable write primitive develops. This issue has been patched in version 1.11.1.
-
CVE-2026-48583 7.8 Élevée
Microsoft Windows 10 Version 1607 · Microsoft Windows 10 Version 1809 · Microsoft Windows 10 Version 21H2 · Microsoft Windows 10 Version 22H2
Use after free in Windows Kernel allows an authorized attacker to elevate privileges locally.
-
CVE-2026-45657 9.8 Critique
Microsoft Windows 11 Version 23H2 · Microsoft Windows 11 Version 24H2 · Microsoft Windows 11 Version 25H2 · Microsoft Windows 11 version 26H1
Use after free in Windows Kernel allows an unauthorized attacker to execute code over a network.
-
CVE-2026-45653 7.0 Élevée
Microsoft Windows 10 Version 1607 · Microsoft Windows 10 Version 1809 · Microsoft Windows 10 Version 21H2 · Microsoft Windows 10 Version 22H2
Heap-based buffer overflow in Windows Kernel allows an authorized attacker to elevate privileges locally.
-
CVE-2026-45600 7.8 Élevée
Microsoft Windows 11 Version 24H2 · Microsoft Windows 11 Version 25H2 · Microsoft Windows 11 version 26H1 · Microsoft Windows Server 2025
Access of resource using incompatible type ('type confusion') in Windows Kernel-Mode Drivers allows an authorized attacker to elevate privileges locally.
-
CVE-2026-45476 8.2 Élevée
Microsoft Linux kernel - Microsoft MANA Network Driver · Microsoft azure network adapter
Use after free in Linux MANA Driver allows an authorized attacker to elevate privileges locally.
-
CVE-2026-42984 7.0 Élevée
Microsoft Windows 10 Version 1809 · Microsoft Windows 10 Version 21H2 · Microsoft Windows 10 Version 22H2 · Microsoft Windows 11 Version 23H2
Use after free in Windows Kernel allows an authorized attacker to elevate privileges locally.
-
CVE-2026-42916 7.8 Élevée
Microsoft Windows 10 Version 1607 · Microsoft Windows 10 Version 1809 · Microsoft Windows 10 Version 21H2 · Microsoft Windows 10 Version 22H2
Integer overflow or wraparound in Windows NT OS Kernel allows an authorized attacker to elevate privileges locally.
-
CVE-2026-52907 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: media: rockchip: rkcif: fix off by one bugs Change these comparisons from > vs >= to avoid accessing one element beyond the end of the arrays. While at it, use ARRAY_SIZE instead of the _MAX enum values. [fix cosmetic issues]
-
CVE-2026-52906 7.7 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: 9p: fix access mode flags being ORed instead of replaced Since commit 1f3e4142c0eb ("9p: convert to the new mount API"), v9fs_apply_options() applies parsed mount flags with |= onto flags already set by v9fs_session_init(). For 9P2000.L, session_init sets V9FS_ACCESS_CLIENT as the default, so when the user mounts with "access=user", both bits end up set. Access mode checks compare against exact values, so having both bits set matches neither mode. This causes v9fs_fid_lookup() to fall through to the default switch case, using INVALID_UID (nobody/65534) instead of current_fsuid() for all fid lookups. Root is then unable to chown or perform other privileged operations. Fix by clearing the access mask before applying the user's choice.
-
CVE-2026-52905 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: mm/damon/core: disallow non-power of two min_region_sz on damon_start() Commit d8f867fa0825 ("mm/damon: add damon_ctx->min_sz_region") introduced a bug that allows unaligned DAMON region address ranges. Commit c80f46ac228b ("mm/damon/core: disallow non-power of two min_region_sz") fixed it, but only for damon_commit_ctx() use case. Still, DAMON sysfs interface can emit non-power of two min_region_sz via damon_start(). Fix the path by adding the is_power_of_2() check on damon_start(). The issue was discovered by sashiko [1].
-
CVE-2026-52904 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: drm/nouveau: fix nvkm_device leak on aperture removal failure When aperture_remove_conflicting_pci_devices() fails during probe, the error path returns directly without unwinding the nvkm_device that was just allocated by nvkm_device_pci_new(). This leaks both the device wrapper and the pci_enable_device() reference taken inside it. Jump to the existing fail_nvkm label so nvkm_device_del() runs and balances both. The leak was introduced when the intermediate nvkm_device_del() between detection and aperture removal was dropped in favor of creating the pci device once.
-
CVE-2026-46332 8.0 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: greybus: gb-beagleplay: bound bootloader receive buffering cc1352_bootloader_rx() appends each serdev chunk into the fixed rx_buffer before parsing bootloader packets. The helper can keep leftover bytes between callbacks and may receive multiple packets in one callback, so a single count value is not constrained by one packet length. Check that the incoming chunk fits in the remaining receive buffer space before memcpy(). If it does not, drop the staged data and consume the bytes instead of overflowing rx_buffer.
-
CVE-2026-46329 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: erofs: handle end of filesystem properly for file-backed mounts I/O requests beyond the end of the filesystem should be zeroed out, similar to loopback devices and that is what we expect.
-
CVE-2026-46328 7.3 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: apparmor: fix rlimit for posix cpu timers Posix cpu timers requires an additional step beyond setting the rlimit. Refactor the code so its clear when what code is setting the limit and conditionally update the posix cpu timers when appropriate.
-
CVE-2026-46326 8.4 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: iio: pressure: mprls0025pa: fix spi_transfer struct initialisation Make sure that the spi_transfer struct is zeroed out before use.
-
CVE-2026-46318 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: Revert "mm/hugetlbfs: update hugetlbfs to use mmap_prepare" This reverts commit ea52cb24cd3f ("mm/hugetlbfs: update hugetlbfs to use mmap_prepare") with conflict resolution to account for changes in commit ea52cb24cd3f ("mm/hugetlbfs: update hugetlbfs to use mmap_prepare"). The patch incorrectly handled hugetlb VMA lock allocation at the mmap_prepare stage, where a failed allocation occurring after mmap_prepare is called might result in the lock leaking. There is no risk of a merge causing a similar issues, as VMA_DONTEXPAND_BIT is set for hugetlb mappings. As a first step in addressing this issue, simply revert the change so we can rework how we do this having corrected the underlying issues. We maintain the VMA flags changes as best we can, accounting for the fact that we were working with a VMA descriptor previously and propagating like-for-like changes for this. Note that we invoke vma_set_flags() and do not call vma_start_write() as vm_flags_set() does. This is OK as it's being done in an .mmap hook where the VMA is not yet linked into the tree so nobody else can be accessing it.
-
CVE-2026-46315 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: io_uring/waitid: clear waitid info before copying it to userspace IORING_OP_WAITID stores its result fields in struct io_waitid::info and later copies them to userspace siginfo. The prep path initializes the request arguments, but it does not initialize info itself. If the wait operation completes without reporting a child event, the common wait code can return without writing wo_info. In that case io_waitid_finish() still copies iw->info to userspace, exposing stale bytes from the reused io_kiocb command storage. Clear the result storage during prep so the io_uring path matches the regular waitid syscall, which uses a zero-initialized struct waitid_info.
-
CVE-2026-27671 9.8 Critique
SAP_SE SAP NetWeaver AS ABAP and ABAP Platform
Due to improper RFC protocol validation in the SAP Kernel used by the Application Server ABAP of SAP NetWeaver and ABAP Platform, an unauthenticated attacker can send a crafted RFC request that exploits logical errors in memory management, leading to memory corruption. This could lead to a high impact on the confidentiality, integrity, and availability of the application.
-
CVE-2026-46310 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: media: renesas: vsp1: Fix NULL pointer deref on module unload When unloading the module on gen 4, we hit a NULL pointer dereference. This is caused by the cleanup code calling vsp1_drm_cleanup() where it should be calling vsp1_vspx_cleanup(). Fix this by checking the IP version and calling the drm or vspx function accordingly, the same way as the init code does.
-
CVE-2026-46309 7.0 Élevée
Linux · Red Hat Enterprise Linux 10 · Red Hat Enterprise Linux 6 · Red Hat Enterprise Linux 7
In the Linux kernel, the following vulnerability has been resolved: drm/xe/uapi: Reject coh_none PAT index for CPU cached memory in madvise Add validation in xe_vm_madvise_ioctl() to reject PAT indices with XE_COH_NONE coherency mode when applied to CPU cached memory. Using coh_none with CPU cached buffers is a security issue. When the kernel clears pages before reallocation, the clear operation stays in CPU cache (dirty). GPU with coh_none can bypass CPU caches and read stale sensitive data directly from DRAM, potentially leaking data from previously freed pages of other processes. This aligns with the existing validation in vm_bind path (xe_vm_bind_ioctl_validate_bo). v2(Matthew brost) - Add fixes - Move one debug print to better place v3(Matthew Auld) - Should be drm/xe/uapi - More Cc v4(Shuicheng Lin) - Fix kmem leak issues by the way v5 - Remove kmem leak because it has been merged by another patch v6 - Remove the fix which is not related to current fix v7 - No change v8 - Rebase v9 - Limit the restrictions to iGPU v10 - No change (cherry picked from commit 016ccdb674b8c899940b3944952c96a6a490d10a)
-
CVE-2026-46308 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: pmdomain: mediatek: fix use-after-free in scpsys_get_bus_protection_legacy() In scpsys_get_bus_protection_legacy(), of_find_node_with_property() returns a device node with its reference count incremented. The function then calls of_node_put(node) before checking whether syscon_regmap_lookup_by_phandle() returns an error. If an error occurs, dev_err_probe() dereferences the node pointer to print diagnostic information, but the node memory may have already been freed due to the earlier of_node_put(), leading to a use-after-free vulnerability. Fix this by moving the of_node_put() call after the error check, ensuring the node is still valid when accessed in the error path.
-
CVE-2026-46301 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: spi: topcliff-pch: fix use-after-free on unbind Give the driver a chance to flush its queue before releasing the DMA buffers on driver unbind
-
CVE-2026-46297 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: net: libwx: use request_irq for VF misc interrupt Currently, request_threaded_irq() is used with a primary handler but a NULL threaded handler, while also setting the IRQF_ONESHOT flag. This specific combination triggers a WARNING since the commit aef30c8d569c ("genirq: Warn about using IRQF_ONESHOT without a threaded handler"). WARNING: kernel/irq/manage.c:1502 at __setup_irq+0x4fa/0x760 Fix the issue by switching to request_irq(), which is the appropriate interface or a non-threaded interrupt handler, and removing the unnecessary IRQF_ONESHOT flag.
-
CVE-2026-46296 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: spi: s3c64xx: fix NULL-deref on driver unbind A change moving DMA channel allocation from probe() back to s3c64xx_spi_prepare_transfer() failed to remove the corresponding deallocation from remove(). Drop the bogus DMA channel release from remove() to avoid triggering a NULL-pointer dereference on driver unbind. This issue was flagged by Sashiko when reviewing a controller deregistration fix.
-
CVE-2026-46295 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Do IRR scan in __kvm_apic_update_irr even if PIR is empty Fall back to apic_find_highest_vector() when PID.ON is set but PIR turns out to be empty, to correctly report the highest pending interrupt from the existing IRR. In a nested VM stress test, the following WARNING fires in vmx_check_nested_events() when kvm_cpu_has_interrupt() reports a pending interrupt but the subsequent kvm_apic_has_interrupt() (which invokes vmx_sync_pir_to_irr() again) returns -1: WARNING: CPU: 99 PID: 57767 at arch/x86/kvm/vmx/nested.c:4449 vmx_check_nested_events+0x6bf/0x6e0 [kvm_intel] Call Trace: kvm_check_and_inject_events vcpu_enter_guest.constprop.0 vcpu_run kvm_arch_vcpu_ioctl_run kvm_vcpu_ioctl __x64_sys_ioctl do_syscall_64 entry_SYSCALL_64_after_hwframe The root cause is a race between vmx_sync_pir_to_irr() on the target vCPU and __vmx_deliver_posted_interrupt() on a sender vCPU. The sender performs two individually-atomic operations that are not a single transaction: 1. pi_test_and_set_pir(vector) -- sets the PIR bit 2. pi_test_and_set_on() -- sets PID.ON The following interleaving triggers the bug: Sender vCPU (IPI): Target vCPU (1st sync_pir_to_irr): B1: set PIR[vector] A1: pi_clear_on() A2: pi_harvest_pir() -> sees B1 bit A3: xchg() -> consumes bit, PIR=0 (1st sync returns correct max_irr) B2: set PID.ON = 1 Target vCPU (2nd sync_pir_to_irr): C1: pi_test_on() -> TRUE (from B2) C2: pi_clear_on() -> ON=0 C3: pi_harvest_pir() -> PIR empty C4: *max_irr = -1, early return IRR NOT SCANNED The interrupt is not lost (it resides in the IRR from the first sync and is recovered on the next vcpu_enter_guest() iteration), but the incorrect max_irr causes a spurious WARNING and a wasted L2 VM-Enter/VM-Exit cycle.
-
CVE-2026-46293 7.1 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: clk: microchip: mpfs-ccc: fix out of bounds access during output registration UBSAN reported an out of bounds access during registration of the last two outputs. This out of bounds access occurs because space is only allocated in the hws array for two PLLs and the four output dividers that each has, but the defined IDs contain two DLLS and their two outputs each, which are not supported by the driver. The ID order is PLLs -> DLLs -> PLL outputs -> DLL outputs. Decrement the PLL output IDs by two while adding them to the array to avoid the problem.
-
CVE-2026-46292 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: pmdomain: core: Fix detach procedure for virtual devices in genpd If a device is attached to a PM domain through genpd_dev_pm_attach_by_id(), genpd calls pm_runtime_enable() for the corresponding virtual device that it registers. While this avoids boilerplate code in drivers, there is no corresponding call to pm_runtime_disable() in genpd_dev_pm_detach(). This means these virtual devices are typically detached from its genpd, while runtime PM remains enabled for them, which is not how things are designed to work. In worst cases it may lead to critical errors, like a NULL pointer dereference bug in genpd_runtime_suspend(), which was recently reported. For another case, we may end up keeping an unnecessary vote for a performance state for the device. To fix these problems, let's add this missing call to pm_runtime_disable() in genpd_dev_pm_detach().
-
CVE-2026-46291 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: crypto: caam - guard HMAC key hex dumps in hash_digest_key Use print_hex_dump_devel() for dumping sensitive HMAC key bytes in hash_digest_key() to avoid leaking secrets at runtime when CONFIG_DYNAMIC_DEBUG is enabled.
-
CVE-2026-46290 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: x86/efi: Fix graceful fault handling after FPU softirq changes Since commit d02198550423 ("x86/fpu: Improve crypto performance by making kernel-mode FPU reliably usable in softirqs"), kernel_fpu_begin() calls fpregs_lock() which uses local_bh_disable() instead of the previous preempt_disable(). This sets SOFTIRQ_OFFSET in preempt_count during the entire EFI runtime service call, causing in_interrupt() to return true in normal task context. The graceful page fault handler efi_crash_gracefully_on_page_fault() uses in_interrupt() to bail out for faults in real interrupt context. With SOFTIRQ_OFFSET now set, the handler always bails out, leaving EFI firmware page faults unhandled. This escalates to die() which also sees in_interrupt() as true and calls panic("Fatal exception in interrupt"), resulting in a hard system freeze. On systems with buggy firmware that triggers page faults during EFI runtime calls (e.g., accessing unmapped memory in GetTime()), this causes an unrecoverable hang instead of the expected graceful EFI_ABORTED recovery. Fix by replacing in_interrupt() with !in_task(). This preserves the original intent of bailing for interrupts or NMI faults, while no longer falsely triggering from the FPU code path's local_bh_disable(). [ardb: Sashiko spotted that using 'in_hardirq() || in_nmi()' leaves a window where a softirq may be taken before fpregs_lock() is called, but after efi_rts_work.efi_rts_id has been assigned, and any page faults occurring in that window will then be misidentified as having been caused by the firmware. Instead, use !in_task(), which incorporates in_serving_softirq(). ]
-
CVE-2026-46289 9.8 Critique
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: lib/scatterlist: fix length calculations in extract_kvec_to_sg Patch series "Fix bugs in extract_iter_to_sg()", v3. Fix bugs in the kvec and user variants of extract_iter_to_sg. This series is growing due to useful remarks made by sashiko.dev. The main bugs are: - The length for an sglist entry when extracting from a kvec can exceed the number of bytes in the page. This is obviously not intended. - When extracting a user buffer the sglist is temporarily used as a scratch buffer for extracted page pointers. If the sglist already contains some elements this scratch buffer could overlap with existing entries in the sglist. The series adds test cases to the kunit_iov_iter test that demonstrate all of these bugs. Additionally, there is a memory leak fix for the test itself. The bugs were orignally introduced into kernel v6.3 where the function lived in fs/netfs/iterator.c. It was later moved to lib/scatterlist.c in v6.5. Thus the actual fix is only marked for backports to v6.5+. This patch (of 5): When extracting from a kvec to a scatterlist, do not cross page boundaries. The required length was already calculated but not used as intended. Adjust the copied length if the loop runs out of sglist entries without extracting everything. While there, return immediately from extract_iter_to_sg if there are no sglist entries at all. A subsequent commit will add kunit test cases that demonstrate that the patch is necessary.
-
CVE-2026-46288 8.4 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: of: unittest: fix use-after-free in of_unittest_changeset() The variable 'parent' is assigned the value of 'nchangeset' earlier in the function, meaning both point to the same struct device_node. The call to of_node_put(nchangeset) can decrement the reference count to zero and free the node if there are no other holders. After that, the code still uses 'parent' to check for the presence of a property and to read a string property, leading to a use-after-free. Fix this by moving the of_node_put() call after the last access to 'parent', avoiding the UAF.
-
CVE-2026-46286 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: leds: qcom-lpg: Check for array overflow when selecting the high resolution When selecting the high resolution values from the array, FIELD_GET() is used to pull from a 3 bit register, yet the array being indexed has only 5 values in it. Odds are the hardware is sane, but just to be safe, properly check before just overflowing and reading random data and then setting up chip values based on that.
-
CVE-2026-46285 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: mtd: docg3: fix use-after-free in docg3_release() In docg3_release(), the docg3 pointer is obtained from cascade->floors[0]->priv before the loop that calls doc_release_device() on each floor. doc_release_device() frees the docg3 struct via kfree(docg3) at line 1881. After the loop, docg3->cascade->bch dereferences the already-freed pointer. Fix this by accessing cascade->bch directly, which is equivalent since docg3->cascade points back to the same cascade struct, and is already available as a local variable. This also removes the now-unused docg3 local variable.
-
CVE-2026-46284 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: mm/hugetlb: fix early boot crash on parameters without '=' separator If hugepages, hugepagesz, or default_hugepagesz are specified on the kernel command line without the '=' separator, early parameter parsing passes NULL to hugetlb_add_param(), which dereferences it in strlen() and can crash the system during early boot. Reject NULL values in hugetlb_add_param() and return -EINVAL instead.
-
CVE-2026-46283 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: tpm: Use kfree_sensitive() to free auth session in tpm_dev_release() tpm_dev_release() uses plain kfree() to free chip->auth, which contains sensitive cryptographic material including HMAC session keys, nonces, and passphrase data (struct tpm2_auth). Every other code path that frees this structure uses kfree_sensitive() to zero the memory before releasing it: both tpm2_end_auth_session() and tpm_buf_check_hmac_response() do so. The tpm_dev_release() path is the only one that does not, leaving key material in freed slab memory until it is eventually overwritten. Use kfree_sensitive() for consistency with the rest of the driver and to ensure session keys are scrubbed during device teardown.
-
CVE-2026-46281 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: vmalloc: fix buffer overflow in vrealloc_node_align() Commit 4c5d3365882d ("mm/vmalloc: allow to set node and align in vrealloc") added the ability to force a new allocation if the current pointer is on the wrong NUMA node, or if an alignment constraint is not met, even if the user is shrinking the allocation. On this path (need_realloc), the code allocates a new object of 'size' bytes and then memcpy()s 'old_size' bytes into it. If the request is to shrink the object (size < old_size), this results in an out-of-bounds write on the new buffer. Fix this by bounding the copy length by the new allocation size.
-
CVE-2026-46278 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: drm/imagination: Fix segfault when updating ftrace mask Fix invalid data access by passing right data for debugfs entry. [ 171.549793] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 171.559248] Mem abort info: [ 171.562173] ESR = 0x0000000096000044 [ 171.566227] EC = 0x25: DABT (current EL), IL = 32 bits [ 171.573108] SET = 0, FnV = 0 [ 171.576448] EA = 0, S1PTW = 0 [ 171.579745] FSC = 0x04: level 0 translation fault [ 171.584760] Data abort info: [ 171.588012] ISV = 0, ISS = 0x00000044, ISS2 = 0x00000000 [ 171.593734] CM = 0, WnR = 1, TnD = 0, TagAccess = 0 [ 171.598962] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 171.604471] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000083837000 [ 171.611358] [0000000000000000] pgd=0000000000000000, p4d=0000000000000000 [ 171.618500] Internal error: Oops: 0000000096000044 [#1] SMP [ 171.624222] Modules linked in: powervr drm_shmem_helper drm_gpuvm... [ 171.656580] CPU: 0 UID: 0 PID: 549 Comm: bash Not tainted 7.0.0-rc2-g730b257ba723-dirty #13 PREEMPT [ 171.665773] Hardware name: BeagleBoard.org BeaglePlay (DT) [ 171.671296] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 171.678306] pc : pvr_fw_trace_mask_set+0x78/0x154 [powervr] [ 171.683959] lr : pvr_fw_trace_mask_set+0x4c/0x154 [powervr] [ 171.689593] sp : ffff8000835ebb90 [ 171.692929] x29: ffff8000835ebc00 x28: ffff000005c60f80 x27: 0000000000000000 [ 171.700130] x26: 0000000000000000 x25: ffff00000504af28 x24: 0000000000000000 [ 171.707324] x23: ffff00000504af50 x22: 0000000000000203 x21: 0000000000000000 [ 171.714518] x20: ffff000005c44a80 x19: ffff000005c457b8 x18: 0000000000000000 [ 171.721715] x17: 0000000000000000 x16: 0000000000000000 x15: 0000aaaae8887580 [ 171.728908] x14: 0000000000000000 x13: 0000000000000000 x12: ffff8000835ebc30 [ 171.736095] x11: ffff00000504af2a x10: ffff00008504af29 x9 : 0fffffffffffffff [ 171.743286] x8 : ffff8000835ebbf8 x7 : 0000000000000000 x6 : 000000000000002a [ 171.750479] x5 : ffff00000504af2e x4 : 0000000000000000 x3 : 0000000000000010 [ 171.757674] x2 : 0000000000000203 x1 : 0000000000000000 x0 : ffff8000835ebba0 [ 171.764871] Call trace: [ 171.767342] pvr_fw_trace_mask_set+0x78/0x154 [powervr] (P) [ 171.772984] simple_attr_write_xsigned.isra.0+0xe0/0x19c [ 171.778341] simple_attr_write+0x18/0x24 [ 171.782296] debugfs_attr_write+0x50/0x98 [ 171.786341] full_proxy_write+0x6c/0xa8 [ 171.790208] vfs_write+0xd4/0x350 [ 171.793561] ksys_write+0x70/0x108 [ 171.796995] __arm64_sys_write+0x1c/0x28 [ 171.800952] invoke_syscall+0x48/0x10c [ 171.804740] el0_svc_common.constprop.0+0x40/0xe0 [ 171.809487] do_el0_svc+0x1c/0x28 [ 171.812834] el0_svc+0x34/0x108 [ 171.816013] el0t_64_sync_handler+0xa0/0xe4 [ 171.820237] el0t_64_sync+0x198/0x19c [ 171.823939] Code: 32000262 b90ac293 1a931056 9134e293 (b9000036) [ 171.830073] ---[ end trace 0000000000000000 ]---
-
CVE-2026-46314 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Reject empty multisync extension to prevent infinite loop v3d_get_extensions() walks a userspace-provided singly-linked list of ioctl extensions without any bound on the chain length. A local user can craft a self-referential extension (ext->next == &ext) with zero in_sync_count and out_sync_count, which bypasses the existing duplicate- extension guard: if (se->in_sync_count || se->out_sync_count) return -EINVAL; The guard never fires because v3d_get_multisync_post_deps() returns immediately when count is zero, leaving both fields at zero on every iteration. The result is an infinite loop in kernel context, blocking the calling thread and pegging a CPU core indefinitely. Fix this by rejecting a multisync extension where both in_sync_count and out_sync_count are zero in v3d_get_multisync_submit_deps(). An empty multisync carries no synchronization information and serves no useful purpose, so returning -EINVAL for such an extension is the correct defense against this attack vector.
-
CVE-2026-46313 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: media: intel/ipu6: fix error pointer dereference In a error path isp->psys is confirmed to be an error pointer not NULL so this condition is true and the error pointer is dereferenced. So isp-psys should be set to NULL before going to out_ipu6_bus_del_devices. Detected by Smatch: drivers/media/pci/intel/ipu6/ipu6.c:690 ipu6_pci_probe() error: 'isp->psys' dereferencing possible ERR_PTR() [Sakari Ailus: Fix commit message.]
-
CVE-2026-46312 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: media: videobuf2: Set vma_flags in vb2_dma_sg_mmap vb2_dma_contig sets VMA flags VM_DONTEXPAND and VM_DONTDUMP and I do not see a reason why vb2_dma_sg should behave differently. This avoids hitting `WARN_ON(!(vma->vm_flags & VM_DONTEXPAND));` in drm_gem_mmap_obj() during mmap() of an imported dma-buf from the out of tree Apple ISP camera capture driver which uses vb2_dma_sg_memops. gst-launch-1.0 v4l2src ! gtk4paintablesink [ 38.201528] ------------[ cut here ]------------ [ 38.202135] WARNING: CPU: 7 PID: 2362 at drivers/gpu/drm/drm_gem.c:1144 drm_gem_mmap_obj+0x1f8/0x210 [ 38.203278] Modules linked in: rfcomm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device uinput nf_conntrack_netbios_ns nf_conntrack_broadcast nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables qrtr bnep nls_ascii i2c_dev loop fuse dm_multipath nfnetlink brcmfmac_wcc hid_magicmouse hci_bcm4377 brcmfmac brcmutil bluetooth ecdh_generic cfg80211 ecc btrfs xor xor_neon rfkill hid_apple raid6_pq joydev aop_als apple_nvmem_spmi industrialio snd_soc_aop apple_z2 snd_soc_cs42l84 tps6598x snd_soc_tas2764 macsmc_reboot spi_nor macsmc_hwmon rtc_macsmc gpio_macsmc macsmc_power regmap_spmi macsmc_input dockchannel_hid panel_summit appledrm nvme_apple dwc3 snd_soc_macaudio drm_client_lib nvme_core phy_apple_atc hwmon apple_sart apple_dockchannel macsmc apple_rtkit_helper spmi_apple_controller aop apple_wdt mfd_core nvmem_apple_efuses pinctrl_apple_gpio apple_isp apple_dcp videobuf2_dma_sg mux_core spi_apple [ 38.203300] videobuf2_memops i2c_pasemi_platform snd_soc_apple_mca videobuf2_v4l2 videodev clk_apple_nco videobuf2_common snd_pcm_dmaengine adpdrm asahi apple_admac adpdrm_mipi drm_dma_helper pwm_apple i2c_pasemi_core drm_display_helper mc cec apple_dart ofpart apple_soc_cpufreq leds_pwm phram [ 38.217677] CPU: 7 UID: 1000 PID: 2362 Comm: gst-launch-1.0 Tainted: G W 6.17.6+ #asahi-dev PREEMPT(full) [ 38.219040] Tainted: [W]=WARN [ 38.219398] Hardware name: Apple MacBook Pro (13-inch, M2, 2022) (DT) [ 38.220213] pstate: 21400005 (nzCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 38.221088] pc : drm_gem_mmap_obj+0x1f8/0x210 [ 38.221643] lr : drm_gem_mmap_obj+0x78/0x210 [ 38.222178] sp : ffffc0008dc678e0 [ 38.222579] x29: ffffc0008dc678e0 x28: 0000000000042a97 x27: ffff8000b701b480 [ 38.223465] x26: 00000000000000fb x25: ffffc0008dc67d20 x24: ffffc0008dc67968 [ 38.224402] x23: ffff8000e3ca5600 x22: ffff8000265b7800 x21: ffff80003000c0c0 [ 38.225279] x20: 0000000000000000 x19: ffff8000b68c5200 x18: ffffc0008dc67968 [ 38.226151] x17: 0000000000000000 x16: 0000000000000000 x15: ffffc000810a30a8 [ 38.227042] x14: 00007fff637effff x13: 00005555de91ffff x12: 00007fff63293fff [ 38.227942] x11: 0000000000000000 x10: ffff8000184ecf08 x9 : ffffc0007a1900c8 [ 38.228824] x8 : ffffc0008dc67968 x7 : 0000000000000012 x6 : ffffc0015cf1c000 [ 38.229703] x5 : ffffc0008dc676a0 x4 : ffffc00081a27dc0 x3 : 0000000000000038 [ 38.230607] x2 : 0000000000000003 x1 : 0000000000000003 x0 : 00000000100000fb [ 38.231488] Call trace: [ 38.231806] drm_gem_mmap_obj+0x1f8/0x210 (P) [ 38.232342] drm_gem_mmap+0x140/0x260 [ 38.232813] __mmap_region+0x488/0x9a0 [ 38.233277] mmap_region+0xd0/0x148 [ 38.233703] do_mmap+0x350/0x5c0 [ 38.234148] vm_mmap_pgoff+0x14c/0x200 [ 38.234612] ksys_mmap_pgoff+0x150/0x208 [ 38.235107] __arm64_sys_mmap+0x34/0x50 [ 38.235611] invoke_syscall+0x50/0x120 [ 38.236075] el0_svc_common.constprop.0+0x48/0xf0 [ 38.236680] do_el0_svc+0x24/0x38 [ 38.237113] el0_svc+0x38/0x168 [ 38.237507] el0t_64_sync_handler+0xa0/0xe8 [ 38.238034] el0t_64_sync+0x198/0x1a0 [ 38.238491] ---[ end trace 0000000000000000 ]--- There were discussions in [1] at the end of 2023 that mmap() on imported ---truncated---
-
CVE-2026-46277 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: mm/zone_device: do not touch device folio after calling ->folio_free() The contents of a device folio can immediately change after calling ->folio_free(), as the folio may be reallocated by a driver with a different order. Instead of touching the folio again to extract the pgmap, use the local stack variable when calling percpu_ref_put_many().
-
CVE-2026-46276 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix zero-size GDS range init on RDNA4 RDNA4 (GFX 12) hardware removes the GDS, GWS, and OA on-chip memory resources. The gfx_v12_0 initialisation code correctly leaves adev->gds.gds_size, adev->gds.gws_size, and adev->gds.oa_size at zero to reflect this. amdgpu_ttm_init() unconditionally calls amdgpu_ttm_init_on_chip() for each of these resources regardless of size. When the size is zero, amdgpu_ttm_init_on_chip() forwards the call to ttm_range_man_init(), which calls drm_mm_init(mm, 0, 0). drm_mm_init() immediately fires DRM_MM_BUG_ON(start + size <= start) -- trivially true when size is zero -- crashing the kernel during modprobe of amdgpu on an RX 9070 XT. Guard against this by returning 0 early from amdgpu_ttm_init_on_chip() when size_in_page is zero. This skips TTM resource manager registration for hardware resources that are absent, without affecting any other GPU type. DRM_MM_BUG_ON() only asserts if CONFIG_DRM_DEBUG_MM is enabled in the kernel config. This is apparently rarely enabled as these chips have been in the market for over a year and this issue was only reported now. Oops-Analysis: http://oops.fenrus.org/reports/bugzilla.korg/221376/report.html (cherry picked from commit 5719ce5865279cad4fd5f01011fe037168503f2d)
-
CVE-2026-46274 7.8 Élevée
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: io-wq: check that the predecessor is hashed in io_wq_remove_pending() io_wq_remove_pending() needs to fix up wq->hash_tail[] if the cancelled work was the tail of its hash bucket. When doing this, it checks whether the preceding entry in acct->work_list has the same hash value, but never checks that the predecessor is hashed at all. io_get_work_hash() is simply atomic_read(&work->flags) >> IO_WQ_HASH_SHIFT, and the hash bits are never set for non-hashed work, so it returns 0. Thus, when a hashed bucket-0 work is cancelled while a non-hashed work is its list predecessor, the check spuriously passes and a pointer to the non-hashed io_kiocb is stored in wq->hash_tail[0]. Because non-hashed work is dequeued via the fast path in io_get_next_work(), which never touches hash_tail[], the stale pointer is never cleared. Therefore, after the non-hashed io_kiocb completes and is freed back to req_cachep, wq->hash_tail[0] is a dangling pointer. The io_wq is per-task (tctx->io_wq) and survives ring open/close, so the dangling pointer persists for the lifetime of the task; the next hashed bucket-0 enqueue dereferences it in io_wq_insert_work() and wq_list_add_after() writes through freed memory. Add the missing io_wq_is_hashed() check so a non-hashed predecessor never inherits a hash_tail[] slot.
-
CVE-2026-22164 7.5 Élevée
Imagination Technologies Graphics DDK
Software installed and run as a non-privileged user may conduct improper GPU system calls to corrupt kernel heap memory. By creating resources of certain types and presenting a set of parameters to the affected interface the exploit can be used to corrupt kernel memory.
-
CVE-2025-71315 5.5 Moyenne
Linux · Linux linux kernel
In the Linux kernel, the following vulnerability has been resolved: drm/vkms: Convert to DRM's vblank timer Replace vkms' vblank timer with the DRM implementation. The DRM code is identical in concept, but differs in implementation. Vblank timers are covered in vblank helpers and initializer macros, so remove the corresponding hrtimer in struct vkms_output. The vblank timer calls vkms' custom timeout code via handle_vblank_timeout in struct drm_crtc_helper_funcs.
-
CVE-2026-49494 7.5 Élevée
Xcitium (formerly Comodo Security Solutions) Comodo Internet Security · Xcitium Client Security (XCS)
Xcitium Client Security (XCS) before 13.8.2.10019 and Comodo Internet Security (CIS) through 12.3.4.8162 (fix expected by 2026 Q3) contain an integer underflow vulnerability in the firewall driver Inspect.sys that allows remote unauthenticated attackers to crash the system by sending a crafted IPv6 packet with a declared payload length smaller than the sum of its extension-header lengths. The unsigned 64-bit payload-length value underflows to a near-maximal integer, triggering an out-of-bounds read and oversized memcpy in the Windows kernel at DISPATCH_LEVEL, resulting in a blue screen of death even on hosts with all ports blocked.
-
CVE-2026-7763 9.8 Critique
Morse Micro HaLowLink 2
A heap-based buffer overflow vulnerability in the morse.ko HaLow Wi-Fi kernel driver in Morse Micro HaLowLink 2 software versions prior to 2.11.13 allows an unauthenticated attacker within radio range to cause a Denial of Service (kernel panic) or potentially achieve Remote Code Execution via a crafted 802.11ah beacon frame containing a malformed Traffic Indication Map (TIM) Information Element. The function morse_page_slicing_process_tim_element() in page_slicing.c derives the TIM bitmap length directly from a received IE field without validating it against the fixed-size destination buffer before passing it to memset and memcpy operations, allowing up to 252 bytes of attacker-controlled data to be written beyond the buffer boundary. Because beacons are broadcast frames processed during passive scanning, no authentication, association, or user interaction is required.
-
CVE-2026-7762 9.8 Critique
Morse Micro HaLowLink 2
A heap-based buffer overflow vulnerability in the dot11ah.ko HaLow Wi-Fi kernel driver in Morse Micro HaLowLink 2 software versions prior to 2.11.13 allows an unauthenticated attacker within radio range to cause a Denial of Service (kernel panic) or potentially achieve Remote Code Execution via a crafted 802.11ah beacon or probe response frame containing a malformed S1G Capabilities Information Element (IE element ID 0xD9). The function morse_dot11ah_find_s1g_caps_for_bssid() uses the IE length field directly as the size argument to memcpy without validating it against the 15-byte destination buffer. An attacker can supply up to 255 bytes, causing an overflow of up to 240 bytes of attacker-controlled data into adjacent kernel heap memory. The vulnerability is triggerable during normal scanning without authentication, association, or user interaction.